Ahmedabad, Gujarat, India
Our Products
TheI/P converter with various housing is available for cabinet installation, field installation, rail installation and as slide-in type. The signal conversion is based on standard signals. Current signals 0/4 to20 mA are converted to pressure signals 0.2 to 1 bar or 3 to 15 psi.
DESCRIPTION
General specifications:
TheI/P converter with various housing is available for cabinet installation, field installation, rail installation and as slide-in type. The signal conversion is based on standard signals. Current signals 0/4 to20 mA are converted to pressure signals 0.2 to 1 bar or 3 to 15 psi.
General specifications:
Greystone WallSurface Mount Carbon Monoxide Detector without LCD Dispaly, Range 0-300 PPM, Output 4-20mA , Power Supply 24VDCAC
Additional Information:
Delivery Time : Ex Stock
HONEYWELLIgnition TransformerET 401for Gas, Supply 230VAC, Secondary Voltage 14KV
The Series 72 Modutrol IV Motors are used to control dampers and valves. The motors accept a current or voltage signal from an electronic controller to position a damper or valve at any point between open and closed.
FEATURES
HONEYWELLZLDA01A2YSide Rotary Adj with 50mm Roller Elevator Limit Switch , SPDT snap action, 1/2NPTconduit
| features |
|
| typical applications |
|
honeywellmicro switchlarge premium basic switchesbz/ba/bm/be seriesare accurate, reliable and repeatable.these snap-action switches offer precision operation and sensitive differentialtravel. Theseseries are often used for precision on/off applications, as well as end of limit, presence/absence, and manual operator interface functions.
what makes our switches better?industry-leading temperature range for options up to 204 c[400 f] and temperatures as low as -55 c [-67 f]exclusive current carrying capability of up to 25 ainternational approvals: ul, csa, enec, ce listingsoptions for circuitry, styles, connection types and a wideselection of actuator stylesdependable performance -tested up to 20 million mechanical cyclesmicro switch legacy and expertise - over 75 years ofengineering excellence and experience
global use and approvalsswitches certified to ul, csa, enec, and ce for global use
flexibility of product characteristicshoneywells large basic switches offer various operating force and differential traveloptions to meet the actuator type. Designed with momentary or maintainedcontact action, these switches may perform a variety of functions as well asoffering a choice of actuation, termination and operating characteristics for designflexibility
varients for extreme conditionswith an ip64 sealing option to maintain switch enclosure sealing, many listings canbe used in dirty, harsh environments with their dustproof and splash resistantseals. Many versions operate in extreme temperatures, up to 121 c [250 f], and several with high temperature options for up to 204 c [400 f], as well astemperatures as low as -55 c [-67 f]
honeywellmicro switchdm-dp seriessnap-in panel mount basic switchesare snap-action switches in basic and manual configurations. They have quick-connect terminals and snap-in, panel mount housings for ease of installation. They include momentary and alternate actions, and single- or double-pole. The dm accept a button for manual operation. The dp have plungers for basic operation.
| features | ||
|
honeywellstandard basic switches v15 seriesis an electromechanical switch designed for enhanced reliability at a great value. The switch is often ideal with "low-cost-of-failure" - where the cost to replace the switch or to service any failure related to the switch is minimal. The v15 is designed for applications requiring greater than or equal to 100 g of operating force and electrical ratings ranging from 16 a to 22 a. The v15 series switch offers a wide range of standard offerings, including a choice of actuators, electrical ratings, operating forces, and circuitry and holds global approvals (enec, cqc, ul, and cul).
| standard v-basic switch features |
|
| potential applications |
|
Ex Intrinsically Safe Mobile Computeris the best choice for workers in the chemical, oil and gas, mining and pharmaceutical industries.It meets or exceeds stringent requirements for gases, vapors and liquids, dusts and fibers.
LKS 160air damper actuator is designed to be fitted to multi-stage or modulating oil and gas burners with fully closed position.
A synchronous motor powers a drive shaft and a backlashfreecam shaft via a gear reducer. The cam shaft operates limit and auxiliary switches. Theposition at which one of the limit or auxiliary switches operatescan be adjusted steplessly within the operating range usingthe associated cam disc. Manually adjustable lever-operatedcams or spindle-driven cams, which can be adjusted with ascrewdriver, are available.
The NDD Series nitrogen dioxide detector uses a superior electrochemical sensor for reliability and accuracy in the most critical applications. The NDD provides a 3-wire sourcing 4-20 mA output as well as an alarm relay with three jumper selectable trip level settings.
Measurement Range :0-10 PPM, Output Signal :4-20 mA, Adjustable Alarm Relay
FEATURES:
The CMD5B5 Series Duct Carbon Monoxide Detector uses an electrochemical sensor to monitor the carbon monoxide level and outputs a eld-selectable 4-20 mA or voltage signal. The voltage signal may also be set to 0-5 or 0-10 Vdc. The sensing range and output may be scaled to either 100, 150, 300, 400 or 500 ppm via the on-board menu. A front panel LCD is standard to ensure easy setup and operation.
Y-type strainer is widely used in water application and is used for protecting valve and other equipments from scrap and impurities in the system.
FEATURES
Multitrend SX recorder provides flexible electronic data acquisition and recording in a high functionality.
feature 5.6-inch TFT color LCD (640480) touchscreen displays with excellent visibility and intuitive control interface. It supports 27 types ofinput withhigh-speed sampling rate up to 25 ms and recording cycle between 1 to 3600sec. Various communication methods (USB, RS422/485, Ethernet) also supported.
AUTONICSSPB SeriesSwitching Mode Power Suppliesoffer high power conversion efficiency and stable power supply with low noise and ripple and minimal heat generation.The switching mode power supplies can be easily clipped onto DIN rails or mounted using screws.The slim and compact design also allows space-saving installation.
R7WiringElsters Inductive Output Pulser.ElsterPR7inductive pulse unit is fitted to theH4000, C4000andS2000series of inductiveoutput meters.
PR6WiringElsters Inductive Output Pulser.ElsterPR6inductive pulse unit isfitted to theV200/V210/V220and theH4000Pseries of meters.
AUTONICSE50S Seriesdiameter 50mm shaft type incremental rotary encoder are suitable for measuring angle, position, revolution, speed, acceleration and distance.
Serieshigh performance fiber optic amplifier, features a compact structure designed to fit into narrow spaces. This fiber optic amplifier has fast response speed of under 0.5ms, and can be compactly mounted. Also, external synchronization input function, mutual interference protection and self-diagnosis function enhance user experience.
Honeywell combination gas valve, for use with 24 vat heating appliances that burn natural or manufactured gas, or liquefied petroleum (lp) gas.
Additional Information:
Delivery Time : Ex Stock
the tzidc represents the digital, intelligent positioner for communication via hart within thepositioner family. Unmatched shock and vibration immunity of 10g up to 80 hz distinguishes the tzidc from others and guarantee reliable operation in almost all areas under harshest environmental conditions.
the tzidc represents the digital, intelligent positioner for communication via hart within thepositioner family. Unmatched shock and vibration immunity of 10g up to 80 hz distinguishes the tzidc from others and guarantee reliable operation in almost all areas under harshest environmental conditions.
general specifications:
Working Principle & Operation:
It is simple and reliable switch for level detection.It can be used for small or long range of storage tanks and reservoirs. Polypropylene rigid construction provides prevention from corrosion.Float tilt with liquid in rise & fall condition, accordingly micro switch operates from NO (Normally Open) to NC (Normally Close) position. It can be used as a multi point switch also.
Special Features:
Application:
Wall mounted line voltage room thermostat. For general purpose control of gas valves, zone valves, circulation pumps, ventilators, boilers etc. In heating or cooling systems. Approvals ce protection class ip30 switch functioncapacity spdt 230 vac, heating terminal 10 a resistive, 3 a inductive; cooling terminal 6 a resistive, 2 a inductive terminal max. Wire size 4 mm2 erp class I temp. Setpoint range 10 . 30 oc differential fixed 1 oc temperature element vapour filled temp. Element place built in heating cooling application h or c earthing double insulated housing (hxwxd) 83 mm 83 mm 40 mm additional description lamp is generally supplied potential free, and can be wired to indicate heating or cooling operation, or boiler lockout.
Additional Information:
Delivery Time : Ex Stock
To filter fuel gas and combustion air supply to all gas consuming appliances. Applicable types of fuel: manufactured gases (town gas) natural gases (group H - methane) liquefied petroleum gas (lpg) non-aggressive gases air The filter complies with the reguirements of DIN 3386.
SPECIFICATION
Product rangeModel HUF (pipe sizes 1/2 up to DN150)
DimensionsSee dimensional drawings and table on page 2
Pipe size1/2 up to 2 inlet and outlet internal pipe thread according toISO 7-1DN25 up to DN150 inlet and outlet flange connectionsaccording to ISO 7005 EN1092-4
Maximum inlet pressureThreaded version: 6 barFlanged version: 6 bar
Ambient temperature range-15.80 C
ConnectionsThreaded version: Rp 1/4 connections for inlet or outletpressure tapsFlaged version: Rp 1/4 connections for inlet or outletpressure taps
CapacitiySee capacity curves on page 5.
Torsion and bending stressPipe connections meet group 2, according to EN161requirements.
Seals and gasketsHydrocarbon resistant NBR rubber type, EN549
Body materialAluminium ally die cast, EN AB 46100, EN AB 43100
FilterSelf-Extinguishing synthetic fiber for gases conforming toDVGW-G260/1.Galvanized electro welded mesh.
Standards and ApprovalsThe HUF Series gas filter conform with the followingECdirectives:Gas Appliance Directive (90/396/EWG)PIN: CE045
The BC1000A/B series is a flame switch for intermittent operation to indicate presence or absence of a flame and to be applied in commercial or industrial burner installations. The BC1000A can also be used as a primary control for manually operated burner systems using a start/stop station. In addition to the flame sensing functions, the BC1000A/B provides a Safe Start function which checks if a flame signal is present when applying power to the device. If so, the BC1000A/B holds its operation until the flame signal disappears. The BC1000A/B can be used with a recifying flame rod or all existing non-selfcheck Honeywell PowerTube type UV sensors (for intermittent operation only.
DESCRIPTION
The BC1000 (FR models) will operate also withthe ex-Satronic IRD810/1010 range of infraredsensors. Note that this combination is NOT CEapproved for use on installations that fall underthe GAD (Gas Appliances Directive).
FEATURES
1) Compact design.2) Plug-in wiring sub base for direct panel orDIN RAIL mounting.3) Safe-start check (SSC) feature preventsoperation when abnormal flame conditionexists at start-up.4) LED indication (Power, Flame, SSC) on thefront to show operation status (SSC hiddenbehind the front cover).5) Screw terminals on the front providecontinuous 06VDC flame signal strengthmonitoring
Reversible gear motors to transmit rotary movements between 0 and 90 or 0 and 160, for actuation of gas and air valves, with voltage-free limit switches, automatic/manual mode changeover (optional), position feedback and externally readable position indicator. Running times: 3.7 to 214 s, mains voltage: 24 V AC, 110/120 V AC or 220/240 V AC, torque: 1.2 to 20 Nm, controlled by three-point step signal, continuous signal or two-point signal.
More Information:
Microprocessor, electronic components, output relais and flame amplifier are placed on two printed circuit boards. These plus the lockout- and reset circuit are well protected inside a flame resistant, plug-in type plastic housing. The reset switch for reset / remote lockout with its built-in LED for displaying the information system plus the central fixing screw are placed on top of the housing. The wiring base S98 is equipped with spare- and extraterminals and allows together with a variety of cable entry points utmost flexibility of electrical wiring.
The burner control box DLG 974/976 controls and supervises
power burner for gas and dual fuel. The control box is
approved and certified according the relevant European
standards. The use on direct air heaters according DIN 4794
is also possible.
The microprocessor- based programming sequence ensures
extremely stable timings independent of voltage variations,
ambient temperature and/or switch-on cycles. The
built-in information system not only provides a continuous
monitoring of the actual state of the box (very helpful especially
for monitoring the start-up phase) but also informs
about the cause of a possible lock out. The lock out cause
is stored in such a way that it can be retrieved even after a
power failure.
The control box is designed for maximum safety in case of
fluctuations in the voltage supply. If the mains voltage drops
below the permitted level, operation is interrupted and the
control box automatically prevents the start sequence from
being repeated. In this way, the safety of the system is not
put at risk by a drop in the mains voltage. This low-voltage
protection works not only during start-up but also permanently
during operation.
The Honeywell DBC2000 is a microprocessor-based integrated burner control for automatically fired gas, oil or combination fuel industrial single burner power burner applications. The DBC2000 system consists of the relay module and wiring subbase. The DBC2000 Standard Model provides the minimum requirements to control an industrial burner system, such as automatic burner sequencing, flame supervision, system status indication, system or selfdiagnostics and troubleshooting. The DBC2000 Enhanced Model includes an integrated Valve Proofing System, as well as well as bus communication.
The DBC2000 is programmed to provide a level ofsafety, functional capability and features beyond thecapacity of conventional controls.
FEATURES
Employs a plug-in mounting methodUses a microprocessor to improve performanceThe progress of the sequence can be easilydetermined by status indicator LEDsAll models have a 4-wire firing rate switchingcircuit to control an air damper or other auxiliaryequipment during startup of the burner.Safe start check before and during pre-purgeSafety shutdown occurs on- malfunction of the burner controller- failure to ignite the pilot burner or main burner- loss of flame during run period- opening of air flow switch during pre-purge, start-up, run and post-purge period- flame signal detection during standby or prepurgeperiodRemote communication (Enhanced model only)Valve Proofing System (Enhanced model only)
Mains input: Supply voltage220 to 240Vac -15% +10% 50/60Hz or110 to 120Vac -15% +10% 50/60Hz
Allowable ambient Temperature & Humidity-10 C; +60C90% RH max. at 40C (non condensing)
ApprovalsCE certification to standard EN298:2003CE certification to standard EN230:2005
Additional approvals:Lloyds (planned)EN746-2 compliantPED (planned)SIL2 (planned)Apave (planned)
Honeywell BC1000A0220F FLAME SWITCH, 2 1 Sec. flame response time, C7012A/C7012G flame sensor connected, 220230Vac, 50/60Hz, 5W Power Consumption.
The Honeywell DBC2000 is a microprocessor-based integrated burner control for automatically fired gas, oil or combination fuel industrial single burner power burner applications. The DBC2000 system consists of the relay module and wiring subbase. The DBC2000 Standard Model provides the minimum requirements to control an industrial burner system, such as automatic burner sequencing, flame supervision, system status indication, system or selfdiagnostics and troubleshooting. The DBC2000 Enhanced Model includes an integrated Valve Proofing System, as well as well as bus communication.
FEATURES
Employs a plug-in mounting methodUses a microprocessor to improve performanceThe progress of the sequence can be easilydetermined by status indicator LEDsAll models have a 4-wire firing rate switchingcircuit to control an air damper or other auxiliaryequipment during startup of the burner.Safe start check before and during pre-purgeSafety shutdown occurs on- malfunction of the burner controller- failure to ignite the pilot burner or main burner- loss of flame during run period- opening of air flow switch during pre-purge, start-up, run and post-purge period- flame signal detection during standby or prepurgeperiodRemote communication (Enhanced model only)Valve Proofing System (Enhanced model only)
The VR8204 AND VR4204 Intermittent Pilot Dual Automatic Valve Combination Gas Controls are used in gas-fired, intermittent pilot appliances.The controls include a safety shutoff, a manual valve, two automatic operators, a pressure regulator, a pilot adjustment screw and a conduit cover (VR4204 only).
VR8204 used with S8600, S8610 and S8620 Control
Modules.
VR4204 used with 120 Vac intermittent ignition modules.VR8204 for use with 24 Vac heating appliances and
VR4204 for use with 120 Vac heating appliances that
burn natural or manufactured gas, or liquified petroleum
(LP) gas.
Capacity rated at 150 cfh at 1 in. wc pressure drop[4.2 m3/hr at 0.25 kPa].
Solenoid-operated first automatic valve opens on thermostatcall for heat and closes when call for heat ends.
Diaphragm-operated second automatic valve opens undercontrol of the regulator and closes if gas or powersupply is interrupted.
Two-position gas control knob has ON and OFF positions.
All adjustments and wiring connections are accessiblefrom top of the control.
Compact size.
Straight-through body pattern; right angle adapters availablefor inlet and outlet.
1/2 in. inlet and1/2 in. outlet; adapters available for 3/8or 3/4 in.
The gas governors are conformity with EN 88 standard (2009/142/CE gas regulation). The governors are suitable to systems' installation with automatic gas burners including mixed and combined systems and to in industrial distribution systems.
TECHNICAL FEATURES
Compensation diaphragm, operating diaphragm andsafety diaphragm: an external breather outlet pipe is notnecessary as the incorporated safety diaphragm ensuresthat, in the event of breakage of the operating diaphragm, no gas leakage (over 30 dm3/h) is possible inside theroom (in compliance with par. 3.3.2. EN88specifications).
INSTALLATION
Install the governor with the diaphragm positionedhorizontally (on horizontal pipes). Be careful to followalways the direction of gas flow indicated by the arrow onthe governor.Suitable tools must be used for the governor fitting on theinlet and outlet hubs. Never effect leverage on the sleeveof the upper cover when fitting the governor.For all models with the filter inside, the governor is bestfitted at a comfortable height from the ground so as tofacilitate the filter cleaning (fit always a suitable gas filterupstream the governor).Make sure that the pipes are clean and aligned so thegovernor is not under stress.Do not remove the perforated diaphragm breather cap (3)and do not obstruct the hole, otherwise the governor willnot work. Install the governor so avoiding contact withplastered walls.Make sure that the governor is suitable to the intended use.
The burner control units BCU 480 control, ignite and monitor gas burners for intermittent or continuous operation. As a result of their fully electronic design, they react quickly to various process requirements and are therefore suitable for frequent cycling operation. They can be used for industrial burners of unlimited capacity which are ignited by pilot burners. Pilot and main burners may be modulating or stage-controlled. The BCU 480 monitors pilot and main burners independently. The pilot burner can burn permanently or be switched off. The BCU is installed near the burner to be monitored. On industrial furnaces, the BCU reduces the load on the central furnace control by taking over tasks that only relate to the burner, for example it ensures that the burner always ignites in a safe condition when it is restarted. The air valve control assists the furnace control for cooling, purging and capacity control tasks.The program status, the unit parameters and the level of the flame signal can be read directly from the unit. The burner can be controlled manually for commissioning and diagnostic purposes. If the local requirements on the burner control unit change, the PC software BCSoft can be adjusted to the unit parameters of the application by using the optical interface. The service personnel is supported by a convenient visualization system of the input and output signals and the error history.
The new power management scheme reduces installation and wiring costs. The power for the valves and ignition transformer is supplied via the power supply of the BCU, protected by a replaceable fine-wire fuse. The conventional wide-spread systems used in industrial furnace and kiln construction require bridging of large distances for signal processing. The optionally available BCU.B1 for connection to the PROFIBUS DP fieldbus is equipped for this purpose. As a standardized fieldbus system, the PROFIBUS DP considerably reduces development, installation and commissioning costs compared to conventional wiring.
The use of a standard bus system offers massive benefits compared to manufacturer specific bespoke solutions. Time-tested hardware components, standardized connection methods and a series of tools of bus diagnostics and optimization are available on the market from a whole range of manufacturers.
The widespread use of the system ensures that the planning and service personnel are very familiar with how the system operates and how to handle it and can therefore operate the system efficiently.
The BIO burner is designed for industrial furnaces and firing systems in the iron and steel industries in the precious, non-ferrous, and light metal sector, as well as in the plastics, fiber, and paper industries. Other fields of application are thermal incineration installations, as well as dryers and hot-air generators. For low temperature applications (e.g. for crucible heating, radiant tube heating, or hot-air generation), the burners are equipped with a heat-resistant steel attachment tube. For high temperature applications (e.g. forging furnace), the burners are used in combination with a burner quarl made from refractory concrete. Different flame shapes can be achieved by using burner quarls with a different geometry. The burner can be adapted to the system requirements using different burner tube lengths.
AIR-300: The AIR-300 is a microprocessor based air quality monitor/controller sensitive to a wide variety of air pollutants.
FEATURES
APPLICATIONS
DESCRIPTION
The AIR-300 is a microprocessor based air quality monitor/controller utilizing a hot wire element sensor based upon the Taguchi principle. This is a full spectrum sensor sensitive to a wide variety of air pollutants such as carbon monoxide, smoke, benzene, alcohols, hydrogen, hydrocarbons, esters, etc.
This sensor is better suited to measuring air quality than a sensor which measures only Carbon Dioxide. The AIR-300 yields a true indication of the actual air quality, rather than occupancy. For example, if a person were to smoke a in a room, the carbon dioxide sensor would be inadequate in detecting this, even though the air quality had significantly degraded. This same set of circumstances holds true for many other contaminants such as Solvents, Fuels, and even Carbon Monoxide, all of which are much more harmful than Carbon Dioxide.
When measuring Air Quality, it is not so much the type of contaminant that is of concern, but rather the presence of any contaminants. This sensor does not indicate which contaminant is in the air, but indicates the presence and quantity of any contamination.
The Greystone AIR-300 monitor/controller works by looking at the signal from a full spectrum sensor, automatically compensating for temperature and humidity effects, and judging the degree of pollution. For the unit to perform efficiently it must work as a monitor/controller, i.e. it must be able to act upon level changes. The output is represented as an analog, stepped or relay output with user adjustable settings. This output can be used to directly control an actuator, or be sent back to a Building Automation System (BAS).
The AIR-300 can be configured to run in auto or manual mode and has an integral sensitivity adjustment to provide the user with the optimum settings to monitor a specified area. There are internal LED indicators to show microprocessor status and also a manual override feature to assist in installing the unit.
Thyristor Power Controller Multidrive 2PH up to 2700A 3 wire / 24Vac to 690Vac Supply / 4-20mA or 0-10V DC linear inputs, 10K Pot or RS485 Comms input / Burst Firing, Delayed Triggering + Burst Firing.
Ideal for:normal resistive & transformer coupled with normal resistive load types
Multidrive is a fully digital and universal Thyristor Power Controller designed to drive 2 legs of 3 phase resistive & transformer load types. Available in 19 Amp sizes from 45A to 2700A the Multidrive provides the user with optimum control of the process and ease of set-up & maintenance. The Front panel keypad & display allows total flexibility for the user with full configuration of the process & digital inputs types and firing & control modes, to suit the application. Real time values such as the Voltage, Current & Power can be read from the display. Internal quick-blow fuses as standard provide complete protection for the thyristor. Additional features such as current limit, profiling, heater break alarm and RS485 comms come as standard.
Overview:
Thyristor - CD3000M 2PH 15A to 700A DC Logic/Linear, ZC/BF 24V to 600VAC Supply, DC Logic, 4-20mA, 0-10V DC linear or 10K potentiometer inputs. CD3000M-2PH is a digital and universal Thyristor unit fully configurable via serial communication port.
A fully digital and universal Thyristor, configurable via RS485 serial communication port or dedicated configuration port for all inputs, firing & performance parameters.Configuration software available as a download at no cost.
Overview:
