FERRETERRO make Crocodile series Horizontal Plate Lifting Clamps are intended to be used in pairs, set of pairs or in tripod arrangement of lifting and transporting the steel plates in horizontal position. Our clamps are equipped with serrated gripping jaws made of special alloy steel material. These clamps can be used with all types of material in plate shape providing that plate can withstand the forces imposed on it. These clamps are suitable for single plate or bundle of plate providing the plates are of same width and size. 

FERRETERRO HORIZONTAL PLATE LIFT CLAMPS AVAILABLE IN FOLLOWING TYPES: -

• Horizontal Plate Lifting Clamp without Spring
• Horizontal Plate Lifting Clamp with Spring Loaded
• Horizontal Plate Lifting Clamp Rod Welded 
• Horizontal Roller Plate Lifting Clamp  
• Horizontal Plate Lifting Clamp Double Arm with Teeth Plate  
• Horizontal Plate Lifting Clamp with Lock 
• Horizontal Plate Lifting Clamp for Extra Hard Sheet 
• Horizontal Plate Lifting Clamp with Adjustable Jaw Opening
• PT Horizontal Plate Lifting Clamp
• Horizontal Plate Lifting Clamp Non Marring

General Features

• Induction hardened alloy steel cam
• Used in Pairs, Available 2 Ton- 20 Ton per pair
• High tensile steel welded body, higher strength
• Spring close action up to 2.5 Ton
• Powder coated finish
• Clear marking of serial no, Capacity etc
• Each Clamp individually serialized.       
• Manufacturer’s Test certificate
• Proof load 2 times of WLL 

Rigging Practices

• Do not exceed rated load capacity (WLL).
• Inspect clamp before each use.
• Ensure that plate surface is free of scale, grease, 
• oil, paint, moisture, dirt and coating that might 
• impede the contact of jaw to the plate.
• Only loads within specified jaw capacity must be lifted.
• Insert load to full depth of throat opening
• Lift slowly and smoothly, do not jerk the load.
• Do not lift the load which has sagging.
• Position clamp to balance load.
• While transporting loads ensure that load does not swing.
• If more than two clamps are used, a spreader beam must be used. Do not use 4 leg or endless slings.
• Do not drop the clamps on ground.
• Reposition the clamp if plate tilts more than 5° to the side.
• Remove the clamps from service which are subjected  to Excess Stress, Improper use or Injudicious use. 

FERRETERRO make Crocodile series Horizontal Plate Lifting Clamps are intended to be used in pairs, set of pairs or in tripod arrangement of lifting and transporting the steel plates in horizontal position. Our clamps are equipped with serrated gripping jaws made of special alloy steel material. These clamps can be used with all types of material in plate shape providing that plate can withstand the forces imposed on it. These clamps are suitable for single plate or bundle of plate providing the plates are of same width and size. 

FERRETERRO HORIZONTAL PLATE LIFT CLAMPS AVAILABLE IN FOLLOWING TYPES: -

• Horizontal Plate Lifting Clamp without Spring
• Horizontal Plate Lifting Clamp with Spring Loaded
• Horizontal Plate Lifting Clamp Rod Welded 
• Horizontal Roller Plate Lifting Clamp  
• Horizontal Plate Lifting Clamp Double Arm with Teeth Plate  
• Horizontal Plate Lifting Clamp with Lock 
• Horizontal Plate Lifting Clamp for Extra Hard Sheet 
• Horizontal Plate Lifting Clamp with Adjustable Jaw Opening
• PT Horizontal Plate Lifting Clamp
• Horizontal Plate Lifting Clamp Non Marring

General Features

• Induction hardened alloy steel cam
• Used in Pairs, Available 2 Ton- 20 Ton per pair
• High tensile steel welded body, higher strength
• Spring close action up to 2.5 Ton
• Powder coated finish
• Clear marking of serial no, Capacity etc
• Each Clamp individually serialized.       
• Manufacturer’s Test certificate
• Proof load 2 times of WLL 

Rigging Practices

• Do not exceed rated load capacity (WLL).
• Inspect clamp before each use.
• Ensure that plate surface is free of scale, grease, 
• oil, paint, moisture, dirt and coating that might 
• impede the contact of jaw to the plate.
• Only loads within specified jaw capacity must be lifted.
• Insert load to full depth of throat opening
• Lift slowly and smoothly, do not jerk the load.
• Do not lift the load which has sagging.
• Position clamp to balance load.
• While transporting loads ensure that load does not swing.
• If more than two clamps are used, a spreader beam must be used. Do not use 4 leg or endless slings.
• Do not drop the clamps on ground.
• Reposition the clamp if plate tilts more than 5° to the side.
• Remove the clamps from service which are subjected  to Excess Stress, Improper use or Injudicious use.