Autoclaves #6061130

• Triple safety against accidental over pressure.


• Safety Valve / Pressure control switch/ Digital Temp. indicator cum controller


• Design to work and withstand with 750 20 kpa.


• Simple in design and operation


• Easy heater replacement


• Calibrated Pressure Gauge


• Inside M.S. Boiler, air insulation cover, Glass wool Insulation cover and outer cover


• Special gasket is fitted in the grooves to resist high pressure and temperature.


• Teflon coated boiling chamber - resistive against corrosion


• Hard chrome plated autoclave lid - resistive against corrosion


• Safety against Electrical Short circuit


• Soak timer to regulate the autoclave timing independently, Need no manual shutdown


• Available in various Chamber Sizes

• Semi Automatic operation;


• Manual steam exhaust at the end of test cycle


• Single chamber for steam and water


• Working chamber fabricated from S.S. 304


• Exterior body is fabricated from MS Material


• Powder coated in attractive shades


• Lid, flange & bottom sheet also made of stainless steel.


• Joint less silicon gasket


• Heavy duty industrial flange heater (As per selected size)


• Microprocessor based Digital Temperature Indicator cum Controller


• PID Controller Controls temperature/pressure precisely at set value


• User adjustable in-built digital timer


• Pressure range : 15 to 22 PSI, factory set at 15 PSI


• Temperature Range : 121C to 125 C


• Temperature Accuracy : 0.5 C


• Temperature sensor : PT-100


• Lid fitting pressure gauge : 0-30 PSI


• Hydraulically tested at : 60 PSI


• Safety valves:02 Mechanical Valves, 01 Manual release valve


• Supplied with Calibration certificate with traceability


• Provided with DQ, IQ, OQ, PQ documentation


• Validation ports provided for temperature mapping as standard supply. (On customer request)

• Completely made of Stainless steel/Aluminum material.


• Fitted with pressure gauge and safely valve


• Safety valve is adjusted to blow off the seam at 12 PSI


• Maintaining constant pressure of 15 PSI


• ISI Marked


• Dimension : 30 x 30, 30 x 35, 30 x 55, 30 x 60


• Fitted with Digital controller to control pressure/temperature with temperature display indication.


• Factory set at 121 C (15 PSI) along with built in digital timer adjustable for maintaining sterilization cycle time with auto cut off system.


• Supplied with control panel, mains on/off switch, voltmeter, ammeter.

After it has set, cement must not undergo any appreciable expansion, which could disrupt a mortar or concrete. This property of soundness is tested by subjecting the set cement to boiling in water or to high-pressure steam. Unsoundness can arise from the presence in the cement of too much free magnesia or hard-burned free lime

This method covers determination of the autoclave expansion of Portland cement by means of a test of neat cement paste specimens, 25.4 X 25.4 X 285.8mm, which are moist cured for 24 hours +/- 1-1/2 hours and then exposed to action of steam under specified pressure for 3 hours. The rate at which pressure is increased in the beginning the test and released in the test are specified. Linear expansion is measured by micrometer comparator.

Silent Features:

• Rust proof stainless steel pressure vessel


• Specially designed Steam Safety Valve, pressure control switch and Temp. control switch - Triple Safety precautions for operator safety


• Accurately Calibrated Pressure Gauge


• Guaranteed timings and performance as per IS 4031

General Descripation & Specifications

The Autoclave is double walled. Inner boiler chamber of stainless steel cylinder, with concealed yet easily replaceable heaters surrounding the vessel for quick heating. The boiler lid is of thick stainless steel and can be bolted to the chamber by heavy hexagonal nuts. The silicon gasket, seated in a groove, makes the unit leak proof even at high pressure. The boiler is mounted in between the strong angle iron frame and covered with CRC sheet attractively powder coated. The outer cover can also be of Stainless steel at an extra cost. The gap in between the walls is filled with thermal insulation to prevent heat loss and energy. The control system consist of sensitive pressure regulator, pressure gauge, safety valve, temperature control switch, power ON-OFF switch and pilot lights to indicate status of the electric heating units and control switches.

Standard Accessories:

• Special rack to hold specimens above water level in the autoclave and in vertical position


• Pressure gauge with calibration report with national traceability


• Silicon rubber Gasket


• Spanner

Accessories At Extra Cost:

• Length comparator with dial micrometer 0.002mm X 5mm


• shrinkage bar moulds(single/two/triple gang)


• PID Auto tuning Digital Temp. indicator cum controller with or without PC interface for data logging


• PID Auto tuning Digital Pressure indicator cum controller with or without PC interface for data logging


• Spare heater set


• Spare Silicon Gasket


• Spare Pressure gauge


• Spare safety valve