Scissors

Our product range contains a wide range of Variable Rake Angle Hydraulic Shears, Portbale Electric Shears and Universal Hand Shear

Variable Rake Angle Hydraulic Shears

Ram & Table designed with inclined member and box type structure for maximum strength.
Positive holding of Hyd. Hold downs avoids slippage of sheet during cutting stroke.
HCHCr Blade suitable to MS & SS.
Hardened Transfer bars.
Front gauging by disappearing stoppers mounted on front squaring arm.

SPECIAL FEATURES

The stable robust, all welded steel frame from ultrasonically tested plates are of top quality. Ramand table designed with special inclined member and box type structure for maximum strength.
Thetopbeamisguidedbythreepointrollerwithreplaceablehardenedlinersforleastwear.Thiseliminates lubrication of guides. Roller guide made of hardened & ground bearing steel to provide better quality of cutting for a long time.
Rake angle can be varied to permit shearing of higher thickness than nominal capacity and facilitating distortion free shearing of thin sheets.
The fastest and easiest way of blade clearance setting without need of feeler gauge, which helpsBurr-free edges.
Positive holding by hydraulic holddowns before shearing avoids slippage of sheets and independent operation of holddowns for clamping of sheet helps checking of mark without taking shear stroke.
Front gauging by disappearing stoppers mounted on left squaring arm. Robust, heavy & accurateback gauging to set cutting width.
Hydraulic cylinder are designed with both low and high pressure sealing, Hard chrome plated rod also with special type guide for long life without leakage.
Hydraulic components of international quality assembled in our own factory with specially designed compact manifold

STANDARD ACCESSORIES

Main Drive motor
Electric Control Panel
Operational Console
Pre selector switch to adjust rake angle
Lever operated blade clearance with calibration
Fine stroke adjustment rod with limit switch
Front sheet support
Squaring arm on right end with steel rule
Hardened transfer bar mounted on table
Hold down cylinders
Shadow light Indicator
Four edge HCHCR / HCSR blade interchangeable & suitable to shear mild and St. Steel
Manual back gauge

OPTIONAL ACCESSORIES

Second squaring arm on left side
Motorised back gauge with DRO
NC back gauge with ball screw
Front support with rolleraccording to required length
Rear sheet support
Ball transfer table
Degree protector for angular cutting
Stroke counter
Design with throat depth
First fill of hydraulic oil

SPECIFICATIONS FOR VARIABLE RAKE ANGLE HYDRAULIC SHEARING MACHINES

Model	Cutting Length mm	Shearing Capacity Thickness mm				Nominal rake a angle	Rake angle range	Stroke per min.		No. of Holddowns	Holding Force Kgs.	Power H.P.	Packing Dimensions mm (LxWxH)	Approx. Weight Kgs
		M.S.		S.S.				Min. rake angle	Max. rake angle
		Nominal rake	Max. rake angle	Nominal rake	Max. rake angle
AMI 320	2000	3.15	4	2	3.15	1°15'	0.5-3°	20	11	11	2000	3	3200x1850x1950	3100
AMI 325	2500	3.15	4	2	3.15	1°15'	0.5-3°	25	13	13	2300	5	3200x1850x1950	3500
AMI 330	3000	3.15	4	2	3.15	1°15'	0.5-3°	21	9	16	2600	5	3700x1850x1950	4000
AMI 340	4000	3.15	4	2	3.15	1°15'	0.5-3°	12	6	22	3200	7.5	4700x1950x2050	5500
AMI415	1500	4	6	3	4	1°37'	0.5-3°	25	13	8	4500	7.5	2250x1850x2050	3200
AMI 420	2000	4	6	3	4	1°37'	0.5-3°	23	11	11	6200	7.5	2750x1850x2050	3500
AMI 425	2500	4	6	3	4	1°37'	0.5-3°	21	8	13	8000	7.5	3300x2250x2400	5000
AMI 430	3000	4	6	3	4	1°37'	0.5-3°	21	10	16	10000	10	3700x2250x2400	6000
AMI 440	4000	4	6	3	46	1°37'	0.5-3°	20	6	20	12000	10	4500x2250x2400	8100
AMI 615	1500	6	8	4	6	1°45'	0.5-3°	22	8	8	6500	10	2250x1900x2100	4000
AMI 620	2000	6	8	4	6	1°45'	0.5-3°	20	7	11	6500	10	2750x1900x2100	4300
AMI 625	2500	6	8	4	6	1°45'	0.5-3°	24	8	13	8500	15	3300x2250x2500	6000
AMI 630	3000	6	8	4	6	1°45'	0.5-3°	22	6	16	10800	15	3800x2250x2500	7200
AMI 640	4000	6	8	4	6	1°45'	0.5-3°	24	6	20	13600	20	4800x2250x2500	9000
AMI 815	1500	8	10	6	8	2°	0.5-3°	15	8	8	10500	10	2250x2050x2200	4500
AMI 820	2000	8	10	6	8	2°	0.5-3°	18	8	11	12000	15	2750x2050x2200	5500
AMI 825	2500	8	10	6	8	2°	0.5-3°	20	8	13	16500	20	3300x2350x2600	7500
AMI 830	3000	8	10	6	8	2°	0.5-3°	18	6	16	18500	20	3800x2350x2600	9600
AMI 840	4000	8	10	6	8	2°	0.5-3°	18	8	20	23000	30	4800x2350x2600	12500
AMI 1015	1500	10	13	8	10	2°	0.5-3°	14	6	8	10500	10	2250x2050x2300	5200
AMI1020	2000	10	13	8	10	2°	0.5-3°	18	8	11	13000	15	2750x2050x2300	6000
AMI 1025	2500	10	13	8	10	2°	0.5-3°	15	8	13	17500	20	3300x2500x2800	7500
AMI 1030	3000	10	13	8	10	2°	0.5-3°	12	6	16	20000	20	3800x2500x2800	10000
AMI 1040	4000	10	13	8	10	2°	0.5-3°	13	6	20	25000	30	4800x2500x2800	14000
AMI 1320	2000	13	16	10	13	2°	1-3°	15	8	11	16000	25	2850x2500x2700	7000
AMI 1325	2500	13	16	10	13	2°	1-3°	13	6	13	20000	25	3350x2600x2800	8500
AMI 1330	3000	13	16	10	13	2°	1-3°	11	6	16	25000	25	3800x2600x2800	11000
AMI 1340	4000	13	16	10	13	2°	1-3°	9	4	20	25000	30	4850x2200x2800	15500
AMI 1620	2000	16	20	13	16	2°	1-3°	18	6	11	20000	30	3000x2500x2800	11000
AMI 1625	2500	16	20	13	16	2°	1-3°	15	5	13	25000	30	3500x2600x2900	15000
AMI 1630	3000	16	20	13	16	2°	1-3°	12	5	16	28000	30	4000x2600x2900	17000
AMI 1640	4000	16	20	13	16	2°	1-3°	9	4	20	30000	30	5100x2750x2900	20000
AMI 2025	2500	20	25	16	20	2°	1-3°	12	5	13	28000	40	3500x2750x3000	18000
AMI 2030	3000	20	25	16	20	2°	1-3°	11	5	16	35000	40	4000x2750x3000	20000
AMI 2040	4000	20	25	16	20	2°	1-3°	9	4	20	40000	50	5100x2800x3000	24000
AMI 2525	2500	25	30	20	24	2°	1-3°	10	4	16	36000	60	3600x2900x3000	25000
AMI 2530	3000	25	30	20	24	2°	1-3°	8	4	18	45000	60	4000x2900x3200	28000
AMI 2540	4000	25	30	20	24	2°	1-3°	7	4	20	50000	75	5100x2900x3200	32000

View Complete Details

Ask Latest Price & Details

Portbale Electric Shears

Country of Origin 220 V
Model No. AMI-3
Maximum shearing capacity 3 mm (1/8")
Number of shear strokes at max. load 900 per min.
Number of shear strokes unloaded 1000 per min.
Shearing/cutting speed 2 Mtr. per Min.
Nominal input 550 watts.
Weight (Approx.) 6.8 Kgs.

The portable electric shear model 'AMI-3' is very useful and an indispensable tool in all workshops, assembly line, erection sites, coach building shops, tin smith and alike industries as it is handy, convenient and easily accessible to different types of shearing jobs in various materials upto 3 mm thickness (in M.S. with tensil strength 45kg sqr. mm.) for straight, round, ovel, curved and/or irregular shapes at rapid speed reducing thereby the production and maintanance cost considerably.

A moving cutter moves against a stationary one in the anvil. The cutting speed is high and there is no loss of material. While a shear can be used for splitting sheets where the resistance to bending is not great, they are not recommended for cutting across wide and thick plates. On heavier gauges of material they should be regarded as trimming shears, main portion remaining flat; while the cut portion is bent away beneath the anvil.

The anvil is designed so that scribed lines are well in view and are easily followed allowing straight lines and curves to be easily cut. The minimum cutting radius is approximately 3.1/2lnch. Blades are of special die steel and are of simple design. They are of sufficient length to stand fro 10 to 15 grindings. The motor is forintermitentoperationand is of fan cooled type, suitable for operation on AC. 220 volts, single phase, 50 cycles with built-in "ON" "OFF" Switch, 2 meter long cable and plug.

Extra accessories:

Spare blade
Carbon brush

View Complete Details

Ask Latest Price & Details

Universal Hand Shear

Heavy duty hand operated geared shearing machine suitable for cutting sheets in unlimited length, round or square bars, angle, 'T' etc. complete with handle.

SPECIFICATIONS

Model No.		AMI 8CH	AMI 10CH
Cuts in unlimited lengths
Mild steel plates upto	mm	8	10
Flat upto	mm	50 X 12	75 X 13
Round upto	mm	18	24
Square upto	mm	18	24
Tee cutting capacity	mm	55 x 5	60 x 6
Angle cutting capacity in one cut	mm	62 x 6	75 x 7
Length of blade (approx.)	mm	175	175