S S POWER SYSTEM

Greater Noida, Uttar Pradesh

• Operating Volt: 140- 280 VAC (P-N)
• Contactor coil activates only for 1 sec
• Automatic load transfer among Mains and genset
• Auto Start/Auto Stop the Genset when Mains fails/restores
• Mains input: 3 phase, Gen input: 3 phase
• LED Indications for mains (R-Y-B), gen ON, load ON, mode & fault
• Minimum changeover time to protect sensitive equipment
• Mains restore delay time: 5 sec, Cranking time: 3-5 sec., Cool down time: 10 sec
• Gen output delay time: 8-10 sec, 3 cranking attempts for genset with 15 sec intervals
• Microcontrolled based system with Electrical interlocking
• Audio visual alarm on common Genset faults
• Soft button for Auto/Manual mode selection, manual start/stop
• Battery charger inbuilt
• Compatible with new electronic controller-based and old key-type genset as well.
• Three pole and four pole available
• Current rating 63 Amp. to 150 Amp., suitable for upto 63kVA genset
• Fabrication: Powder Coated GI Box, Wall mounting, compact size
• Works well on low/high voltages, no chattering or coil burning, smooth switching
• Long life and maintenance free
• Heavy duty DMC connection terminal block
• Screw tight connection for 63 A. and ring type thimble for 100 and 150 A.
• Provision for Remote operation (auto/manual, start/stop).

It is used in electricity supply systems to divide electrical power feed into other circuits. It has a key role in supplying power and protecting permanently installed equipment for building such as power and lighting facilities while providing a protective fuse or circuit breaker for each circuit, in a common enclosure.

Features :

• Manufactured for multiple operations with PMC Technology advantages without any problems like overheating & burning of coil.
• Manufactured in GI sheets to provide high strength, longer service life, corrosion free, low maintenance cost.
• Provided with hinges, fixings and locks & fully enclosed switchgear.

SU BTECH make CLD cum auto changeover, which is a fully automatic high precision system for efficient distribution of individually rationed generator power, is an advantageous and cost effective alternative to conventional manual cha ngeovers. The auto changeover cum current limiting device (CLD) works as a changeover and also gives protection to generator due to overload and abnormal supply. It is a Micro-controlled Pre-Programed overload protection system for multiple operations, mostly used for generators and power backup multi storied societies, malls, apartments etc.

Features:

• Settable voltage range for mains and genset
• Settable overload limit for genset
• Auto trip on overload to prevent genset overloading
• Overload trip time will decrease as overload increase
• Once tripped, auto re-starts after 10 seconds (max) and so on upto 5 trials
• Auto trip on under/over voltage on mains and genset to avoid damages to appliances
• Continue glowing LEDs on healthy conditions & blinking LEDs on source waiting and faulty conditions
• After 5 trials, tripped permanently for 3 minutes
• Automatically tries again after 3 min or user can reset manually or wait for the mains
• Safeguards generator by gradual loading and precision monitoring
• Assured availability of allotted current; no less, no more
• Significant saving on wall space and wiring.

Auto main failure panel is used for the automatic operation of the Genset. It monitors the power availability of both “MAINS” and “GENERATOR” automatically, and delivers you the healthy power continuously; on the other hand it will monitor the operation state for Generator while the Generator is running. During abnormal or common faults of generators, AMF Panel will give you both the visual (by LED) and audio signal feedback.

Features :

• Auto Start & Auto Stop the Genset when Mains fails & restores respectively.
• Cranking standard -  three cranking attempts with 15 sec intervals.
• Auto / Manual mode selector available, automatically changes lines from Mains and Gen Line and vice versa.
• Mains restoration delay time - 10 sec, start delay time: 3-5 sec. cool down time: 30-40 sec, DG output delay time: 8-10 sec.
• Low/high Voltage protection, Reverse phase protection (optional)
• Digital Volt, Amp., Hz. Meters & 5 Indication for Mains, DG and load in Display
• Contactor Coil Voltage: 180-260 VAC & Pre Magnetic Contactor Coil Voltage- 130-280VAC

Availability : 40 Amp. to 500 Amp.

Auto changeover the need for continuous power supply and its reliability has increased rapidly over the years, especially in all those areas where continuous power supply is must. Their complexity has increased as continuous information and communications are needed to control automated process, be in industries, commercial complexes, hospitals, hotels or even modern residences. Automatic Changeover from main supply to stand by supply is vital for all the above kinds of load. In case of both DG Supply as well as mains supply, comes together then priority will be of mains because the automatic changeover will change DG supply to mains. In the event of power failure, the standby power is usually expected to take over automatically. Electrical starting equipment, battery bank and diesel generator are required for the automatic operation. The automatic transfer is achieved mostly by AMF Panels. The process of on-load transfer has to be monitored & controlled for a smooth Changeover and within safety limits of all elements of the system.

Features:

• Operating Voltage 130V to 280V
• Inbuilt SMPS supply to operate the circuit
• Simplifies electrical complexity with NFC System
• LED Indication for MAINS ON & GENERATOR ON
• Potential free contact for Start/stop of generators (optional)
• Genset Stop system is inbuilt, especially for Portable Generators
• Time Delay on generator mode in changeover in higher capadty
• When main supply is resumed, the connected load is automatically shifted to mains
• Powder Coated 130 Compact size Wall mounting, Temper proof and maintenance free
• Microcontroller based technology with Pre-Program interlocking to prevent short circuit.
• Single Phasing does not affect the overall output: Only the absent phase of mains will fail in output, not all three phases will fail
• Switch over time for genset to main is very minimum so that even sensitive equipment's do not get "OFF" during the switch over
• Its unique circuit design enables the relay to be in 'ON' position only while the genset is in use. During main supply the relay remains in 'OFF' position. Due to this the life of changeover gets increase.
• No Time Delay for output on resumption of Mains Supply whenever DG's not working. In that time Interval as load remain connected to the mains only. (Even in the absence of one or two phase also)
• DG Supply can/cannot be used at the time of single phasing of Mains supply. (Because some users are satisfied even in single phase to save the diesel cost.)
• In the Presence of supply in all three phase, load automatically shifts from DG to Mains with a time delay of 5 Sec. But when there is one or two phase supply, Load will not shift from DG to Mains only.

It is used to overcome problems likes single phasing, reverse phasing and unbalance supply to protect the electrical/electronic appliances.

Features :

\n
• Auto cut off on single phasing & unbalances supply.
\n
• Auto corrects in Reverse phasing
\n
• Switching time is 10 second with an Operating Voltage 130V to 280V.
\n
• Temper proof and maintenance free, powder coated box.
\n
• Microcontroller based technology with Pre Program interlocking to prevent short circuit.
\n
• Minimum heat dissipation & energy losses.
\n
• Remove problem of sparking & burning with the usage of Pre Magnetic Contactor.
\n

Digital Time Switches are used where electrical equipment must be periodically switched on and off for pre-programmed daily or weekly times. Digital time switches available with only 5 pin timer. The 5 pin model connection is an AC 220 is just like a switch. It can be used for switching to any application individually or with group of appliances.

Features :

• Digital programmable Daily, weekly timer basis.
• Upto 16 programs daily
• Inbuilt rechargeable V80H battery for memory backup means no issue of replacing battery, Battery charge last for at least 1-2 months without charge. i.e. Without AC supply connectivity.
• Led power indicator, LCD on screen displays for on and off switching status.
• Contact – single pole - single throw, Contact capacity-16 Amp, 240 VAC.
• Running accuracy ± 1 second / day at 20°, Minimum time setting - 1 minute.
• It can be used for street lights, motors, T.V., AC etc.

BASE

• Manual motor starter with MCB

• Analog ampere meter & Analog Volt meter

• Manual start/ Manual stop by switch

• Power on LED indication

• Used for oil filled submersible pump

Available in : 1 HP & 1.5 HP

E-BASE

• Manual motor starter with MCB

• Analog ampere meter & Analog Volt meter

• Manual start/ Manual stop by smooth push buttons

• Power on & Motor on LED indication

• Voltage check button

• Used for oil filled & water filled submersible pump

Available in : 1 HP, 1.5 HP, 2 HP & 3 HP

Royal

• Digital Overload Relay

• Over / Under load cut-off

• Over / Under voltage cut-off

• Digital Ampere & Volt meter

• MCB for Protection

• Startup delay time

• Push Buttons for Start & Stop

• Elegant & Sleek Design

Available in : 1 HP, 1.5 HP, 2 HP, 3 HP, 3 HP (PMC), 5 HP (PMC), 7.5 HP (PMC)

Super Royal

• Digital Overload Relay

• Digital Water level indication

• Over / Under load cut-off

• Over / Under voltage cut-off

• Digital Ampere & Volt meter

• MCB for Protection

• Startup delay time

• Soft push buttons for Start & Stop

• Elegant & Sleek Design

• Magnetic float sensor (included) (2 sensors and 4 sensor system available)

Available in : 1 HP, 1.5 HP, 2 HP & 3 HP

It is used to maintain power factor by the use of capacitor bank to suit the variations in inductive/resistive loads. Specially in industrial sector, heavy inductive loads are very common to give low power factor, which results in higher demand charges and also low power factor penalties. APFC panel provides automatic switching operation of the suitable capacitor bank for fixing power factor from load fluctuation.

Features :

• User friendly microprocessor based APFC relay.
• Modular design with easier assembly, Installation & maintenance.
• Power factor correction done with help of power factor controller & power contactors by switching In/Out 6/8/12 steps of capacitor banks.
• Used for three phase loads.

Availability : Contactor based and PMC based

We are manufacturer ofSemi/Fully Automatic Pump Controller or water level controller for your home and industry. It continuously monitors the liquid level of the overhead tank and reservoir.The Automatic pump controller controls the water pumps and turns it ON and OFF with respect to the level in the water tank. This auto-switching feature saves manpower. Hence no need to operate manually. There for no wastage of water, stop tank overflow, save water & electricity bill.

Features:

• Auto start &stop according the tank level
• Digital display to show level (in percentage)
• Audio alarm on full tank
• Push button to reset buzzer
• Maintenance free, high quality magneticfloat sensor
• It is suitable for 1/ 3 phase motor.

Our team of quality analysts strictly tests each product against varied quality parameters ensuring zero defects at buyer\'s end. Be it online payment or offline, we make possible for you to make trade transactions as per your convenience. We offer both offline and online mediums to make payment.Automatic Battery Charger for charging generator battery automatically with LED indications and fault protections.

Features :

\n
• Trickle and boost mode
\n
• Reverse polarity protection
\n
• Auto cut-off on full charge
\n

Availability

\n
• Transformer Base Battery Charger : 12/24 VDC   
\n
• SMPS Base Battery Charger : 12/24 VDC
\n

SUBTECH series UPVC plastic butterfly valve according to the different medium has a variety of optional material; corrosive resistance is strong, small volume, light weight, extremely non-toxic material. The Mid Stem Structure in this butterfly valve will protect the water leakage from butterfly valve to motor. It is used in industries, multi storied buildings, malls to control the flow of liquids.

Features :

• Can be operated automatically, manually or remotely
• Epoxy resin coating over mid stem structure prevents structure from corrosion.
• Operating Voltage - 130V to 280V.
• Maintenance free
• Can be used for any type of liquid.
• Size - 500mm to 300mm