We are one of the leading Suppliers of Moisture Measurement Meter. Flush mount, digital, microwave Moisture Measurement Meter is accurately designed following the set industrial parameters. The Hydro-Mix VII is a rugged, microwave Moisture Measurement Meter designed to be installed flush with the floor of a mixer, chute or conveyor in process control environments. Reading at 25 times per second and combined with on-board functionality such as signal processing, smoothing and averaging, the Hydro-Mix VII Moisture Measurement Meter accurately measures the moisture content of material as it passes over the ceramic faceplate. Remote configuration, calibration, diagnostics and firmware upgrades are simple using Hydronix Hydro-Com software. The linear output allows direct integration with any control system using industry standard interfaces.
Features

• Digital technology provides precise linear moisture measurement.
• Advanced Digital Signal Processing provides a clear signal with rapid response.
• Choice of measurement modes for optimizing sensor performance in a variety of applications and material types
• Fully temperature compensated measurement.
• Two analogue outputs, digital RS485 communications and configurable digital input/outputs.
• Fast response to changing conditions with 25measurements per second
• Remote communication with Hydro-Com software allows configuration of all sensor parameters including selection of sensor outputs, graphic traces of outputs, calibration of sensor readings and firmware upgrades.
• Consistent performance with no need for recalibration except for use with different materials
• Tough and reliable with proven track record
• Easily replaced ceramic faceplate and protection ring

Moisture Measurement In Bulk Materials ( Hydroprobe-II ) : The ultimate intelligent microwave sensor for measurement of moisture in sand and free flowing solid materials in bins
Range of moisture : For bulk materials the sensor will measure up to the point of saturation typically 0-20% for construction materials
Penetration : Approximately 75-100mm dependent on material
Power supply : +15Vdc to +30Vdc. 3 watts max
Refresh rate : Outputs are updated approximately 25 times per second
Analogue output : Configurable 0-20mA or 4-20mA current loop source
For 0-10Vdc output an external 500R load resistor should be connected across the analogue output at the control system
Discrete inputs : The batch average start and stop or moisture/temperature multiplexing functions can be controlled via the digital inputs, Refer to 'Connecting the Cable' section of the manual for more information.
Digital Communications : Up to isolated RS485 2-wire port

We are one of the leading Suppliers of Moisture Measurement Meter. Flush mount, digital, microwave Moisture Measurement Meter is accurately designed following the set industrial parameters. The Hydro-Mix VII is a rugged, microwave Moisture Measurement Meter designed to be installed flush with the floor of a mixer, chute or conveyor in process control environments. Reading at 25 times per second and combined with on-board functionality such as signal processing, smoothing and averaging, the Hydro-Mix VII Moisture Measurement Meter accurately measures the moisture content of material as it passes over the ceramic faceplate. Remote configuration, calibration, diagnostics and firmware upgrades are simple using Hydronix Hydro-Com software. The linear output allows direct integration with any control system using industry standard interfaces.
Features

• Digital technology provides precise linear moisture measurement.
• Advanced Digital Signal Processing provides a clear signal with rapid response.
• Choice of measurement modes for optimizing sensor performance in a variety of applications and material types
• Fully temperature compensated measurement.
• Two analogue outputs, digital RS485 communications and configurable digital input/outputs.
• Fast response to changing conditions with 25measurements per second
• Remote communication with Hydro-Com software allows configuration of all sensor parameters including selection of sensor outputs, graphic traces of outputs, calibration of sensor readings and firmware upgrades.
• Consistent performance with no need for recalibration except for use with different materials
• Tough and reliable with proven track record
• Easily replaced ceramic faceplate and protection ring

Moisture Measurement In Bulk Materials ( Hydroprobe-II ) : The ultimate intelligent microwave sensor for measurement of moisture in sand and free flowing solid materials in bins
Range of moisture : For bulk materials the sensor will measure up to the point of saturation typically 0-20% for construction materials
Penetration : Approximately 75-100mm dependent on material
Power supply : +15Vdc to +30Vdc. 3 watts max
Refresh rate : Outputs are updated approximately 25 times per second
Analogue output : Configurable 0-20mA or 4-20mA current loop source
For 0-10Vdc output an external 500R load resistor should be connected across the analogue output at the control system
Discrete inputs : The batch average start and stop or moisture/temperature multiplexing functions can be controlled via the digital inputs, Refer to 'Connecting the Cable' section of the manual for more information.
Digital Communications : Up to isolated RS485 2-wire port