Laboratory Equipments #5879151

Double walled construction inner chamber made of stainless steel / M.S and exterior made of G.I powder coated. Gap between the two walls is filled with glass wool insulation, provided with S.S shelves. Temperature is controlled by Digital PID controller. Temp range 5C to 60C, accuracy 0.5C.

Incubators are sturdy double walled units

Inner Chamber made of S.S. and outer made of Mild Steel with Powder coating.

Gap between the walls fitted with glass wool insulation to avoid heat loses.

Heating elements are made of high grade chrome plated nichrome wire. Temperature is controlled by thermostat.

Temperature range 5C above ambient to 600C and Accuracy: 2C

Air Ventilations is provided on the top of the unit to remove the hot gases I fumes.

In Lab type oven heaters are placed in the bottom oldest the unit.

All the control switches & pilot lamps are fitted on the front panel.

Trays should be supplied with G.I. wire mesh.

Hot Air Oven is laboratory tools used for various application. Basic principle of the hot air oven is that the fresh air from the outside is blown trough the hot wire or heated metal or ceramic material . The air gets heated and enter into the insulated chamber . The design of the hot air released area is in such a way that the hot air can reach to the every corner of the air oven . During this process, the oxygen from air touches the hot filament and it oxidizes the red hot wire . The wire resistance changes . At the end the heater gets break .

Our design of hot air oven is designed to handle even this type of the environment.

Ovens are double walled.

Inner chamber made of either M.S. or S.S.304.

Gap between the two walled filled with ceramic insulation to avoid heat of loses with insulation of 150 mm.

Heating element are made of special type air heater of S.S.U Type tubular heater.

With special type of wiring connection from out side body

Supplied with air draft motorized blower to circulate uniform temp. Thought out chamber temp. range 50C to 250C with accuracy of 2C controlled by digital temp.Controller cum indicator

COD Digester is the most accepted Thermo reactor for Determination of Chemical Oxygen Demand in Various Substances. Chemical Oxygen Demand (COD) is a Measure of the Capacity of Water to Consume Oxygen during the Decomposition of Organic Matter and the Oxidation of Inorganic Chemicals such as Ammonia and Nitrite. COD Measurements are commonly made on Samples of Waste Waters or of Natural Waters Contaminated by Domestic or Industrial Wastes. Chemical Oxygen Demand is measured as a Standardized Laboratory assay in which a closed Water Sample is incubated with a Strong Chemical Oxidant under Specific Conditions of Temperature and for a Particular Period of Time. Our cod Digester is specially designed as per IS & ASTM standard suitable for 6- tubes or 9 tubes. COD digester is used for chemical oxygen demand method for monitoring waste water influent and industrial process water. Digester block made out of high quality Alluminium . The Cod Digester is provided with highly insulated between block & exterior which is made out of G.I powder coated or M.S powder coated finish. The COD Digester is equipped with microprocessor based PID controller with dual display seven segments four digit digital controller cum indicator with timer of 120 minute with alarm. The digester block is suitable for 38 mm diameter tubes and 600 mm height air condenser.

Chemical Oxygen Demand Digester Designed for digestion of COD test samples and multi-function dry bath heating.C
Precise temperature control from ambient +5 C to 150 C with 1 C accuracy.
Users self compensation functions for temperature to counter for difference between block temperature and sample temperature.
Fitted with Microprocessor Based Digital Temperature
Indicator cum Controller for auto control with respect to time and temperature and is also fitted with in-built buzzer timer for auto time control to indicate cycle end.
Microprocessor Based Digital Temperature Indicator cum Controller having dual four digit seven segment digital display for set value and process value.
Recessed well/cavity accommodates aluminium or S.S insert block.
Samples after being digested for 2 hours can be analyzed using calorimeter or conventional titration method.

Temperature Range: +5C form ambient to 150 C/ 250C
Temperature Sensitivity: +/- 1 c or better.
Resolution: 0.1 C

This is made as specified by IP-15, ASTM-D-97-57 & IS 1448-1970. The pour point is the lowest temperature at which the oil will just fall to flow. The apparatus consists of a main cooling bath made of stainless steel sheet and stand unit with drain plug and cover with provision for fitting thermometer and a filling aperture for adding freezing mixture. A glass jar for containing oils, jacket, disc and gasket is standard scope of supply.

MODEL : SM-35US C
TANK SIZE :9" X 6" X 4" ( L X W X H )C
OUTER SIZE : 12" X 9.8" X 11.6" ( L X W X H )
TANK : SS 304 (16G)
ENCLOSURE :SS 304 (18 / 20 G)
TANK CAPACITY : 3.5 LITER'S
ULTRASONIC POWER : 100 WATTS.
HEATER POWER : 150 WATTS
ULTRASONIC FREQUENCY : 33KHz 3Khz.
TIMER : 0 TO 99 MINUTES.
POWER INPUT : 230VAC.
TRANSDUCERS : PZT TYPE BONDED AT THE BOTTOM OF THE TANK(MORGAN UK MAKE )
ULTRASONIC GENERATOR : ADVANCE LATEST MOSFET / IGBT BASED SMPS.
ACCESSORIES : LID, BASKET, POWERCORD
OPTIONAL FEATURES : ALSO AVAILABLE IN SUPERMICRO MODEL(WITH DIGITAL TEMPERATURE CONTROLLER)