Pune, Maharashtra, India
Our Product / Services
Indigo Stain Block Primer is a water based primer suitable for use on interior / exterior walls and ceilings. It is specially formulated to prevent the migration of stains through the finished paint film. It can easily hide the stains caused by water and solvent based inks, crayons, ball-point pens, coffee, grease, spices and cooking oils, water, and smoke damage.
Surface Preparation & Application:
To get the best results, ensure surfaces to be painted are sound, clean and dry (new surfaces particularly must be fully dry) and free from all defective or poorly adhering material such as efflorescence, dirt, grease or wax. Where necessary, surfaces should be rubbed down using a suitable abrasive paper and then dusted off. To use, stir thoroughly and apply 1 coat of Stain Block Primer to the stained surfaces without diluting with water and allow to dry for 8 hrs. Two coats are recommended for difficult stains.
Indigo Machine Colourants are specifically formulated Universal colourants, suitable for tinting both water based & solvent based decorative paints. Uniformly mixed the contents of the colourant by shaking it well before transferring it to the canister of the colourant dispenser. For fresh filling of canister ensure that the surface is clean & dry. Dont rinse the colourant container with water or any other solvent.
Indigo Dirtproof & Waterproof Exterior Laminate is specially formulated with groundbreaking nanotechnology to give an extremely smooth and dirt resistant finish, which will keep the walls looking new for a very long time. It is based on flexible acrylic emulsion fortified with Silicone polymer, thus giving high UV resistance with increased water repellancy. The paint film bridges micro cracks, and therefore prevents water ingress, providing waterproofing action. It is highly UV resistant, with very powerful anti-algal and anti-fungal properties. It is the only exterior emulsion to offer both dirtproof and waterproofing properties together.
Surface Preparation & Application:
Clean the surface of loose paint, dust and grease. Scrub vigorously with wire brush to remove algae, fungus and moss growth, especially on horizontal surfaces prone to water stagnation. Seal cracks with a 1:3 mixture of cement and sand. Use of Indigo Polymer Putty is highly recommended. For newly plastered surfaces allow 3 months prior curing. Apply one coat of Indigo Exterior Wall Primer, obtained by thinning 1 litre of primer with 1 litre of water. Follow with 2 coats of Indigo Dirtproof & Waterproof Exterior Laminate, obtained by thinning 1 litre of paint with 400 ml of water. 3 Coats are recommended for horizontal surfaces like ledges, sun-shades, etc. Apply with brush, roller or spray keeping 4-6 hours interval between coats.
Indigo Paints Knifing Paste Filler is an alkyd based putty ideal for levelling metal &wooden surfaces.
Surface Preparation & Application:
The Surface to be puttied should be cleaned free of rust, dirt, loose material, grease, wax etc. An appropriate Indigo Wood / Metal primer should first be applied.For Metal Surface , Indigo Knifing Paste Filler Grey should be applied using a putty knife on primed surfaces to even out the dents on the sheet metal and blowholes on casting before the finish paint is applied.For Wooden Surface, Indigo Knifing Paste Filler White should be applied using a putty knife on a primed surface to even out and fill up the grain in wood before the finish paint is applied. If the filling required is thick, for both wood & metal, this should be done in two or more thin layers and not in one thick layer. the puttied surface should be smoothened with abrasive paper grit no.320 before application of finish coat. If thinning of Knifing Paste Filler is required, use only general purpose thinner.
Indigo Paints brings you a special paint to beautify your exterior floor tiles, and to protect your flooring from algal or fungal attack. It is suitable for application on terrace floor tiles, cement tiles affixed to driveways and walkways, or on any plain cement surface. The paint not only provides an aesthetic glossy finish, but is also resistant to abrasion from human and vehicular traffic, sun, rain, and fungal attack.
Surface Preparation & Application:
To apply, first wash the surface with a hose to remove loose dust. Scrub vigorously with wire brush to remove algae, fungus and moss growth, especially on surfaces prone to water stagnation. Apply a self-priming coat of Indigo Floor Coat Emulsion, by diluting the emulsion with 30-40% water. Follow with 2 coats of Indigo Floor Coat Emulsion, thinning with water to obtain brushable consistency, keeping 6-7 hour interval between coats. Do NOT allow traffic on the surface for 48 hours, to allow the paint to develop full hardness.
Surface Preparation & Application:
Suitable for both interior and exterior use. For priming plastered walls, asbestos, concrete, brickwork, etc. Has excellent sealing properties and good resistance to dampness, efflorescence and alkali. Provides excellent bonding with surface and with topcoat emulsion. Gives very high hiding properties and whiteness. Apply on dry, clean and sound surface. Use one or two coats depending on surface condition. Dry 24 hours before applying finishing paint. Use clean fresh water for thinning.
Surface Preparation & Application:
Sand the surface with Emery Paper 180. Wipe clean with soft cloth. Apply a coat of Indigo Water Thinnable Cement Primer. Allow 6-8 hours for drying. Smoothen the surface by filling cracks with thin coats of Indigo Acrylic Wall Putty and allow 4-6 hours to dry. Sand with Emery Paper 180 and wipe clean. Apply another coat of primer. Sand the surface with Emery Paper 320.
Indigo Paints Zinc Chromate Primer is an alkyd based metal primer intended for maintenance applications. It consists of rust inhibitive pigments which protect the metal surface from rust.
Surface Preparation & Application:
Stir contents thoroughly. Clean the surface to be painted by removing all loose particles, grease, dirt, rust etc. Apply Indigo Zinc Chromate Primer using brush or spray after thinning 15-20% with turpentine. Allow the film to dry overnight before applying the topcoat.
Indigo Satin Enamel is an alkyd based enamel that can be applied on diverse surfaces like wood, metal and concrete. It comes with a soft sheen finish. Indigo Satin Enamel offers clean colors and is available in a range of shades. It can also be applied on exterior surfaces.
Surface Preparation & Application:
Wipe the surface clean to make it free from dust, dirt, grease etc. Sand the surface with abrasive paper grit no. 180. Wipe clean and use an appropriate primer to prime the surface. For best results, allow drying time of 6-8 hours. Dents & imperfections can be filled using appropriate fillers which should then be sanded and primed again. One liter of Indigo Satin Enamel can be thinned down with 10-20% of good quality turpentine for brushing consistency or with 20-30% for spraying. Apply two coats giving an interval of 6-8 hours between coats.
Sleek-XT Polyurethane (PU) System comprising of sealer and topcoat offer complete protection and retain natural beauty of exterior joinery like doors, windows and other woodwork. It forms a non-yellowing film that also resists the adverse effects caused on the wooden surface by ultraviolet rays, rain and humidity.
Surface Preparation & Application:
Sand the wooden substrate along the grains, sequentially, with abrasive paper from grit numbers 80 to 180. The dust, dirt that comes out during the sanding process should be totally removed. We recommend applying 1-2 coats of Sleek Base Colour for extending the life of the topcoat and preventing photo-degradation of wood. Apply 2 coats of Sleek XT 2 pack PU Sealer, after mixing base and hardener in the ratio 8:1 (by volume) by brush / spray. Allow 6-8 hours drying time. Sand using abrasive paper grit no. 320 and wipe clean.Apply 2 coats of Sleek XT 2 pack PU Topcoat by brush / spray, after mixing base & hardener in the ratio 8:1 (by volume) with 6-8 hours drying time between coats. Inter-coat sanding using abrasive paper grit number 400. Allow to dry overnight after second coat.
Sleek Thinners are designed to give the best results when used along with Sleek range of Wood Coatings. These are available as NC Thinner, Melamine & PU Thinners for brushing and spraying and can be selected based on requirement at site.
Contact your nearest dealer or our customer care number for more details.
Sleek Base is a basecoat for exterior woodwork with translucent pigments and anti-fungal properties that protect the surface, from harsh effects of Sunlight, rain and Fungal attack, at the same time add to its beauty. It is available in 14 natural wood colours that add depth to the substrate. Sleek Base increases the life of all types of clear topcoats for exterior. It also provides protection against warping/cracking of wood.
Surface Preparation & Application:
Sand the wooden substrate along the grains, sequentially, with abrasive paper from grit numbers 80 to 180. The dust, dirt that comes out during the sanding process should be totally removed.Apply 1-2 coats of Sleek Base colour. Allow 48 hours drying time. Sand gently using a scrub pad to remove any dust that may have settled on the paint film. Apply second coat. After drying Sleek Base can be over-coated using appropriate topcoat for longer life.
Sleek XT single pack PU Topcoat is a top quality product for the protection of all types of exterior wood work. Based on a modified PU binder and fortified with UV absorbers, it offers medium term protection for all types of exterior joinery under normal exposure conditions.
Surface Preparation & Application:
Sand the wooden substrate along the grains, sequentially, with abrasive paper from grit numbers 80 to 180. The dust, dirt that comes out during the sanding process should be totally removed. Apply 2 coats of Sleek XT single pack PU topcoat by brush / spray with 6-8 hours drying time between coats. Intercoat sanding using abrasive paper grit no. 320.
Indigo Sleek Anti-Termite Solution is a clear wood preservative designed to penetrate wood and kill termites as well as other wood boring insects resulting in long lasting protection.
Surface Preparation & Application:
Remove all dust and wipe the surface clean using NC Thinner or Mineral TurpentineApply one coat of Sleek Anti-Termite solution by brush/spray/muslin cloth. You can also use injection method for better penetration.Allow 12 hours drying time.You can apply more coats, if necessary, depending on the severity of the attack.
Sleek Interior Wood stain is a penetrating stain based on complex dyes dissolved in fast evaporating solvents. The wood stain has to be topcoated using an appropriate lacquer to give long lasting appearance for years to come.
Surface Preparation & Application:
Sand the wooden substrate along the grains, sequentially, with abrasive paper from grit numbers 80 to 180. The dust, dirt that comes out during the sanding process should be totally removed.Apply 1-2 coats of Sleek Interior Wood stain by rag cloth, spray or brush depending on the depth of colour required. Allow 30 minutes drying time. Sleek Wood stain must be over-coated using appropriate topcoat for longer life.
Indigo Acrylic Laminate is an acrylic latex based paint which gives rich heen finish. It is suitable for both interior & exterior applications.
Surface Preparation & Application:
Clean the surface of loose paint, dust and grease. Scrub vigorously with wire brush to remove algae, fungus and moss growth, especially on horizontal surfaces prone to water stagnation. Seal cracks with a 1:3 mixture of cement and sand. Use of Indigo Polymer Putty is highly recommended. Allow 3 months curing prior to painting for newly plastered surfaces. Apply one coat of Indigo Wall Primer on the plastered surface. Follow with 2 coats of Indigo Acrylic Laminate, obtained by thinning 1 litre of laminate with 300 ml of water. 3 Coats are recommended for horizontal surfaces like ledges, sun-shades, etc. Apply with brush, roller or spray keeping 4-6 hours interval between coats. Suitable for both Interior & Exterior application.
Indigo PU (Polyurethane) based Super Gloss Enamel is an all surface solvent based enamel that protects your wood and metal. It is designed to keep interior & exterior surfaces beautiful for long with better Non-yellowing property compared to traditional synthetic based enamels.
Surface Preparation & Application:
Wipe the surface clean to make it free from dust, dirt, grease etc. Sand the surface with abrasive paper grit no. 180. Wipe clean and use an appropriate primer to prime the surface. Dents & imperfections can be filled using appropriate fillers which should then be sanded and primed again. One liter of Indigo PU Super Gloss Enamel can be thinned down with 150ml of good quality turpentine for brushing consistency. Apply two coats giving an interval of 4-6 hours between coats.
