HORIZON ENTERPRISES

Rajouri Garden, Delhi

A handy pocket caliper, made from solid brass. Close tolerance dovetail design ensures smooth motion of the caliper and provides accurate measurements.Graduated in both imperial and metric graduations with a least count of 1/16" on the imperial scale and 0.1 mm on the metric scale, these are ideal for use by mechanics, hobby crafters etc. who need to take measurements on small objects such as nails, screws, lenses, tubing etc.

These are available in two types:1. Brass Calipers (Outside)2. Brass Calipers (Inside and Outside)
1) Brass Calipers (Outside) Used for making external measurements from zero to the measuring range of the caliper2) Brass Calipers (Inside and Outside) Used for making both internal and external measurements. External measurements can be made from 0 - 4" (0 - 100 mm), whereas internal measurements can be made from 7/32" (5 mm) to 4" (100 mm)

A versatile tool, the Depth Gauge with Protractor allows for measurement of both angles and depths.

1. Manufactured from stainless steel, the protractor head has permanent deep etched graduations, 0-180 in opposite directions, thus permitting reading an angle directly and also its supplement
2. Depths are measured by a 6" (150 mm) steel rule. It is graduated in imperial dimensions on one side and metric on the other and can be set at any desired angle for use as a protractor and lengthwise when used as a depth gauge. A knurled thumbnut locks the rule in the desired position
3. The gauge has a flat surface on the back of the head permitting laying the tool flat upon the work. The rectangular head provides additional convenience as it incorporates 4 working edges
4. Angular Tolerance: 0.5
5. Head : Round & Rectangular

perfect for marking on parts of different thickness. This special device provides easily adjustable impact force.also suitable for sheet metal work. (riveting, flaring, piercing, shearing, bending etc.) hand models and pneumatic models available.

ip-1100maximum adjustable striking load capacity of1.1 ton

ip-3500maximum adjustable striking load capacity of3.5 ton

Salient features of high precision stamp marks are as follows:

1. Produced from large scale calligraphy drawings to capture every tiny detail of any logo.2. High wear-resistance and lasting precision to ensure the longest life of stamp mark.3. Scientific heat treatment imparted for prolonged service life.4. Lowest machine downtime because of the stamp mark`s longest life.

Made of Hardened and Ground high Carbon Steel.
Hardness 55 to 62 HRC.
Consists of two 'anti-friction' Bearings.
Single Row Deep groove ball bearing and Taper Roller bearing to absorb combined radial and thrust loads.

Manufactured from stainless steel, the Degree Protector comes with a semi-circular or a rectangular head.

1. The head has permanent deep etched graduations, 0 to 180 in opposite directions thus permitted reading an angle directly and also its supplement
2. The 6" (150 mm) blade has a graduation line on one end that permits accurate setting and reading of angles. The blade can be firmly set at the desired angle by means of a knurled nut
3. This is an ideal tool for machinists, draftmen and mechanics for setting bevels, transferring angles, small squaring tasks, checking cutter clearances within limits etc.
4. The rectangular head provides additional convenience as it incorporates 4 working edges
5.Angular Tolerance: 0.5
6. Head : Round & Rectangular

automatic rotary numerator with 6 wheels, with a special design to ensure that figures advance one-at-a-time accurately and automatically .

consecutive serial numbers can be marked on metal parts in simple operationspecial design ensure that figures advance one at- a--time accuretely and automatically.impression are perfectly aligned, evenly spaced, uniformally deep-part after part!

wheel made from special toolsadvancing cams machined into solid wheelsextra wide unit wheel for longer lifeopen piece actuating pawl machined from soliddirect reading character to check set upholding catch and spiring of unique design

Manufactured from Flat Steel.

1. Rivited head to give rigid position without play.
2. Just twist the nut and each reamer expands to the smallest size of the next larger size
3. Tension can easily be adjusted as desired.

QUALITY

Lokriya.
Ranglepak.
Harris Single.
Harris Double.

Description:

Size: 13 mm to 200 mm.

Rotary type numerator is specially designed to mark serial numbers, part numbers or code numbers on steel, alumunium; brass etc.This rotary type numerator is ideally suited for steel producers. Some key features of this rotary type numerator are as follows:

1. Perfect -time saver for repeat number by hand stamping2. Serial numbers, part numbers or code numbers can be marked compact in size3. marking wheels` can be rotated to any designed positions, then locked positively by a locking pin4. Individual release5. No loose parts6. Wheels made from special tool steel7. All part treated to remove scale and plated to resist rust

made from high quality tested carbon steel.
special material and double induction hardening give very high quality of stamping.
head is tempered to prevent chipping while hammering.

contact us

The ability to measure depths and angles is combined in this versatile tool.

1. The head is made from selected steel and has an attractive black finish. It is graduated both left and right to 15, 30, 45 and the rule can be set to any of these angles
2. A 6" (150 mm) steel rule is fitted to the head and can be locked in final position for depth or angular measurements by a knurled nut

made from stainless steel, these rules have a polished finish with permanently engraved clear to read graduations.

these are available in two types:
1. imperial & metric combined rules2. metric rules

these rules are graduated in metric dimensions on one edge and imperial on the other.imperial dimensions are in 1/16th, 1/32nd & 1/64 ths. metric dimensions are in 0.5mm & mm. reverse side of the rule has a permanently engraved metric to imperial conversion table3. all reamers marked with sizes

graduated in metric dimensions 0.5mm & mm on both edges

drop forged from specially drawn medium carbon steel, these drift keys are accurately hardened for increased resistance to wear.

used for conveniently removing taper shank drills and remers from sleeves and sockets, these are blackened and have a premium shot blast finish with permanent marking of size for easy identification.

A basis tool for machinists and toolmakers, the Universal Surface Gauge is used for accurately scribing lines, transferring measurements or probing surfaces in inspection work.

Design incorporates:
1. A fully hardened and ground base which serves as an accurate reference surface.
2. A machined Vee groove in the base allows the gauge to be used conveniently on curved surfaces.
3. A Vee groove at the front end allows the spindle to adjust to any angle above or below the base allowing it to be used as a height gauge and also as a depth gauge.
4. Two retractable pins allow the gauge to be located against the edge of a surface plate or T-slot for linear work.
5. Grooves on the side of the base allow for comfortable grip.
6. Well tapered scriber for better sighting while working. The scriber tip is hardened to 55-60 HRC.

Scrapers are used for smoothing, cleaning, and deburring plastics and metals. With their hardwood handles they prepare the surface for soldering, removing excess solder and opening bezels. Can be resharpened on a bench stone.

Total length 7" with a 2-1/2" blade length

Double Ended one piece boring bar have 90 & 45 square ends.
They are supplied with Allen key and Screw but without tool bits.
Shiny Black Finish

manufactured from selected steel, accurately hardened, this is an excellent tool for boring through holes or to a shoulder.

the angle permits maximum sweep diameter with minimum tool projection and can machine upto 6" wide surface with a standard tool bit.
complete set consists of 3 fly cutters with shank fully counter balanced to ensure a smooth finish.

Manufactured from high grade steel, these toolholders are accurately machined and ground.

Toolbits are held parallel and straight to the shank giving maximum support to the cutting edge. Set screws are made from heat treated alloy steel with hardened points for increased resistance to wear.
These are available with straight shank, right handed or left handed offset shank.
Each holder comes complete with an allen key but without toolbit.

The rigid and robust construction of the range of knurling tool holders makes them ideal for countless knurling applications.

These are available in 3 types:
1. Knurling Tool Holders - 3 Pairs
2. Knurling Tool Holder - 1 Pair
3. Knurling Tool Holder - 1 Knurl

a-grade : made from carbon steel hardened and ground- internally and externally.
workshop grade : made from carbon steel .
reamed internally.
externally ground and hardened

it finds application on drill presses, milling machines, planers etc. Any place where leveling is necessary

lifting capacity is approximately 1000 lbs (454 kgs)

designed for versatility and accuracy, these vee blocks are ideal for holding round or irregular shapes for scribing, grinding, measuring, machining and testing applications.

1. These can be used either ways, up or standing on end, all vee's and faces can be energised or de energised simultaneously by turning the rotary action control knob. This feature enables the vee block to hold both itself and the work on any flat ferrous surface including a permanent magnetic chuck (without energising the chuck).
2. Brass knob ensures no interference with the magnetic field, unlike the conventionally used steel knobs.
3. Also available with hardened vee's: 55-60 hrc for increased wear resistance
4. For applications requiring two vee blocks matched and numbered pairs are available

contact us

This quality reamer set creates precisely sized holes up to 1.5"! With just a simple twist, each reamer can expand to the smallest size of the next larger size in the set. Each reamer is constructed out of harden steel and is marked with its size for easy identification making this a great set of tools for any metal worker needing precisely measured holes in their sheet metal.

This range of tap wrenches are ideal for holding taps, reamers, screw extractors and other such small hand turned tools. All wrenches have a sliding T handle frictionally held, that allows these tap wrenches to be used even in confined spaces.

These are available in two types:

1. Regular T Handle TypeSelf-centering hardened steel jaws provide a positive grip on taps, reamers and other such small tools.

2. Ratchet TypeThese tap wrenches have self centering hardened steel jaws and knurled chuck sleeve, which provide positive grip on taps, reamers and other such small tools. The ratchet can be set left or right, or direct engagement in neutral position. This feature allows them to be used in confined areas with ease.

The Pin Chuck is a very useful reducing chuck used for holding drills too small to be held by a regular chuck. It is gripped in the larger chuck already on the machine by means of the back shank. Supplied with three interchangeable collets for holding small drills in varying sizes

we offer qualitative array of drill chuck arbor for drill chucks, that is fabricated using superior grades of raw material. These drill chucks are highly appreciated by our esteemed clients for its apprehensive features and high tensile strength. Moreover, our range of drill arbors are widely used to mount a drill chuck or any other tool onto the machine such as drilling machine. Available in various specifications, these drill chuck arbor can also be custom made as per the client specifications.

the jacobs taper (abbreviated jt) is commonly used to secure drill press chucks to an arbor.

adapter collect pin chuck set, holds drills upto 2.2mm, shank 3/32"

weight: 15 gms/pc

A range of angle plates is made both in plain and slotted types, with slotted types further available in open end and webbed end types. Manufactured from close grain cast iron. All the working faces are ground to 90 degree and true to each other. Jobs can be clamped to angle plate with the help of clamps. Angle plates can also be bolted to machine table.

Plain Angle PlatesThickness (in mm) 20, 22, 25, 28, 31, 33, 36

Slotted Angle Plates
Note:- Available inopen endas well aswebbed end

Sizes Available :-

Manufactured from high tensile, malleable cast iron, with an attractive grey hammertone finish, these are very useful for holding workpieces securely for smooth and even turning.

Used in conjunction with a catch-plate, these act as a driving device while turning material between centres.
A 'V' groove in the body helps clamping of round jobs.

CONTACT US

This range of die holders is best suited for applications requiring efficient and clean cutting of external threads. Die holders have a rugged construction with heavy duty set screws that hold the die firmly in place.

These are manufactured in two types:
Bodies with chrome plated handles.
All steel construction with black powder coated body. Handles have knurled ends, the ends being black powder coated.