Analytical Electronics Services Pvt Ltd

Gandhinagar, Gujarat

N1070A(7000Vp-p, 50MHz) high accuracy differential Probe

Introduce

Bandwidth: 50MHz Max. measuring voltage:7KVp-p Voltage overload protection Input impedance 10M//2pF each side ground Compatible with any brand's oscilloscope. 1% accuracy, compatible with any oscilloscope, standard BNC interface.

Model	N1070A
Bandwidth	DC-50MHz
Error	1%
Input impedance	20M//1 PF each side ground
Output voltage
-Swing(into 50 K load)	7V
-Offset(typical)	5Mv
-Input impedancetypical	50(for using 1M ohm input system oscilloscope)
Supply power
-external	power leads
BNC length	90cm
Test length	60cm
Weight	500g
Side (LWH)	245x84x36mm
Attenuation ratio	1:1000/100
CMRR(typical)	-80dB@60Hz, -50dB@100KHz
Maximum input differential voltageVp-p	7000V@1/1000 700V@1/100
DC + Peak ACVp-p	7000V@1/1000 1/100
CMRR	1000V rms CAT

14A-350000A Flexible current probe(14350000A5Hz-30MHz)

The flexible current probe is ideal tool for electronic power development. because its an equipment with the characteristic of easy using, small, flexible, accuracy, speedy and safety, it is available to all oscilloscope and digital meter . It can measure from small current to high current, and display the current on the oscilloscope, the Max. Bandwidth is 30MHz, is ideal for all aspects of Electronics Research and development.

Wide measuring range: bandwidth range:5Hz--30MHz, measuring current range:0.5A--350000A, No need to match other current transformer, is ideal for all aspects of e-research and development. Monitoring current waveforms for semiconductor switches, developing electronic power equipment, monitoring high frequency sinusoidal currents. Measuring fault currents terminal or short-circuit currents, analyzing harmonic current. Measuring and analyzing signal or earth leakage currents in 3-phase supply systems.

Instantaneous 7Vp-p output to plug directly into data acquisition equipment, DMM or power recorders.

Flexible current probe for AC current measuremnt.

Type	Sensitivity mV/A	Peak Current (A)	Min. Current ( A)	Noise (mV Pk-Pk)	Bandwidth (3db)	Accuracy	Coil Length	Line Length
DK-1400	5	1400	14	14	5Hz-30MHz	1%+3mV	300mm 1000mm	1m 4m
DK-3500	2	3500	35	10	5Hz-30MHz	1%+2mV
DK-7000	1	7000	70	8	5Hz-30MHz	1%+2mV
DK-14000	0.5	14000	140	5	5Hz-30MHz	1%+2mV
DK-35000	0.2	35000	350	5	5Hz-30MHz	1%+2mV
DK-70000	0.1	70000	700	5	5Hz-30MHz	1%+2mV
DK-140000	0.05	140000	1400	5	5Hz-30MHz	1%+2mV
DK-350000	0.02	350000	3500	5	5Hz-30MHz	1%+2mV
General characteristics
Coil cross section(Max)		3KV
Temperature Range		-20-100
Coil cable diameter		1.6/3.5/4.5/8mm
Power supply		DC Supply Adaptor 6V or Battery 4*AA
Size		160x80x28mm

TH6680-360-15 : 80V, 360A, 15kW Bidirectional DC Power Supply & Regenerative load Performance characteristicsPower supply: 342VAC-528VAC, 44-66HzBidirectional power supply and regenerative load are integratedUp to 92.5% energy feedback efficiencyOutput voltage 0-80VDCCurrent output: 360APower output: 15kWWide range of constant power output, can be extended up to 480kWWith CV, CC, CR, CP in power mode and CV, CC, CR, CP in load modeBuilt-in various function generators7 -inch 24-bit color TFT LCD capacitive touch screenHigh power density: 3U high, 19-inch chassis, the maximum power of a single machine is 15kWPower factor up to 0.99You can use the knob to adjust the voltage and current value roughly and finelyThe timing output time can be set (0.01-9999.99S)Screen information is stored in U diskChinese and English operation interfaceFlexible and convenient file operating systemThe instrument operating software can be automatically upgraded through USB HOSTAnalog interface for external analog controlRS232 , USB HOST, USB Device, LAN, GPIB can facilitate data communication with PC and remote control of the instrumentBuilt-in hardware OVP, OCP, OPP, OTP protectionSupport SCPI and MODBUS protocols
-Bidirectional power supplyTH6600 series bidirectional regenerative high-power DC power supply can be used as source output (forward current) and as load sink (reverse current), and has CV, CC, CR, CP operation no matter in power mode or load mode , suitable for product testing in the fields of electric vehicle motors, controllers, and electric vehicle powertrain systems.TH6600 series bidirectional regenerative high-power DC power supply can switch quickly and seamlessly when outputting and absorbing current, effectively avoiding voltage or current overshoot, suitable for testing energy storage equipment such as batteries, battery packaging and battery protection boards.- Regenerative energy absorptionTH6600 series bidirectional regenerative high-power DC power supply has the function of regenerative energy absorption, and the energy feedback efficiency is as high as 92.5%. electricity cost.D. Regenerative energy absorptionThe waveform can be set through the front panel, or uploaded through the host computer or USB.The instrument has built-in standard waveforms as follows, which can be recalled at any timeIn addition to the above standard waveforms, arbitrary signal generators can also be used to form more complex function signals, which can be divided into 99 groups of sequences for R&D and product testing. The generated function signals and sequences can be stored in a USB flash drive for easy recall.
Application:General testing for R&D and design verificationNew energy: solar cells, new power vehicles, electric bicyclesRoutine test and maintenance of production line workbenchAutomated device integration testingSolar photovoltaic simulation testTeaching laboratoryLED test

GW Instek currently offers more than 100 power supply products to meet a diverse range of applications including Electronic Assembly Testing, Education, Component Testing, Wireless Product Testing, Burn-In, Battery-Power Product Testing, Automotive, and Aerospace applications.