We are offering digital ic lab trainer (dit)
which perform (and, or, not, nand, nor, xor, x-nor, counter, flip-flop, register, multiplexer, demultiplexer practical’s) - features: the board consists of the following built-in parts:
01. + 5v d.c. At 1amp, ic regulated power supply internally connected.
02. Five, j-k master slave flip-flops with preset and clear arrangement.
03. Six, 2-input nand gates. 04. Four, 4-input nand gates.
05. Three, 4-input and-or gates. 06. Two inverters (not gates).
07. A 4-bit binary counter to demonstrate the basic principles of frequency measurement.
08. A square wave oscillator of frequency 10 hz, 1 khz and 10 khz with coarse and fine variations, demonstrate the basic principle of frequency division.
09. Completely programmable panel to make any type of counter or shift register.
10. Two pulser switches for clear and clock arrangement.
11. One mono pulser to give a 1 sec pulse.
12. Three band switches for various interconnections required in the circuit to provide greater convenience and avoiding wrong connections.
13. Two, 7-segment displays to monitor the output in decimal code.
14. Leds for visual indication of output status of each flip-flop.
15. Adequate no. Of other electronic components.
16. Mains onoff switch, fuse and jewel light.
* the unit is operative on 230v ±10% at 50hz a.c. Mains.* adequate no. Of patch cords stackable from rear both ends 4mm spring loaded plug length ½ meter.
Specification:
• logic gates :
 1. or gate 4nos.
 2. and gate 4 nos.
 3. not gate 6 nos.
 4. nand gate 4 nos.
 5. nor gate 4 nos.
 6 ex-0r gate 4 nos.
• adder ic7483 4 bit binary adder
• flip flop 1. jk flip-flop 2 nos.
 2. d latches 2 nos.
• 20 pin zip socket to test the sipdip ic’s such as multiplexer , de-multiplexer, encoder, decoder , shift register, parity checker, counters etc.
• the following ics are provided on the trainer set ic de-multiplexerdecoder 74138 (1), multiplexer 74153

We are offering digital ic lab trainer (dit)
which perform (and, or, not, nand, nor, xor, x-nor, counter, flip-flop, register, multiplexer, demultiplexer practical’s) - features: the board consists of the following built-in parts:
01. + 5v d.c. At 1amp, ic regulated power supply internally connected.
02. Five, j-k master slave flip-flops with preset and clear arrangement.
03. Six, 2-input nand gates. 04. Four, 4-input nand gates.
05. Three, 4-input and-or gates. 06. Two inverters (not gates).
07. A 4-bit binary counter to demonstrate the basic principles of frequency measurement.
08. A square wave oscillator of frequency 10 hz, 1 khz and 10 khz with coarse and fine variations, demonstrate the basic principle of frequency division.
09. Completely programmable panel to make any type of counter or shift register.
10. Two pulser switches for clear and clock arrangement.
11. One mono pulser to give a 1 sec pulse.
12. Three band switches for various interconnections required in the circuit to provide greater convenience and avoiding wrong connections.
13. Two, 7-segment displays to monitor the output in decimal code.
14. Leds for visual indication of output status of each flip-flop.
15. Adequate no. Of other electronic components.
16. Mains onoff switch, fuse and jewel light.
* the unit is operative on 230v ±10% at 50hz a.c. Mains.* adequate no. Of patch cords stackable from rear both ends 4mm spring loaded plug length ½ meter.
Specification:
• logic gates :
 1. or gate 4nos.
 2. and gate 4 nos.
 3. not gate 6 nos.
 4. nand gate 4 nos.
 5. nor gate 4 nos.
 6 ex-0r gate 4 nos.
• adder ic7483 4 bit binary adder
• flip flop 1. jk flip-flop 2 nos.
 2. d latches 2 nos.
• 20 pin zip socket to test the sipdip ic’s such as multiplexer , de-multiplexer, encoder, decoder , shift register, parity checker, counters etc.
• the following ics are provided on the trainer set ic de-multiplexerdecoder 74138 (1), multiplexer 74153