Eureka Industrial Equipments Private Limited

Paud Road, Pune, Maharashtra

The EUSONIC flowmeters work on the Transit time ultrasonic principals. This put simply, involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. This is a more direct method of determining flow than some other systems and thus provides a more reliable measurement.

Ultrasonic transducers are mounted on the external surface of the pipe and are used to generate ultrasonic pulses which are passed through the pipe wall. The flowing liquid within causes time differences, frequency variations and phase shifts in the ultrasonic signals which are then evaluated by the flowmeter to produce an accurate flow measurement.

The key principle is that sound waves travelling with the flow will move faster than those travelling against it. The difference in the transit time of these signals is directly proportional to the flow velocity of the liquid and thus the volumetric flow rate. Whilst elements such as flow profle, liquid type and pipe material could have an effect on the measurement, the flowmeter electronics compensate for and adapt to changes in the medium in order to provide a reliable measurement.

The fast digital processors and sophisticated analysis used in the new EUSONIC flowmeter guarantee reliable, respectable results, even when used of a clamp-on flowmeter would not have been possible.

All measurements are independent of pressure and do not disturb the integrity of the pipeline in any way. This allows the flowmeter to be fitted to pipes where size, pressure, temperature, liquid type or pipe access would have made the installation of an invasive measurement device impossible.

No shut-down, no lost production

No pressure drop

No costly and risky mechanical installation

Low maintenance, no danger of blockage or damage

Quick and simple installation

Cost effective solution, particularity on large pipes.

KATRONIC make portable and field mounted Ultrasonic Flowmeters for liquids have easy to clamp on sensors with no process interruption, no pressure loss, fast and accurate, with diameters from 10 mm to 6.5 m. Can be used up to 4 independent flow channels.

Mass Flow Meters and Controllers for gas applications with an electronic housing suitable for laboratory conditions. EL-FLOW" series instruments are truly unique in their capability to control flow ranges between 0.1 mlnmin and 0.1250 lnmin with pressure rating ranging between vacuum and 400 bar - all in one range of instruments. This versatility in flow ranges and in operating conditions has ensured that the EL-FLOW series remains our most popular and field proven of instruments. These have a fast response and a high accuracy: 0, 5% of reading + 0, 1% of F.S., analog and digital [fieldbus] communication.

The Weld Neck Flange is normally referred to as "High Hub" flange. It is designed to transfer stresses to the pipe, thereby reducing high stress concentrations at the base of the flange. The pressure tappings are provided through the flange which are at a distance of 1" from the face of the plate.

MASS-VIEW Series Thermal Mass Flowmeters/Regulators operate on the principle of Direct Thermal Mass Flow Measurement. They have high Accuracy ( 1% FS 1% RD ), high Rangeability ( up to 1 : 100 ), OLED digital bar graph Flowrate & Total Flow display, low power consumption. These can be supplied in full scale ranges from 0.2 - 200 ln/min and handles pressures up to 10 bar(g). MASS-VIEW Flowmeters have various alarms and counter functions, analog output signals, a digital interface & two relay contacts. Flow control can be achieved by an optional built in high quality needle valve.

KATRONIC make portable and field mounted Ultrasonic Flowmeters for liquids have easy to clamp on sensors with no process interruption, no pressure loss, fast and accurate, with diameters from 10 mm to 6.5 m. Can be used up to 4 independent flow channels.

EUTURB consists of a multiple-bladed rotor mounted in a pipe, perpendicular to liquid flow. Liquid flows through the pipe causing a rotor to spin. As the rotor spins, an electrical signal is generated in the pickup coil. Pulses are counted & 4-20 mA gets generated with the use of converter.

Performance

Repeatability	:	0.2%
Accuracy Standard	:	1% of reading

Wetted Components

Body	:	Standard SS304 (optional SS316)
Bearings and Shaft	:	Tungsten Carbide
Rotor	:	Standard - 2Cr13 Stainless Steel (optional Alloy CD4Mcu)
Retaining Rings	:	SS316

Power supply, Protection

Power Supply	:	24 VDC / Battery operated
Flow, Totaliser display	:	optional
Transmitter	:	4 to 20 mA DC current signal
Housing	:	non ex. Proof / ex. proof
Protection	:	IP65

Manger + Wittman (subsidiary of Bronkhorst High - Tech) make Mass Stream Flowmeters & Controllers for gases have a unique, all AISI SS 316 sensors with low pressure drop and fast.

CORI-FLOW utilizes a patented, advanced Coriolis type mass flow sensor to achieve unsurpassed performance, even with changing operation conditions in pressure, temperature, density, conductivity and viscosity. CORI-FLOW is offered with or without an integral control valve but with both analog and digital communications. Flow ranges available between 0.200 g/hr and 0.600 kg/hr. These have a fast response time, high accuracy (up to 0, 1% FS plus 0, 2% of reading), IP65 housing with optional ATEX Zone 2 approval.

Mass Flow Meters and Controllers for liquids flow ranges between 0.30 mg/h and 0.20 kg/h (Water equivalent). LIQUI-FLOW has a fast and accurate measuring signal, analog (models L1/L2) and digital (models L10/L20/L30) versions available. These are insensitive to mounting position.