Ambala, Haryana, India GST : 06AADCJ9848D1ZE
Our Product / Services
Our product range comtains a wide range of L Shape Autopsy Table, Nirmal Quadriceps Exercise Table, traction treatment table, Vibrating table and Electromatic OT Table
Strong stainless steel design using heavy gauge good quality stainless steel. "l" shape design which comprises table (approximate dimension length 90 inches x width 30 inches x height 36 inches) and dissection wing (length 60 inches x width 30 inches x height 38 inches) with base cabinet. Base cabinet provided under the table to permit storage of items. Deep and large double bowl stainless steel sink with rounded corners. Sloping work surface to drain into the integral sink. Two piece construction for easy installation and flexibility for room cleaning and washing. Hot and cold water flow control. Suction facility. Solid stainless steel sliding body supports. Stainless steel head rest. Measurement scale on one side. Sprinkler for water spraying. Exit drainage system. Table and dissection wing mounted on stainless steel tubular stand. No revets or bolts so that work space is smooth and bacterial growth is avoided.
Designed for effective administration of progressive resistance exercise to the knee joints muscle groups. Both Quadriceps and Hamstrings can be exercised with out changing the position of the patients. Resistance bar is caliberated so that resistance can be varied from 12 and 34 and maximum without adding weight, the unit consists of foam padded seat with padded back rest. Table size 70cm x80cm x120cm high. The torque unit consists of two lever arms one of which hold the weight while the other provide contact with the patient. The exercising of the opposite leg is done by the lifting of the torque unit from its bracket and placing it on the other end of the table.By changing angle between the two arms, maximum or minimum resistance can be given at any point in the range. Comes with 6kg weights.
Salient features : a newly improved traction table suitable for lumber or cervical traction this table can also be used for other treatment instruments the table is very sturdy with a 24" wide top the table is fitted with 'non friction' rolling lumber section top for smooth efficient traction a mounting board is provided for convenient placement of traction machine the table top elegant by thick upholstered id 72" (183cm) long the overall length of the table is 92" approx. The mounting board is fitted with leveling device and provided with non skid pad
Vibrating Table The Vibrating table is entirely constructed of thick steel. The table top is made of thick mild steel plate and has stops along its edges to prevent moulds from walking off the table during operation. A cross arm adjustable on a vertical rod at the centre of the table is provided to hold the moulds while operating the table. The variable pitch pulley arrangement permits the variation of frequency between maximum of 3600 vibrations down to 2600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency. The vibrator is mounted on cushioned steel vibrating deck. A switch is provided for starting the motor. Operation on 440 V, three phase, A.C. supply.
equipped with imported electric actuators for smooth & effortless working of the table. It ensures the actuators working in a constant speed without any noise & is designed to run even at low voltage to carry on the surgery. Technical Constraints Top Dimension : L 1930 XW 553 mm Height Adiustment : 762 mm -1012 mm Trandelenburg Reverse : 30° 25° Lateral Tilt : 20° 20° Kidney Elevator : 150 mm Back Rest (up Down) : 80° 25° Leg Rest (up Down) : 15° 90° Head Rest (up Down) : 20° 60° Power Supply : 24v Dc Battery Backup (Optional) : 2-3 Hours Key Structure - The table has been made from acid proof, stainless steel (the face of the table is easy to clean and immune to disinfection agents) Strong & rust free base of stainless steel is provided to make the working conditions pleasant for the doctors & nurses. - Orthopedic attachment (hips and legs support) including the patient's pelvis support and legs support enables the limbs strain performing. Design of the Orthopedic attachment & eccentric column provides monitoring of the limbs with the C-ARM during the operation. - The various positions such as Up-Down movements, Trendelenburg Reverse Trendelenburg, Lateral Tilts, Flex- Reflex, Chair Position as realized by remote control. - Leg section & head section are interchangeable.
Table top is made of strong ms steel framework with SS sheet top. The whole top can be tilted to trendelenberg and reverse trendelenberg with help of lever handle. Table legs of ERW tubing mounted on 10 cm dia swiveling castors with two breaks. The table is complete with following accessories: chrome plated litholomy rod and anesthesia screen. SS kidney bridge and arm board finish in Epoxy powder coated.
Constructed from ms rectangular steel tube. Adjustable head section. Leg section movable on castors, two with brakes. Top is upholstered and covered with water proof synthetic material. Complete with SS bowl 32 cm. Dia., Standard padded leg holders. Finish in epoxy powder coated. Size | 1830 L x 610 W x 800 H mm