Shiv Enterprise

M26500 Is A Butene Comonomer Based Linear Low Density Polyethylene Grade With Narrow Molecular Weight Distribution And Optimum Levels Of Antioxidants. It Offers Excellent Processability And Is Mainly Recommended For Preparing Masterbatch. This Grade Can Also Be Used For Producing Injection Moulded Lids, Containers, Houseware & General Purpose Articles As It Exhibits Good Flexibility, Low Warpage And Good Fluidity. 

Applications 

Masterbatches, Shopping Baskets, Lids, Hot Melt Adhesives, Powder Coating. 

Regulatory Information 

Meets The Requirements Stipulated In Standard Is: 10146 On "Specification For Polyethylene For Safe Use In Contact With Foodstuffs, Pharmaceuticals, And Drinking Water". It Also Conforms To The Positive List Of Constituents As Prescribed In Is: 10141. The Grade And The Additives Incorporated In It Also Comply With The Fda:cfr Title 21, 177.1520, Olefin Polymers. 

Storage Recommendations 

Bags Should Be Stored In Dry/closed Conditions At Temperatures Below 50°c And Protected From Uv/direct Sunlight. 

Storage Recommendations

Bags should be stored in dry / closed conditions at temperatures below 50°C and protected from UV / direct sunlight

Storage Recommendations

Bags should be stored in dry / closed conditions at temperatures below 50°C and protected from UV / direct sunlight

Storage Recommendations

Bags should be stored in dry / closed conditions at temperatures below 50°C and protected from UV / direct sunlight

F46003 is a High Density Polyethylene grade suitable for general purpose blown film & extrusion blow moulding applications. Articles blown fromthis grade exhibit moderate to good stiffness. The resin offers good melt strength, ESCR and impact resistance.

Applications

Used for producing blown film and is recommended for use in carry bags and co-extruded film structures, general purpose blow molded containers. F46003 is not intended for use in medical and pharmaceutical applications.

Regulatory Information

• Meets the requirements stipulated in standard IS: I0146 on "Specification for Polyethylene for safe use in contact with foodstuffs, pharmaceuticals, and drinking water". It also conforms to IS 16738:2018 “Positive List of Constituents for Polypropylene, Polyethylene and their Copolymers for its Safe Use in Contact with Foodstuffs and Pharmaceuticals”
• The grade and the additives incorporated in it also comply with the FDA: CFR Title 21, 177.1520, Olefin polymers 

Storage Recommendations

Bags should be stored in dry/closed conditions at temperatures below 50°C and protected from UV / direct sunlight. 

Relene 45GP004 (PE:80) is a natural coloured grade for pipe extrusion.  It possesses bimodal molecular weight distribution, which improves processability. This grade meets the MFI, Density & Hydrostatic strength requirements of material grade PE:80 as per IS 4984:2016 for 'Polyethytene pipes for Water Supply Specification' when incorporated with adequate quantity of carbon black as specified in clause 5.3 of IS: 4984: 2016. It will also meet the requirements of the designation PE EL C45T006 mentioned in the clause 4.2 of IS 7328: 1992. 

Pipe made from Rellene 45GP004 grade passes the Internal Pressure Creep Rupture Test when tested with 4.5 MPa induced stress at 80°C for 165 hrs and with 4.9 MPa induced stress at 80°C for 48 hrs as per clause 8.1 of IS 4984:2016, thereby meeting the requirement of PE:80 grade. 

This grade conforms to ISO 4427 specification shown below and has been certified for MRS > 8 MPa as per ISO 9080.

Regulatory Information 

• Meets the requirements stipulated in standard IS: 10146:1982 on "Specification for Polyethylene for safe use in contact with foodstuffs, pharmaceuticals, and drinking water". It also conforms to IS 16738:2018 "Positive List of Constituents for Polypropylene, Polyethylene and their Copolymers for its Safe Use in Contact with Foodstuffs and Pharmaceuticals" 
• The grade and the additives incorporated in it also comply with the FDA: CFR Title 21, 177.1520, Olefin polymers. 
• The level of antioxidant in 45GP004 is not more than 0.3% by mass of the resin

Storage Recommendations 

Bags should be stored in dry/closed conditions at temperatures below 50°C and protected from UV/direct sunlight

Polysure M0252S is 1-hexene comonomer based High Density Polyethylene, produced by Gas Phase – UNIPOLTM PE technology, suitable for Injection Molding and Continuous Compression Molding processes. M0252S resin offers superior organoleptic properties, ESCR & Low Warpage. The products made from this grade will have good dimensional stability, appearance, and stiffness.

Processing Guidelines

• Barrel Temperature : 190-220°C 
• Mold Temperature : 20-30°C 

Storage & Handling

Bags should be stored in dry & dust free environment at temperature below 50°C and Prevent from direct exposure to sunlight & heat to avoid quality deterioration. 

Regulatory Requirements

M0252S to be manufactured complying the requirements specified in IS 10146 on "Specification for Polyethylene for its safe in contact with Foodstuff, Pharmaceutical & Drinking water". Furthermore, the Additives added in this grade formulation compiles to the "Positive list of constituents for Polypropylene, Polyethylene and their Copolymers for its safe use in contact with Foodstuffs & Pharmaceuticals' as laid down under IS 16738:2018. In general, the additives & constituents used in the grade are in line with requirement laid down under FDA: CFR Title 21, 177.1520, Olefin Polymers.