Our Products #3034845

Velvet Paints is a dynamic, focused and rapidly emerging medium sized professionally managed non aligned company, with core competencies in Paints & Lime manufacturing. We believe that howsoever small our products may be, they act as a vital bridge leading to a great success for customers in terms of their excellence in technology and business. We are a responsible care company and concerned with the well being of customers, suppliers, employees, society and stakeholders.

Touch Acrylic Emulsion is made of unique forms of co-polymers and pigments available. These ingredients along with exclusive additives provide an optimum dispersion level. It gives a rich matt effect and gives a superior covering when applied for interior and exterior walls with stain guard technology.

Application Data

Surfaces to be painted suitable for all smooth plastered surfaces and designed brickwork, wooden surfaces, plywood's, asbestos cement sheets hard and soft boards, etc.

Primers

Touch cement primer (Solvent or Water thinnable). 1 coat on previously painted surfaces. 2 coats on new or unpainted surfaces. Putty filled areas should be touched up with a coat of Touch cement primer. Methods of Application Brush or roller. Finishing 2 or 3 coats Touch acrylic emulsion on primed, smooth surface only. Allow minimum 4 to 6 hours drying time between coats. Product Data Viscosity: 133 poise - a semi-liquid paint. Shades: As per Touch shade card. Packs: 1, 4, 10 & 20 litres. Finish: Smooth with a slight sheen. Covering capacity: 20 to 25 sq. meter per coat depending on the surface and shade. Thinner: Water CAUTION :Do not more than 50% water by volume.

A specially formulated acrylic co-polymer emulsion based distemper for elegant, smooth, durable, matt finish interiors. Application Data Surfaces to be painted Plastered interiors and ceilings. Primers Touch Cement Primer (Solvent or Water thinnable). NOTE:For smooth and level surfaces the use of Acrylic and Cement Putty is recommended for best results. Methods of Application Brush

Finishing

Add water slowly to the distemper paste, mixing the contents thoroughly. Continue thinning to application consistency. The normal mixing ratio is 2 parts of water to 3 parts of by volume for the 1st coat. For the 2nd coat the mixing ratio should be 1:1 by volume. Dry overnight between coats. Maximum overcoating interval - 48 hours.

Product Data

Viscosity: 4010 poise Shades: As per Touch shade card. Packs: 1 kg pouch pack, 5, 10 & 20 Kgs. Finish: Smooth and Matt. Covering capacity: 10 to 12 sq. metres per kg per coat depending on the surface and shade. Thinner: Water CAUTION :Do not add more than 65% water by volume.

Velvet wall putty is white cement based fine powder which provides an ideal finishing for concrete cement plastered walls and ceiling. Application DataSurfaces to be painted.New surface requires preparation such as removal of dust, dirt and foreign matter, In cases of cracks, voids & damages it should be repaired. If surface plaster was rough, 1st apply white cement white cement mortar and level the surface. cure the surface for 2 days. before starting putty coat. surface should be in just-wet condition, prior to putty application.

Use spatula blade trowel on the wall with "bottom to top" configuration. Apply second coat preferably after 4 hrs in hot season & after 12 hrs in cold season. Second coat shall be applied "horizontally" to even out application marks of 1st coat if any. Re-mix putty paste again for 1 minute, if it is left un-disturbed for 30 minutes. Allow complete drying for 3 days and then use fine emery paper to remove application mark, if any.

Velvet wall putty is white cement based fine powder which provides an ideal finishing for concrete / cement plastered walls and ceiling. Application Data Surfaces to be painted. New surface requires preparation such as removal of dust, dirt and foreign matter, In cases of cracks, voids & damages it should be repaired. If surface plaster was rough, 1st apply white cement/ white cement mortar and level the surface. cure the surface for 2 days. before starting putty coat. surface should be in just-wet condition, prior to putty application. CAUTION :Not recommended over lime wash. Primers Not required.

Methods of Application

Mix Velvet wall putty slowly in 35-40 % water by volume to prepare paste of desired consistency. Mix vigorously for 5-10 minutes for making lump free and uniform paste. Product should be mixed in such quantities that is could be used within 2 hrs of its preparation. Mixing could be done manually or by suitable electric mixer.

Finishing

Use spatula /blade/ trowel on the wall with "bottom to top" configuration. Apply second coat preferably after 4 hrs in hot season & after 12 hrs in cold season. Second coat shall be applied "horizontally" to even out application marks of 1st coat if any. Re-mix putty paste again for 1 minute, if it is left un-disturbed for 30 minutes. Allow complete drying for 3 days and then use fine emery paper to remove application mark, if any.

Velvet Choona is the cost effective and out standing result of used to you another choona. In presence of velvet Choona (lime+glue) to be test of our laboratory and define the quantity ratio of choona (lime) and binder. It is the stop remove the wall of choona. It is completely ready to use and not necessary to filtrate and wetting before a day. Velvet choona is not harmful to your hand. More capacity of surface covered with the help of Tio2. Application DataSurfaces to be painted.To remove the fungus, dust, mud or old removable flexes particle of your wall with the help of weir brush or emery paper.

Velvet water proof effectively increases cement density making the construction totally watertight and free from cracks. It is extensively used to make concrete basement impermeable for water tank, reservoirs walls, roofing, sewer, bathroom, tiles stucco etc. velvet waterproof is free from chloride.

Application Data

1 Bag of cement (50kg) requires only 1 kg of velvet waterproof similarly 1 ton of cement require just 20 kg of velvet waterproof. Do not add more than 1 kg of velvet water proof to a 50 kg bag of cement. For best results, mix just 2% in ordinary Portland cement. Methods of Application Mix thoroughly with cement by hand before adding sand and water. A through mix is essential for a perfectly dense mix. It dose not in any way interfere in the curing and setting time of the concrete.