GST : 24ADRPP8869N1ZB
4.0/5
Our Products
Our Complete range of products are Cri Borewell Submersible Pumps, CRI Borewell Submersible Pump (80 MM), CRI Horizontal Openwell Submersible Pump, CRI Vertical Openwell Submersible Pump and Cri Openwell Submersible Pumps.
C.R.I. 80Mm (3") Submersible pumpsets are built with thermoplastic impellers, diffusers and inbuilt check valve. All vital components of these pumpsets are made of corrosion resistant thermoplastic and the shaft is of SS 304/410. Pumpsets are multistage centrifugal type. The optimal design of impellers and diffusers enables the best possible hydraulic efficiency.
The pumpset is firmly coupled to a submersible electric motor which operates submerged beneath the surface of water. Built-in chek valve prevents back flow and reduces the risk of water hammering. All mounting dimension of 100 mm (4") pumpsets and motors upto 2 HP are in accordance with Nema standard.
Applications :
Salient Features :
Pumped Liquids : Clean, thin, non-aggressive, non-explosive, clear, cold, fresh water without abrasives, solid particles or fibre having the following characteristics.
Technical Specifications
| Power range | 0.37 kW – 1.1 kW (0.5HP-1.5 HP) |
|---|---|
| Speed | 2900 RPM |
| Version | Single phase 200-240V,50 Hz, A.C. Supply |
| Maximum total head | 93 metre |
| Maximum flow rate | 5.4 m3/h |
| Maximum outer diameter in mm | 78 |
| Nominal outlet size in inches | 25,32 & 40 |
| Degree of Protection | IP 58 |
| Direction of Rotation | Clockwise from driving end |
| Thrust Load | 1500 lbs. |
| Minimum cooling flow along the motor | 0.15 m/sec |
| Type of duty | S1 (Continuous) |
| Method of starting | Capacitor Start and Capacitor Run (CSCR) |
| Maximum starts per hour | 20 times. |
| Mounting Standard | As per NEMA |
Specifications
| Material of Construction of Pump | |
|---|---|
| Part Name | Nominal Dia 80mm (3") |
| Check Valve housing | Cast Iron |
| Check Valve | Delrin |
| Check Valve seat | Nitrile butyl rubber |
| Outer shell | SS 304 |
| Impeller | Noryl |
| Diffuser chamber | Noryl |
| Stop ring | Hylem |
| Intermediate bearing (Sleeve / Bush) | SS 304 / NBR |
| Suction inter connector | cast iron |
| Pump shaft | SS 304 |
| Coupling | SS 410 |
| Material of Construction of Motor | |
| Shaft seal | Nitrile butyl rubber |
| Stator Shell | SS 304 |
| Thrust pad | Graphite Carbon |
| Thrust base | SS 420 |
| Diaphragm | Nitrile butyl rubber |
| Motor base | cost iron |
| Shaft | SS 431 |
Characteristics Of Clear Cold Water
| Maximum liquid temperature | 33 oC |
|---|---|
| Permissible amount of sand | 80 mm (3") – 25g/m3 (max), 100m (4"_ -25 g/m3 |
| Chloride ion density | 500 ppm (max.) |
| Allowable solids | 3000 ppm (max.) |
| Specific Gravity | 1.004 (max.) |
| Hardness (Drinking water) | 300 (max.) |
| Viscosity | 1.75 x 106 m2/sec (max.) |
| Turbidity | 50-ppm silica scale (max.) |
| PH value | 6.5 to 8.5 |
We are engaged in offering CRI Horizontal Openwell Submersible Pump. The CRI Horizontal Openwell Submersible Pump, we supply, has operating efficiency and long functional life. CRI Horizontal Openwell Submersible Pump, we offer, has power range of 0.37 kW – 1.5 kW (0.5HP-20 HP). The pump works well in open well where there is a wide fluctuation in water level.
Features :
Specifications
| Power Range | 0.37 kW – 1.5 kW (0.5HP-20 HP) |
|---|---|
| Speed | 2880 RPM |
| Version | Single phase 200-240V, Three phase, 380 -415V, 50Hz, A.C Supply |
| Maximum total head | Upto 80 m |
| Maximum flow rate | Upto 195 m3 / h (54 lps) |
| Degree of Protection | IP 58 |
| Direction of Rotation | Clockwise viewed from driving end |
| Nominal delivery size in mm | 25, 50, 65, 80 & 100 |
| Type of Duty | S1 (continuous) |
| Method of starting | Capacitor Start Capacitor Run (CSCR) / Permenant Split Capacitor (CSR) Direct on Line upto 5.5 kW, SD upto 30kW |
| Maximum starts per hour | 6 times |
Material Of Construction
| Part Name | Material |
|---|---|
| Rear cover / Bracket | Cast iron |
| Stator Shell | Cast iron / S.S / M.S |
| Impeller | Cast iron (FG 200 / S.S AISI - 304 / Lead Bronze |
| Shaft | SS AISI 410 |
| Pump casing | Cast iron (FG 200) |
| Shaft seal | Nitrile butyl rubber |
| Thrust assembly | Leaded Bronze and Compostos / Stainless Steel 420 with Graphite Carbon |
| Diaphragm | High Nitrile butyl rubber |
| Journal bearings | LTB 4 |
We are one of the ace Suppliers of CRI Vertical Openwell Submersible Pump. The rigid stainless steel stator shell helps CRI Vertical Openwell Submersible Pump to work efficiently under water. Detachable pump and motor in vertical higher stage pump comes with detachable pump and motor in vertical higher stage pump. We provide this pump at market leading price.
Features :
Specifications
| Power Range | 0.75kW – 1.5 kW ( 1HP – 2HP ) - Vertical |
| Speed | 2880 RPM |
| Version | Single phase 200-240V, Three phase, 380 -415V, 50Hz, A.C Supply |
| Maximum total head | 75 metres (7.5 bar ) |
| Maximum flow rate | 7200 LPH (7.2 M3 / Hr) |
| Nominal outlet size in inches | 1, 1¼,1½, 2 ,2½,3,4 & 5 |
| Degree of Protection | IP 58 |
| Direction of Rotation | Clockwise from driving end |
| Type of Duty | S1 (continuous) |
| Method of starting | Capacitor Start Capacitor Run (CSCR) / Permenant Split Capacitor (CSR) Direct on Line upto 5.5 kW, SD upto 30kW |
| Maximum starts per hour | 6 times |
Material Of Construction
| Part Name | Material |
|---|---|
| Pump Casing | CI |
| Stator Shell | SS 304 / Mild Steel |
| Impeller | SS, Cast Iron and LTB - 2 |
| Shaft | SS 410 |
| Journal Bearings | Leaded Bronze |
| Thrust Assembly | Leaded Bronze and Compostos / Stainless Steel 420 with Graphite Carbon |
Mr. Ramesh Patel (Ashish Auto)
Petlad Nadiad Road, Rangaipura, Petlad, Opp-GIDC, Anand, Gujarat - 388450, India
Share us via
