Post Buy Requirement
Jodhpur, Rajasthan, India
Add Review

Shot Blasting Machine

Airless Shot Blasting Machine

Surfex Airless Shot Blasting Machine Rotary Barrel Type
Surfex Airless Shot Blasting Machine Rotary BarrelType complete with Elevator, Abrasive Recycling System, Control Panel, Electric Motors, Fabric Bag Type Dust Collector Unit, Capacity 1200 Cfm. with Load Carrying Capacity175 Kg.
Operating Principle :
The machine consists of Rotary Barrel lined with perforated rubber sheet. The barrel is loaded with components. The barrel rotate at low rpm and gently tumble components. A powerful Blast Wheel Unit is fitted at the bottom of barrel which fires shot on tumbling components and blast them thoroughly. The door of barrel is opened and blasted components are taken out.


The machine is fully ventilated by Dry Type Fabric Bag Dust Collector. The machine is recommended for small to medium size components.


Leading Technical Specification:
Note: Above specifications are subject to change due to continuous development of product.

Description SASMTF 20″X27″ SASMTF 27″X36″
Tumbler (Basket) Size 20″ x27″ 27″ x 36″
Size of Wheel (Diameter x Width) 300mm x 63mm 381mm x 63mm
No. of Wheels One One
     
Work Load Capacity    
Volume (Cubic Feet) 2 5
Weight (Kgs) 140 350
H.P. of Blast Wheel 7.5 15
Shots Flow Rate (Kg/Hr) 6500 12000
Type of Dust Collector Fabric Bag Fabric Bag
Dust Collector Capacity 1200 cfm 2000 cfm
Shaking Of Bags Manual Mechanical
Total Power Consumption 12.5 24
     
Dimension of Machine    
Length 1200 mm 1450 mm
Width 970 1310
Height 2460 3700
     
Floor Space required for Machine with Dust Collector    
Length 2950 mm 3400 mm
Width 3100 mm 3000 mm
View Complete Details

Diabolo Shot Blasting Machine

SURFEXintroduced low costShot Blasting Machine for cleaning of Rods / Bars. The use of this machine is recommended for replacing acid pickling process which is environmentally hazardous hence banned byCentral Pollution Control Board (CPCB) of India. The Machine is provided with singleBlast WheelStation mounted onBlast Cabinet. The Dia-Bola type of conveyor system is provided for rotating as well as moving forward the Rods / Bars. The Rods are fed on dia-bola which convey the same intoBlast Chamber, there it isshot blast/ cleaned. The blast / cleaned Rods come out from outlet side of blast cabinet. The machine is continuously operating single rod process system. The production rate upto 4 to 5 per meter per minute can be achieved. The machine can also be provided for feeding 2 rods at a time, hence output is doubled. The machine is equipped with effective shots recovery & cleaning system anddust collectorconform to Central Pollution Control Board (CPCB) norms. The entire operation of machine is controlled by control panel.

View Complete Details

PLATE PRESERVATION LINE

  • Pit Requirement 1070mm
  • Total Power Required 223.5 HP (166 kw)
  • Blast Wheel 20 HP x 6 120 (89 KW)
  • Dust Collector 30 HP x 1 30 (22 KW)
  • Bucket Elevator 12.5 HP x 1 12.5 (9.3 KW)
  • Long Screw conveyor 5 HP x 1 5 (3.73 KW)
  • Cross screw conveyor 3 HP x 1 3 (2.2 KW)
  • Upper screw conveyor3 HP x 1 3 (2.2 KW)
  • Roller Conveyor7.5 HP x 2 15 (10 KW)
  • Blow-off fan 15 HP x 2 30 (22 KW)
  • Brush off system 5 HP x 1 5 (3 KW)

It helps marine industries by providing inline Surface Treatment Systems (STS) in preservation Line, which removes contaminants, profiles the surface & coats the primary paint on blasted surface immediately after blasting operation without much loss of time, which will not allow any chances of oxidation of the ferrous plate generates high safety factor of corrosion protection against sea high humidified & salty weather.

View Complete Details

Concrete Surface Shot Blasting Machine

This machine is walk behind type, portable heavy duty self contained Shot blasting machine for surface preparation of plane surface, structure, concrete repair and restoration, general construction surface preparation prior to painting and coating, applying resin and tiles, to remove old coatings and rubber from roads and air port runways, asphalt cleaning etc. just to mention a few. The machine houses small size blast wheel to direct media at high velocity on the surface to be cleaned. The spent abrasive is recollected through vacuum pickup system inbuilt in the machine. The machine provides dust free working environment. The machine is easy to transport and use.
Model ASB-FB-101DT
Technical Specification

Working width 270mm
Blasting capacity Up to 150m²/h on concrete
Motor 11kW / 380V – 50Hz      / 22A – Three phases
Dimensions(LxWxH) 1880mm X 400mm X1060mm
Drive system/Speed Electric /0-25m/min
Mode of operation Horizontal movable self-propelled Backward(pull)
Surface Steel/Concrete/Stone/Asphalt
Accessories
Suction hose Diameter150mm X Length20m
Dust collector Motor 6.2kw
Airflow 1250m³/h
Dimensions(LxWxH) 1860mmX880mmX1450mm
View Complete Details

Hanger Shot Blasting Machine

HANGER TYPE SHOT BLASTING MACHINE Where component will be hanged and can be rotated, the Hanger Type Machine is advised. In this machine hanger are mounted on the doors of the machine. For the blasting operation the door of the machine is opened and components are loaded on to the hanger. Then the door is closed and the blast wheel unit is operated. Two Nos. of blast wheel stations are located strategically around the cabinet fires abrasives on rotating components. The components are shot blasted homogeneously all around on the rotating hanger and blast clean the components. After the blast cleaning cycle is over, the blast wheel is shut off and door is opened for unloading of components.


The machine is available in different capacities. Continuous Hanger Type Machine is also available.

Description ASH-1 ASH-2 ASH-3 ASH-4 ASH-5 ASH-6 ASH-7 ASH-8
No. of Blast wheel 2 2 2 2 2 2 2 2
Size Of Blast Wheel 12.5″ 12.5″ 12.5″ 12.5″ 12.5″ 12.5″ 12.5″ 12.5″
Flow Rate Hr/Wheel 3000 3000 5000 3000 5000 3000 5000 5000
H.P. Of Blast Wheel 5 5 7.5 5 7.5 5 7.5 7.5
Load Carrying Capacity of Hanger 300gm. 300gm. 300gm. 300gm. 300gm. 300gm. 300gm. 300gm.
R.P.M. of Hanger 6-12 6-12 6-12 6-12 6-12 6-12 6-12 6-12
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • K. K. Modi (Surface Finishing Equipment Co.)
  • E-100, Marudhar Industrial Area, Phase Ii, Basni, Basni, Jodhpur, Rajasthan - 342005, India
  • Share us via