Gandhinagar, Gujarat, India
Verified
Add Review
Our Products
Digital display high voltage amplifier. AMPL times, current, voltage are diplayed on the pannel. It also add more protection design. More humanizepractical.
| Model | HA-820A | ||
| Output | |||
| Output DC Voltage(Max.) | 400V DC | ||
| Output AC Voltage(Max.) | 800Vp-p | ||
| Output DC Current(Max.) | 100mA DC | ||
| Output AC Current(Max.) | 200mAp-p | ||
| Output Power(Max.) | 40 VA | ||
| Bandwidth | DC-400KHz(-3dB) | ||
| Slew rate(Typ.) | 500V/us | ||
| Output Resistance (Protection SW OFF) | 10 | ||
| Output Resistance (Protection SW ON) | 5K/40watt | ||
| Max. Loading value | 4K@Range400V;2.5K@Range250V | ||
| Input (normal/Max.) | 5V(Max.10V) | ||
| AMPLtimes | 100(Max) | ||
| DC OFFSET(2 options with 2 Rout) | 250V/ 400V | ||
| Monitor(Output ratio) | 1001 | ||
| Protection | 1.Output used FUSE 2.Protection SW protection resistance(ON/OFF) 3.Output short circuit, overload, over current, over voltage protection 4.INPUT/OUTPUT overload protection 5.Overheating protection | ||
| Measuring display(01MHz) | |||
| Range | Resolution | Accuracy | |
| Max. voltage | 400V | 0.1V | (1%+2V) |
| Min. voltage | 400V | 0.1V | (1%+2V) |
| Peak to peak voltage | 0800.0V | 0.1V | (1%+2V) |
| Offset voltage | 400V | 0.2V | (1%+0.4V) |
| Output current | 0100.0mA | 0.1mA | 1% |
| Setting | |||
| AMPL times | 0100.00 | 0.05 times | - |
| Output bias | 400V | 0.2V | 1% |
APA5200A series high power AC power supply IGBT/SPWM Pulse Wave width adjustment mode Terminal Voltage feedback compensation function ensures no error in test power can set the waveform starting angle (0-359), with synchronous source signal interface Select-able voltage Analog (0-5V) or current analog (4-20mA) control of power output Using a single chip microcomputer (d/a circuit) to collect voltage and current waveform data directly interface rs232/rs485 is optional, communication with computer CPU design to control the logic circuit opening and closing, one to one drive.
| Model | APA5215A | APA5220A | APA5230A | APA5260A | APA52100A | ||
| Power | 15KVA | 20KVA | 30KVA | 60KVA | 100KVA | ||
| Working | SPWM( Sinusoidal Pulse Width Modulation) | ||||||
| INPUT | Phase | 34W | |||||
| Voltage | 380V10% | ||||||
| Frequency | 47Hz 63Hz | ||||||
| OUTPUT | Phase | 34W | |||||
| Voltage | 0-150VAC / 0-300VAC AUTO | ||||||
| Frequency | 45-120Hz(40-500Hz optional)0.1Step | ||||||
| Max Current | L=120V | 42A | 56A | 84A | 168A | 278A | |
| H=240V | 21A | 28A | 42A | 84A | 139A | ||
| Display | VrmsArmsFreWattagePF | ||||||
| Line Regulation | 0.10% | ||||||
| Load Regulation | 1% | ||||||
| T.H.D | 2%(Pure resistive load) | ||||||
| Frequency Regulation | 0.01% | ||||||
| Voltage Resolution | 0.1V | ||||||
| Frequency Resolution | 0.1Hz | ||||||
| Current Resolution | 0.01A | 0.1A | |||||
| Accuracy | Voltage | 0.5%FS+5dgt | |||||
| Current | 0.5%FS+5dgt | ||||||
| Wattage | 0.5%FS+5dgt | ||||||
| Frequency | 0.01%FS+5dgt | ||||||
| Setting accuracy | Voltage | 1% | |||||
| Current | 0.10% | ||||||
| Memory | M1 (V_F_A)M2 (V_F_A) M9 (V_F_A) | ||||||
| Interface | RS232C IEEE488.2(GPIB) optional | ||||||
| I-LIM Set | O-Max Current | ||||||
| Protection | Over Current Over Temp Over Load Short Circuit | ||||||
| Weight(Kg) | 150 | 200 | 300 | 500 | 900 | ||
| Dimension WHD(mm) | 430700700 | 6109301050 | 70012001400 | ||||
| Environment | 0-40 20-80%RH | ||||||
PicoLog CM3 Current Data Logger
The PicoLog CM3 is a three-channel data logger that uses industry-standard current clamps. Simply connect to your PC via USB or Ethernet, run the supplied software and you can monitor and log current for a wide range of applications.
- High accuracy with 24-bit resolution- Suitable for single or three-phase AC currents - Optional 0 to 200 A AC current clamps- Can also be used to measure AC RMS voltage- Up to 20 units can be run on a single PC- Connected via Ethernet (PoE compatible) or USB- Uses free PicoLog 6 data logging software
Typical applications:- Mains current monitoring- Three-phase load balancing- Long-term energy use recording- Energy and cost saving / ISO14001 monitoring
Non-invasive current clamps:The PicoLog CM3 measures current using industry-standard AC current clamps. These clamps have opening jaws so can be installed in seconds with no physical connection to high voltages. AC current clamps require no power supply or batteries so are ideal for long-term energy-use monitoring and logging.
Pico supply 200 A AC current clamps as standard. If you need to measure higher currents we will be happy to advise on suitable clamps for your application.
The PicoLog CM3 is available on its own so you can add your own current clamps or as a cost-saving kit with three 200 A clamps included.
USB or Ethernet connection for local or remote logging:
With both USB and Ethernet interfaces your PicoLog CM3 can be used in a variety of situations. If you need a portable instrument that can be used at various locations and is fast to set up and use, simply connect your laptop to the PicoLog CM3 by USB. No external power supply is required as the CM3 is powered from the USB port.
Need to monitor a situation over a period of hours or days, or from a remote location? Plug your PicoLog CM3 into a spare port on your network and then access it remotely either from your LAN or over the internet. When using Ethernet the CM3 can be powered either by Power over Ethernet (PoE) or by using the USB connection just for power. Please note that PicoLog 6 data logging software only supports Ethernet connection in Windows.
PicoLog CM3 PicoLog 6 softwarePicoLog 6 data logging software for PicoLog CM3
PicoLog 6 is a complete data acquisition software package for the PicoLog CM3 current data logger. It provides a visual, easy-to-use interface allowing you to quickly set up simple or complex acquisitions and record, view and analyze data.
-Real-time data collection and display-Visual logger and channel setup for easy configuration and viewing-Available for Windows 7, 8 and 10 (32 and 64-bit), macOS, Linux and Raspbian for Raspberry Pi-Virtually unlimited logging capacity to PC-Robust database format minimizes data loss and corruption-Simple and complex programmable alarms- Up to 4 independent graph axes-Data can be exported as CSV, clipboard image and PDF-Supports multiple different PicoLog data loggers and PicoScope oscilloscopes on the same PC
PicoScope 5000 Series -FlexRes 8 to 16-bit hardware resolution USB Oscilloscope- FlexRes 8 to 16-bit hardware resolution- Up to 200 MHz analog bandwidth- 1 GS/s sampling at 8-bit resolution- 62.5 MS/s sampling at 16-bit resolution- Up to 512 MS capture memory- 16 digital channels on MSO models- 130 000 waveforms per second- Built-in arbitrary waveform generator- 18 serial decoding protocols as standard- Up to 200 MHz spectrum analyzer
Todays electronic designs employ a wide range of signal types: analog, digital, serial (both high- and low-speed), parallel, audio, video, power distribution and so on. All need to be debugged, measured and validated to ensure that the device under test is functioning correctly and within specification.
To handle this variety of signal types, PicoScope 5000D FlexRes hardware employs multiple high-resolution ADCs at the input channels in different time-interleaved and parallel combinations to optimize either the sampling rate to 1 GS/s at 8 bits, the resolution to 16 bits at 62.5 MS/s, or other combinations in between you select the most appropriate hardware resolution for the requirements of each measurement.
2 and 4 channel models are available, all featuring a SuperSpeed USB 3.0 connection, providing lightning-fast saving of waveforms while retaining compatibility with older USB standards. The PicoSDK software development kit supports continuous streaming to the host computer at rates up to 125 MS/s. The product is small and light, and operates silently thanks to its low-power fanless design.
Supported by the free-of-charge and regularly updated PicoScope 6 software, the PicoScope 5000D Series offers an ideal, cost-effective package for many applications, including design, research, test, education, service and repair.
High bandwidth, high sampling rate:Despite the compact size and low cost, there is no compromise on performance, with bandwidths up to 200 MHz. This bandwidth is matched by a real-time sampling rate of 1 GS/s, allowing detailed display of high frequencies. With a real-time sampling rate of five times the input bandwidth, PicoScope 5000 Series oscilloscopes are well equipped to capture high-frequency signal detail. For repetitive signals, the maximum effective sampling rate can be boosted to 10 GS/s by using Equivalent Time Sampling (ETS) mode.
Serial bus decoding and analysis:With its deep memory, the PicoScope 5000D Series can decode 1-Wire, ARINC 429, CAN and CAN-FD, DALI, DCC, DMX512, Ethernet 10Base-T and 100Base-TX, FlexRay, IC, IS, LIN, Manchester, MODBUS, PS/2, SENT, SPI, UART (RS-232 / RS-422 / RS-485) and USB 1.1 protocol data as standard.
Features
Test frequency: 10Hz-130MHz
High precision: using automatic balance bridge technology, four-terminal pair test configuration
High stability and consistency
High speed: the fastest test speed up to 5ms
High resolution: 10.1-inch capacitive touch screen, resolution 1280*800
Three test methods: point test, list scan, and graph scan
1601 point multi-parameter list scanning function
Four-parameter measurement
4-channel graphic scanning function, each channel can display 4 curves, 16 kinds of split-screen display modes for channels and curves
Powerful sorting: 10 grades sorting in LCR mode
Graphic scanning mode, each curve is sorted individually
High compatibility: Support SCPI instruction set, compatible with KEYSIGHT E4990A, E4980A, E4980AL, HP4284A
Applications
Passive component:
Impedance parameter estimation and performance analysis ofcapacitor, inductor, magnetic core, resistor, piezoelectric devices, transformers, chip components and network components
Semiconductor component
Parasitic parameter test and analysis of LED driver integrated circuitC-VDC features of varactors
Parasitic parameter analysis of transistors or integrated circuit
Other components
Impedance assessment of printed circuit boards, relays, switches, cables, batteries
Dielectric material
Dielectric constant and loss angle evaluation of plastics, ceramics and other materials
Magnetic materials
Magnetic permeability and loss angle assessment of ferrite, amorphous body and other magnetic materials
Semiconductor materials
Dielectric constant, electrical conductivity and C-Vcharacteristics of semiconductor materials
Liquid crystal cell
Dielectric constant, elastic constant and C-V characteristicsof liquid crystal cell
Specifications
| Model | TH2851-130 | |
| Display | 10.1 Inches TFT LCD Display 1280RGB800, Touch Screen | |
| AC Parameter | Cp/Cs, Lp/Ls, Rp/Rs, Z, Y, R, X, G, B, , D, Q, VAC, IAC | |
| DC Parameter | VDC, IDC, DCR | |
| Test Frequency | Range | 10Hz-130MHz |
| Resolution | 1mHz | |
| Relative frequency tolerance | 0.0007% | |
| Test Level | AC Voltage | 5mV2Vrms |
| Resolution | 1mV | |
| AC Current | 50uA20mArms | |
| Resolution | 10uA | |
| DC Bias | Voltage | 0V-40V |
| Resolution | 1mV | |
| Current | 0mA-100mA | |
| Resolution | 40A | |
| Test terminal configuration | Four Terminal Pair | |
| Output impedance | 25 / 100 | |
| Typical Test time(Speed) | Five Shift: 1(Fast)5(Accuracy)1: 2.5ms 2: 10ms 3: 40ms 4: 80ms 5: 400ms(Does not include the arithmetic average of the communication time, each frequency test speed will be slightly different) | |
| Max Accuracy | 1kHz: 0.08% | |
| 1MHz: 0.08% | ||
| 2MHz: 0.5% | ||
| 10MHz: 1% | ||
| 130MHz: 5.0% | ||
| Test Display Range | E means1, 000, 000, 000, 000, 000, 000 | |
| Cs, Cp | -9.99999EF -+9.99999EF | |
| Ls, Lp | -9.99999EH -+9.99999EH | |
| D | -9.99999E -+9.99999E | |
| Q | -9.99999E -+9.99999E | |
| R, Rs, Rp, X, Z | -9.99999E -+9.99999E | |
| G, B, Y | -9.99999ES -+9.99999ES | |
| Vdc | -9999V -+9999V | |
| Idc | -9999mA -+9999mA | |
| r | -999999rad -+999999rad | |
| d | -180.0deg -+180.0deg | |
| % | -999999%-+999999% | |
| Multi-function parameter list scan | 1601 points, each point can be set to average, and each point can be sorted separately | |
| Sweep parameters: measurement parameters, test frequency, AC voltage, AC current, DC BIAS voltage, DC BIAS current | ||
| Graphic scan | parameter | Frequency, ACV, ACI, DCV, DCI |
| Types | Logarithmic, linear, frequency segmentation | |
| Points | 2-1601 | |
| Number of channels | 4 | |
| Number of curves | 4 Per Channel | |
| Split Screen | 14 (Channel and Cruve) | |
| Equivalent circuit analysis | 3-element model: 4, 4-element model: 3 | |
| Sorting | 10 levels of sorting in LCR mode; each curve in scan mode is sorted individually | |
| Interface | RS232C, USB HOST, USB DEVICE, LAN, GPIB, HANDLER, VGA, HDMI | |
| Power-on warm-up time | 60 Minutes | |
| Input Voltage | 100-120VAC/198-242VAC Option, 47-63Hz | |
| Power consumption | Max 150VA | |
| Measurement WxHxDmm3 | 428x220x325 | |
| Weight | 14.5kg | |
PicoScope 6400E models 6824E 6424E 6804E 6404E 6403E- 8-bit to 12-bit FlexRes ADC- A choice of 4 or 8 analog channels- Add 8 or 16 digital MSO channels- Up to 500 MHz bandwidth- 200 ms capture time at 5 GS/s- Up to 4 GS capture memory- 50 MHz 200 MS/s 14-bit AWG- USB 3.0 interface- 300 000 waveforms per second update rate
- PicoScope 6 software and PicoSDK included- 21 serial protocol decoder/analyzers included- Mask limit testing and user-definable alarms- High-resolution time-stamping of waveforms- Over ten million DeepMeasure results per acquisition - Advanced triggers: edge, window, pulse width, window pulse width, level dropout, window dropout, interval, runt and logic
PicoScope 6000E Series oscilloscope pack contents:-PicoScope 6000E Series PC oscilloscope-P2056 500 MHz 10:1 passive probes (4)(supplied with the PicoScope 6824E, 6424E, 6804E and 6404E)-P2036 300 MHz 10:1 passive probes (4)(supplied with the PicoScope 6403E)-Quick start guide-12 V power supply, universal input-Localized IEC mains lead-USB cable, 1.8 m-Storage / carry case
TA369 MSO pod pack contents-TA369 8-channel MSO pod-MSO test hooks (pack of 12)-MSO ground lead (8)-MSO ground clip 1-way (8)-MSO ground clip 4-way-MSO ground clip 8-way-MSO digital interface cable-Storage / carry case
Accessories:PQ219 : 8-channel probe holder kit for PicoScope 6000E SeriesPQ215 : Probe holder kit, no probesTA437 : passive oscilloscope probe: 500 MHz 2.5 mm 10:1, BNC, single packTA480 : passive oscilloscope probe: 500 MHz 2.5 mm 10:1, BNC, dual packTA436 : passive oscilloscope probe: 300 MHz 2.5 mm 10:1, BNC, single packTA479 : passive oscilloscope probe: 300 MHz 2.5 mm 10:1, BNC, dual pack
The Radio Communications Test SetMarconi 2955Bprovide comprehensive test facilities for AM, FM and M mobile radio transceivers operating up to 1000 MHz. The 2955B is a combination of the following instruments:
These are automatically connected to the appropriate socket when an operating mode is selected. A large CRT display shows all the generated and measured information for each test and a direct indication of the control settings being used. The 2955B can be used to check a wide range of equipment including simplex and duplex radio telephones and mobiles using selective calling and cross-band repeaters.
Marconi / IFR 2955B Features
| ThePowerXplorer PX5integrates the most advanced feature set available in a power monitoring instrument, with an easy-to-navigate, color graphical user interface. With high-speed sampling and data capture (1 microsecond/channel), this 8-channel workhorse simultaneously captures and characterizes thousands of parameters, using a range of standard and customizable operating modes. The unique measurement capabilities of the PowerXplorer include capture of low-medium-high frequency transients through peak, waveshape, rms duration and adaptive high-speed sampling, as well as power measurements to clearly characterize non-sinusoidal and unbalanced systems. |
DranetzBMI PX5 PowerXplorer - Features
