Analytical Electronics Services Pvt Ltd

Gandhinagar, Gujarat

PicoScope 9300 Series -Sampling Oscilloscopes to 25 GHz with TDR/TDT and Optical models15 to 25 GHz electrical, 9.5 GHz optical, TDR/TDT, 2-channel and 4-channel, compact, portable, USB instruments.
These units occupy very little space on your workbench and are small enough to carry with your laptop for on-site testing, but thats not all. Instead of using remote probe heads attached to a large bench-top unit, you can position the scope right next to the device under test. Now all that lies between your scope and the DUT is a short, low-loss coaxial cable. Everything you need is built into the oscilloscope, with no expensive hardware or software add-ons to worry about.
Key specifications-15 TS/s (64 fs) sequential sampling-Up to 15 GHz prescaled, 2.5 GHz direct trigger and 11.3 Gb/s clock recovery-Industry-leading 16-bit 1 MS/s ADC and 60 dB dynamic range-Eye and mask testing to 16 Gb/s with up to 2231 pattern lock-Intuitive, touch-compatible Windows user interface-Comprehensive built-in measurements, histogramming and editable data mask library-Integrated, differential, deskewable TDR/TDT step generator
Typical applications:-Telecom and radar test, service and manufacturing-Optical fiber, transceiver and laser testing-RF, microwave and gigabit digital system measurements-Radar bands I, G, P, L, S, C, X, Ku-Precision timing and phase analysis-Digital system design and characterization-Eye diagram, mask and limits test to 10 Gb/s-Ethernet, HDMI 1, HDMI 2, PCI, SATA, USB 2.0, USB 3.0-TDR/TDT analysis of cables, connectors, backplanes, PCBs and networks-Optical fiber, transceiver and laser test-Semiconductor characterization
Trigger modes:2.5 GHz direct and up to 15 GHz prescaled trigger:Sampling oscilloscopes accept their trigger from a separate input, either directly for repetition rates up to 2.5 GHz or via a prescaling divider input, for repetition rates up to 15 GHz (14 GHz on 15 and 20 GHz models).
Built-in 11.3 Gb/s clock data recovery trigger:To support serial data applications in which the data clock is not available as a trigger, or for which trigger jitter needs to be reduced, the PicoScope 9302 and 9321 include a clock recovery module. This continuously regenerates the data clock from the incoming serial data or trigger signal and can do so with reduced jitter even over very long trigger delays or for pattern lock applications. A divider accessory kit is included to route the signal to both the clock recovery and oscilloscope inputs.
9.5 GHz optical model:The PicoScope 9321-20 includes a built-in precision optical-to-electricalconverter. With the converter output routed to one of the scope inputs(optionally through an SMA pulse shaping filter), the PicoScope 9321-20 can analyze standard optical communications signals such as OC48/STM16, 4.250 Gb/s Fibre Channel and 2xGB Ethernet. The scope can perform eyediagram measurements with automatic measurement of optical parameters including extinction ratio, S/N ratio, eye height and eye width. With its integrated clock recovery module, the scope is usable to 11.3 Gb/s.
The converter input accepts both single-mode (SM) and multi-mode (MM)fibers and has a wavelength range of 750 to 1650 nm.
TDR/TDT analysis

PicoConnect 900 Series: the shape of probes to come:The PicoConnect 900 Series is a range of low-invasive, high-frequency passive probes, designed for microwave and gigabit applications up to 9 GHz and 18 Gb/s. They deliver unprecedented performance and flexibility at a low price and are an obvious choice to use alongside the PicoScope 9300 Series scopes.Features of the PicoConnect 900 Series probes
PicoSource PG900 Series differential pulse generators:For greater versatility than a built-in signal generator can offer, you may want to separate your high-performance fast-step TDR/TDT pulse source from the sampling oscilloscope and have two instruments to use either stand-alone or together as required.

PT-104 Platinum Resistance Data Logger
The PT-104 is a four-channel temperature measuring data logger. It offers the ultimate in resolution (0.001 C) and accuracy (0.015 C). Along with temperature it can also be used to measure resistance and voltage
- Measures temperature, resistance and voltage- High resolution and accuracy- Works with PT100 and PT1000 sensors- Supports 2, 3 and 4-wire sensors- No power supply required- USB and Ethernet interfaces- Run multiple units on a single PC

Accuracy and resolution:Although accurate temperature sensors are widely available, it has been difficult to take advantage of them due to errors caused by the measuring device. Your PT-104, however, is inherently accurate due to its innovative design. Rather than relying on voltage references, which tend to be temperature-sensitive, it uses reference resistors, which are extremely stable with low temperature coefficient and drift. The exact value of each resistor is stored in an EEPROM to provide the ultimate in accuracy (yearly recalibration is recommended). A high-performance 24-bit ADC is used to achieve the 0.001 C resolution.
Temperature:
The PT-104 measures temperature using platinum resistance thermometers (PRTs). Both common industry standards (PT100 and PT1000) are supported. The unit is compatible with two, three and four-wire sensors (four-wire PT100 sensors are recommended for accurate measurements). A wide range of PT100 sensors are available for use with your PT-104.
Voltage
For voltage measurements, each input connector can be treated as a differential input with ground, or two single-ended inputs. Both inputs must be zero volts or above, though it does not matter which input has the higher voltage.
Two voltage ranges are available (0 to 115 mV and 0 to 2500 mV). For the most accurate measurements use the 0 to 2500 mV range.Resistance
When measuring resistance, the PT-104 uses a four-wire circuit to give the greatest possible accuracy. Two resistance ranges are available (0 to 375 and 0 to 10, 000 ). The unit is calibrated for 0 to 375 so this range should be used for accurate measurements.Single channel screw terminal adaptor
Interfacing third-party sensors not fitted with the 4-pin mini-DIN connector or measuring voltage or resistance is possible using the PP660 screw terminal adaptor. This inexpensive adaptor has 4 breakout terminals and occupies a single channel of the PT-104.
But I need to measure more channels
The PT-104 is capable of measuring up to 4 channels at once. Need more channels? No problem. Using PicoLog you can connect up to 20 PT-104s to one PC giving you a potential 80-channel PT100 data logger. Alternatively you can use your PT-104 logger with up to 19 other Pico data loggers, such as the PicoLog 1000 multichannel data logger, to create your own custom data acquisition system
The ultimate in portability
With both USB and Ethernet interfaces, the PT-104 can be used in a variety of situations. If you need a portable solution that can be used at various locations and is fast to set up and use, simply connect your laptop to the PT-104 by USB. Need to monitor a situation over a period of hours or days, or from a remote location? Plug your PT-104 into a spare port on your network and then access it remotely either from your LAN or over the internet. Using Power over Ethernet (PoE) technology means that you dont even need a separate power supply. Please note that PicoLog 6 data logging software only supports Ethernet connection in Windows.

USB TC-08 - 8 channel thermocouple data loggerTemperature measurement and recording with the TC-08 is very easy simply plug the TC-08 into a USB port on your computer, plug in your thermocouples, and you are ready to go.
Building on the proven design of PicoLog 6, PicoLog Cloud is a free upgrade that introduces many great new features that expand how your Pico data logger can be used.
PicoLog Cloud allows all current Pico data loggers and real-time scopes to capture data directly to our new free Cloud service, and can be shared via a link to any browser on a PC, phone or tablet, anywhere in the world. In addition, an API can be used that allows live capture data to be transferred from the Cloud to a 3rd party database or program.

- 8 channel thermocouple data logger- Measures from 270 to +1820 C (454 to +3308 F)- High resolution and accuracy- Expandable to 20 units / 160 channels- Supports all popular thermocouple types- Fast sampling rate up to 10 measurements per second (including CJC)- USB connected and powered- PicoLog 6 for Windows, macOS and Linux data logging software included- PicoSDK drivers for Windows, macOS and Linux included
Wide temperature range:The TC-08 thermocouple data logger is designed to measure a wide range of temperatures using any thermocouple that has a miniature thermocouple connector. Pico supply a wide range of suitable thermocouples (see Accessories).
All popular types of thermocouple are supported, allowing an effective temperature range of 270 to +1820 C (the actual temperature range depends on the thermocouple being used).
The built in Cold Junction Compensation (CJC) circuit can also be used as a 9th channel to measure room temperature.
Fast and accurate temperature data acquisition:
With the TC-08 thermocouple data logger your temperature measurements can be made both fast and accurately.
The short conversion time of the TC-08 means up to 10 temperature measurements can be taken every second (cold junction compensation counts as an additional measurement), while the high (20-bit) resolution ensures that the TC-08 can detect minute changes in temperature. For popular Type K thermocouples the TC-08 can maintain a better than 0.025C resolution over a 250 to +1370 C range.

Also measure voltage and 420 mA current loops! :
As well as measuring temperature with thermocouples, the terminal board allows other sensors with voltage or current outputs to be connected.
The optional Single-Channel Terminal Board (see Accessories) plugs into a channel on the TC-08 and turns it into a 20-bit high resolution data logger. Screw terminals allow wires to be attached to the data logger without soldering. The four input ranges (50 mV, 500 mV, 5 V and 4-20 mA) allow a wide range of other sensors and signals to be measured.