We are one of the leading suppliers of Industrial Power Plug and Socket Panels in chennai. we fabricate the Plug and Socket panels as per your design / BOQ and the best in the Industrial safety standards.

The Detuned Harmonic Filter is comprised of a capacitor connected in series of a suitable reactor. The rectifier impedance & capacitor impedances are selected in a fashion that capacitor doesn't tune to the frequencies of harmonics generated by loads & hence its life is increased.
In the case of normal APFC panel, chances are there that capacitors tune to the load harmonics frequencies & hence life of the capacitors reduce. We do provides thorough our power quality Harmonic Testing of the existing system requirement of Power Factor Correction & calculates the required amount of reactor & capacitor to fulfill the system's requirement of a Detuned APFC Panel.

Merits :

• Apart from maintaining the system power factor to a predefined target like 99%, Detuned APFC Panel prevents capacitors from getting overloaded due to harmonics of the order of 5th & above.
• Switching current amplification will not happen.
• Overloading of the system transformer & other rotating equipment will be prevented.

 Since 2004 We are the leading manufacturer of Automatic Power Factor Correction ( APFC ) Panels in Chennai, Tamilnadu, India. An automatic power factor correction unit is used to improve power factor. A power factor correction unit usually consists of a number of capacitors that are switched by means of contactors. These contactors are controlled by a regulator that measures power factor in an electrical network. To be able to measure power factor, the regulator uses a current transformer to measure the current in one phase.

• Depending on the load and power factor of the network, the power factor controller will switch the necessary blocks of capacitors in steps to make sure the power factor stays above a selected value (usually demanded by the energy supplier), Automatic Power Factor Capacitor in chennai, Tamilnadu, India. Power Factor Panel Mfrs in Chennai
• In view of constantly rising power tariff and the penalties charged by the State Electricity Board, it is incumbent for any HT / LT Consumer to install an apt APFC system for cut down the cost of Power Factor penalty and also to save Energy by consistently maintaining the higher Power Factor.
• The Low Power Factor leads to the poor efficiency, thereby increasing the apparent power drawn   (KVA) from the distribution network. This would reflects in overloading of Transformer, Bus bar Chamber, Switchgears, Cables & other distribution components within the consumers area.
• Low Power Factor leads to poor power efficiency there by increasing the apparent power drawn from the distribution network this results in overloading of Transformer, Cables & other distribution devices within the Industry or consumer area.  An apt power factor control system ensures optimum power for the running loads.

BENEFITS

• Avoids penalties for the Low Power Factor
• Reduction in the Maximum Demand (KVA)
• Reduction in the energy
• Claim higher Power Factor Incentives
• Longer life of the existing electrical distribution components
• Lower Electricity charge.

Ranges :

• LTCT 30 KVAr to 150 KVAr APFC Panel Manufactures in Chennai
• HT : 150 KVAr to 800 KVAr APFC Panel Manufactures in Chennai

Major Components :

• Capacitors :EPCOS from SIEMENS / L & T / Schneider / MOMAYA
• Power Factor Controllers : BELUK / EPCOS / MIKRO
• Switch Gears : L & T / SIEMENS / ABB / Schneider / CHINT

we are the leading manufacturer of automatic power factor correction ( apfc ) panels in chennai, tamilnadu, india.

in view of constantly rising power tariff and the penalties charged by the state electricity board, it is incumbent for any ht / lt consumer to install an apt apfc system for cut down the cost of power factor penalty and also to save energy by consistently maintaining the higher power factor.

ltct 30 kvar to 150 kvar apfc panel manufactures in chennai

ht : 150 kvar to 800 kvar apfc panel manufactures in chennai

Having a respected name in the industry, we are manufacturing, distributing, trading and supplying a Maximum Demand Controller Panel in Chennai, Tamil Nadu, India. The offered maximum demand controllers will be provided in different specifications as per our clients demands. Our vendors use best material only for manufacturing these maximum demand controllers along with the leading techniques. Apart from this, our whole range of load mangers are acclHaving a respected name in the industry, we are manufacturing, distributing, trading and supplying a Maximum Demand Controller Panel in Chennai, Tamil Nadu, India. The offered maximum demand controllers will be provided in different specifications as per our clients demands. Our vendors use best material only for manufacturing these maximum demand controllers along with the leading techniques. Apart from this, our whole range of load mangers are acclaimed for their high performance, rust proof & long service life. These maximum demand controllers are meticulously examined on previously stated parameters of quality to supply defect free range. Features: High performance Low maintenance Operational fluency Technical Specifications: Model: PCM 9506 System: Suitable for LT/HT Application Input Voltage: 415V or 110V LL Nominal Range 80 - 600 V LL Input Current: Input Current field programmable Range1A or 5A Working Range: 0.4% to 120% (4 mA to 1.2A for 1A) (20 mA to 6A for 5A) Overload: 2 times continuously & 10 times for 3 Secs. Burden on Voltage Input: 0.25VA Burden on Current Input: 0.25VA Frequency: 45-55 HZ Item code: 76985293aimed for their high performance, rust proof & long service life. These maximum demand controllers are meticulously examined on previously stated parameters of quality to supply defect free range. Features: High performance Low maintenance Operational fluency Technical Specifications: Model: PCM 9506 System: Suitable for LT/HT Application Input Voltage: 415V or 110V LL Nominal Range 80 - 600 V LL Input Current: Input Current field programmable Range1A or 5A Working Range: 0.4% to 120% (4 mA to 1.2A for 1A) (20 mA to 6A for 5A) Overload: 2 times continuously & 10 times for 3 Secs. Burden on Voltage Input: 0.25VA Burden on Current Input: 0.25VA Frequency: 45-55 HZ Item code: 76985293.

The Detuned Harmonic Filteisl comprises of a capacitor connected in series of a suitable reactor. The rectifer impedance & capacitor impedances are selected in a fashion that capacitor doesn't tune to the frequencies of harmonics generated by loads & hence its life is increased. In case of normal APFC panel, chances are there that capacitors tune to the load harmonics frequencies & hence life of the capacitors reduce. We do provides thorough our power quality Harmonic Tessting of the existing system requirement of Power Factor Correction & calculates the required amount of reactor & capacitor to fulfill the system's requirement of a Detuned APFC Panel. Merits: 1. Apart from maintaining the system power factor to a predefined target like 99%, Detuned APFC Panel prevents capacitors from getting overloaded due to harmonics of the order of 5th & above. 2. Switching current amplification will not happen. 3. Overloading of the system transformer & other roatingequipements will be prevented.

We are the leading manufactures of Automatic Power Factor Capacitor Panels in Chennai. We do provide sales and service support for the all models

Detuned Reactor APFC Panel Suppliers Mfrs, Chennai Tamil Nadu

• Detuned Filter Reactor
• EPCOS 7 % Detuned Copper Reactor
• APFC Panels Detuned Reactor
• 7% Detuned Reactor - APFC Panels

The company has cemented its presence amid the top-notch Manufacturers, Distributors and Suppliers of 7% Detuned Reactor Panel in Chennai, Tamil Nadu, India. The entire array is designed and produced in accordance with industry standards. As a result, our 7% Detuned Reactor Panels come with high strength and performance abilities.

We are highly celebrated manufacturer, supplier and exporter of all dependable range of Detuned Harmonic Filter in Chennai, Tamil Nadu, India. The Detuned Harmonic Filter is comprised of a capacitor connected in series of a suitable reactor. The rectifier impedance & capacitor impedances are selected in a fashion that capacitor doesn't tune to the frequencies of harmonics generated by loads & hence its life is increased. In the case of normal APFC panel, chances are there those capacitors tune to the load harmonics frequencies & hence life of the capacitors reduce. We do provide thorough our power quality Harmonic Testing of the existing system requirement of Power Factor Correction & calculates the required amount of reactor & capacitor to fulfill the system's requirement of a Detuned APFC Panel. Merits: Apart from maintaining the system power factor to a predefined target like 99%, Detuned APFC Panel prevents capacitors from getting overloaded due to harmonics of the order of 5th & above. Switching current amplification will not happen. Overloading of the system transformer & other rotating equipment will be prevented.

We are one of the leading suppliers of Industrial Power Plug and Socket Panels in chennai. we fabricate the Plug and Socket panels as per your design / BOQ and the best in the Industrial safety standards.

The Detuned Harmonic Filter is comprised of a capacitor connected in series of a suitable reactor. The rectifier impedance & capacitor impedances are selected in a fashion that capacitor doesn't tune to the frequencies of harmonics generated by loads & hence its life is increased.
In the case of normal APFC panel, chances are there that capacitors tune to the load harmonics frequencies & hence life of the capacitors reduce. We do provides thorough our power quality Harmonic Testing of the existing system requirement of Power Factor Correction & calculates the required amount of reactor & capacitor to fulfill the system's requirement of a Detuned APFC Panel.

Merits :

• Apart from maintaining the system power factor to a predefined target like 99%, Detuned APFC Panel prevents capacitors from getting overloaded due to harmonics of the order of 5th & above.
• Switching current amplification will not happen.
• Overloading of the system transformer & other rotating equipment will be prevented.

 Since 2004 We are the leading manufacturer of Automatic Power Factor Correction ( APFC ) Panels in Chennai, Tamilnadu, India. An automatic power factor correction unit is used to improve power factor. A power factor correction unit usually consists of a number of capacitors that are switched by means of contactors. These contactors are controlled by a regulator that measures power factor in an electrical network. To be able to measure power factor, the regulator uses a current transformer to measure the current in one phase.

• Depending on the load and power factor of the network, the power factor controller will switch the necessary blocks of capacitors in steps to make sure the power factor stays above a selected value (usually demanded by the energy supplier), Automatic Power Factor Capacitor in chennai, Tamilnadu, India. Power Factor Panel Mfrs in Chennai
• In view of constantly rising power tariff and the penalties charged by the State Electricity Board, it is incumbent for any HT / LT Consumer to install an apt APFC system for cut down the cost of Power Factor penalty and also to save Energy by consistently maintaining the higher Power Factor.
• The Low Power Factor leads to the poor efficiency, thereby increasing the apparent power drawn   (KVA) from the distribution network. This would reflects in overloading of Transformer, Bus bar Chamber, Switchgears, Cables & other distribution components within the consumers area.
• Low Power Factor leads to poor power efficiency there by increasing the apparent power drawn from the distribution network this results in overloading of Transformer, Cables & other distribution devices within the Industry or consumer area.  An apt power factor control system ensures optimum power for the running loads.

BENEFITS

• Avoids penalties for the Low Power Factor
• Reduction in the Maximum Demand (KVA)
• Reduction in the energy
• Claim higher Power Factor Incentives
• Longer life of the existing electrical distribution components
• Lower Electricity charge.

Ranges :

• LTCT 30 KVAr to 150 KVAr APFC Panel Manufactures in Chennai
• HT : 150 KVAr to 800 KVAr APFC Panel Manufactures in Chennai

Major Components :

• Capacitors :EPCOS from SIEMENS / L & T / Schneider / MOMAYA
• Power Factor Controllers : BELUK / EPCOS / MIKRO
• Switch Gears : L & T / SIEMENS / ABB / Schneider / CHINT

we are the leading manufacturer of automatic power factor correction ( apfc ) panels in chennai, tamilnadu, india.

in view of constantly rising power tariff and the penalties charged by the state electricity board, it is incumbent for any ht / lt consumer to install an apt apfc system for cut down the cost of power factor penalty and also to save energy by consistently maintaining the higher power factor.

ltct 30 kvar to 150 kvar apfc panel manufactures in chennai

ht : 150 kvar to 800 kvar apfc panel manufactures in chennai

Having a respected name in the industry, we are manufacturing, distributing, trading and supplying a Maximum Demand Controller Panel in Chennai, Tamil Nadu, India. The offered maximum demand controllers will be provided in different specifications as per our clients demands. Our vendors use best material only for manufacturing these maximum demand controllers along with the leading techniques. Apart from this, our whole range of load mangers are acclHaving a respected name in the industry, we are manufacturing, distributing, trading and supplying a Maximum Demand Controller Panel in Chennai, Tamil Nadu, India. The offered maximum demand controllers will be provided in different specifications as per our clients demands. Our vendors use best material only for manufacturing these maximum demand controllers along with the leading techniques. Apart from this, our whole range of load mangers are acclaimed for their high performance, rust proof & long service life. These maximum demand controllers are meticulously examined on previously stated parameters of quality to supply defect free range. Features: High performance Low maintenance Operational fluency Technical Specifications: Model: PCM 9506 System: Suitable for LT/HT Application Input Voltage: 415V or 110V LL Nominal Range 80 - 600 V LL Input Current: Input Current field programmable Range1A or 5A Working Range: 0.4% to 120% (4 mA to 1.2A for 1A) (20 mA to 6A for 5A) Overload: 2 times continuously & 10 times for 3 Secs. Burden on Voltage Input: 0.25VA Burden on Current Input: 0.25VA Frequency: 45-55 HZ Item code: 76985293aimed for their high performance, rust proof & long service life. These maximum demand controllers are meticulously examined on previously stated parameters of quality to supply defect free range. Features: High performance Low maintenance Operational fluency Technical Specifications: Model: PCM 9506 System: Suitable for LT/HT Application Input Voltage: 415V or 110V LL Nominal Range 80 - 600 V LL Input Current: Input Current field programmable Range1A or 5A Working Range: 0.4% to 120% (4 mA to 1.2A for 1A) (20 mA to 6A for 5A) Overload: 2 times continuously & 10 times for 3 Secs. Burden on Voltage Input: 0.25VA Burden on Current Input: 0.25VA Frequency: 45-55 HZ Item code: 76985293.

The Detuned Harmonic Filteisl comprises of a capacitor connected in series of a suitable reactor. The rectifer impedance & capacitor impedances are selected in a fashion that capacitor doesn't tune to the frequencies of harmonics generated by loads & hence its life is increased. In case of normal APFC panel, chances are there that capacitors tune to the load harmonics frequencies & hence life of the capacitors reduce. We do provides thorough our power quality Harmonic Tessting of the existing system requirement of Power Factor Correction & calculates the required amount of reactor & capacitor to fulfill the system's requirement of a Detuned APFC Panel. Merits: 1. Apart from maintaining the system power factor to a predefined target like 99%, Detuned APFC Panel prevents capacitors from getting overloaded due to harmonics of the order of 5th & above. 2. Switching current amplification will not happen. 3. Overloading of the system transformer & other roatingequipements will be prevented.

We are the leading manufactures of Automatic Power Factor Capacitor Panels in Chennai. We do provide sales and service support for the all models

Detuned Reactor APFC Panel Suppliers Mfrs, Chennai Tamil Nadu

• Detuned Filter Reactor
• EPCOS 7 % Detuned Copper Reactor
• APFC Panels Detuned Reactor
• 7% Detuned Reactor - APFC Panels

The company has cemented its presence amid the top-notch Manufacturers, Distributors and Suppliers of 7% Detuned Reactor Panel in Chennai, Tamil Nadu, India. The entire array is designed and produced in accordance with industry standards. As a result, our 7% Detuned Reactor Panels come with high strength and performance abilities.

We are highly celebrated manufacturer, supplier and exporter of all dependable range of Detuned Harmonic Filter in Chennai, Tamil Nadu, India. The Detuned Harmonic Filter is comprised of a capacitor connected in series of a suitable reactor. The rectifier impedance & capacitor impedances are selected in a fashion that capacitor doesn't tune to the frequencies of harmonics generated by loads & hence its life is increased. In the case of normal APFC panel, chances are there those capacitors tune to the load harmonics frequencies & hence life of the capacitors reduce. We do provide thorough our power quality Harmonic Testing of the existing system requirement of Power Factor Correction & calculates the required amount of reactor & capacitor to fulfill the system's requirement of a Detuned APFC Panel. Merits: Apart from maintaining the system power factor to a predefined target like 99%, Detuned APFC Panel prevents capacitors from getting overloaded due to harmonics of the order of 5th & above. Switching current amplification will not happen. Overloading of the system transformer & other rotating equipment will be prevented.