Other Products / Services #368583

Features:

• Trainer control panel is provided in 40X40mm Aluminum profile rack with sturdy table top flat panel.
• It has 5 nos of ABS plastic panel mounted on the aluminum rack with mimic diagram of components
• All input & output are terminated in 4mm shrouded connector and 4mm banana cable is provided for experiments.
• 1 Ph Motor, Alternator & Sync Panel (1 No)
• 1 phase Multifunction Panel(1 No)
• AC Voltmeter Meter panel (1 No)
• AC Ammeter panel (1 No).
• IGBT Controlled AC Motor Drive (VFD) panel(1 No).
• 3 Phase Induction Motor

Features:

• Output Range Variable 0-30 V/2A.
• Facility to preset both voltage and current limit desired by the user before DC output is turned on
• CV/CC indicted by LED's
• Automatic overload and short circuit protection.
• Two meters to read Voltage and Current.

• Dual Output Range Variable 0-30V/2A.
• Facility to preset both voltage and current limit desired by the user before DC output is turned on
• CV/CC indicted by LED's
• Automatic overload and short circuit protection.
• Four meters to read Voltage and Current.

Features:

• Dual Output Range Variable 0-30V/2A.
• Facility to preset both voltage and current limit desired by the user before DC output is turned on
• CV/CC indicted by LED's
• Fixed +5V/1A & +/-15V/1A
• Automatic overload and short circuit protection.
• Four meters to read Voltage and Current.

• 10 Logic Level Inputs & 10 LED for output indication.
• Fixed Clock generation of 1Hz, 10Hz, 100Hz, 1KHz, 10KHz, 100KHz & 1MHz.
• Logic Pulsar, Logic Probe, Potentiometers of 1K, 10K 100K
• Bread Board of 1260 tie points
• Sine, Square and Triangular output waveform from 0-200Khz.
• Fixed DC, Variable DC, AC power supply.
• All interconnections are made using 2mm banana Patch cord.

• piggy bag modules compatible of xilinx 9572 cpld , 95108 cpld, spartan xc3s50 fpga and xc3s400 fpga
• 16 toggle input switch and 16 output with led indication
• onboard 4 digit seven segment display, 16x1 lcd and 4x4 matrix keyboard
• on-board isp programmer for piggy bag modules
• clock generator generating 10mhz, 5mhz, 1mhz, 100 khz & 100 hz.
• in-built power supply of +5v/1.5a, 12v/250ma

• provided with 1hz. To 10 khz sine wave generator with amplitude adjustable & square wave(ttl) generator.
• one fiber optics led having peak wavelength of emission 660nm transmitter.
• one fiber optic photo detector receiver
• on board analog & digital drivers, ac amplifiers, comparator.
• on board 4th order butterworth 3.4 khz cut-off frequency.
• fo voice link using microphone & speaker
• on board serial pc to pc link using 9 pin d-type connector.

• Provided with 1Hz. To 10 KHz sine wave generator with amplitude adjustable & Square Wave(TTL) generator.
• Two Fiber Optics LED having peak wavelength of emission 660nm &950nm Transmitter, Two Fiber Optic photo detector Receiver
• On board Analog & Digital Drivers, AC Amplifiers, Comparator
• On board 32K, 64K, 128K, 1M Clock generator
• On board 16 bit PRBS generator and White Noise generator Output
• Modulation Techniques using PCM Modulation & Demodulation using codec IC.
• 16 channel TDM multiplexing & Demultiplexing technique with Manchester coding & decoding.
• Bit error rate measurement using 8 bit counter with LED indication upto 255 count.
• On board 4th order Butterworth 3.4 KHz cut-off frequency.
• Two channel voice link using phone & speaker(A-Law).
• On board Serial PC to PC link using 9 Pin D-type connector.

Features:

• Provided with 1Hz. To 10 KHz sine wave generator with amplitude adjustable & Square Wave(TTL) generator.
• One Laser Fiber Optics LED having peak wavelength of emission 660nm Transmitter, One Fiber Optic photo detector Receiver
• On board Analog & Digital Drivers, AC Amplifiers, Comparator.
• On board 4th order Butterworth 3.4 KHz cut-off frequency.
• On board Serial PC to PC link using 9 Pin D-type connector.

Features:

• L1 Frequency, C/A code, 51-channel High SensitivityUp to -158 dBm tracking, superior urban performances
• Cold Start, Warm Start, Hot Start operation
• 9600 baud rate Serial Transmission
• Built in RS232 Level Converter (MAX232) provided in 9 Pin D type connector
• Windows based software support GPS Status, Signal Level, Sky chart constellation of SV.

• Dual band 900 / 1800 MHz GSM / GPRS Modem.
• Onboard RS-232 & USB connector for PC Communication
• 20 Membrane keys with multifunctional operation.
• GLCD 128x64 for display, RTC, Mic and Speaker interface.
• SMA antenna connector with antenna.
• Sliding / fixed landing SIM holder (3.3V/5V SIM interf.)
• Remote control by AT commands (according to GSM 07.07 and GSM 07.05)
• Maximum output power 2W for GSM 900: 1W for GSM 1800

• Two Channel CDMA (DSSS and FHSS) Techniques
• 16Kbps, 8 Kbps, 4Kbps of Data rate, 8 bits World Length
• Data Format is NRZ (Non Return to Zero)
• PN Sequence Generators Chip Clock : 240 KHz, 120 KHz, 60 KHz, 16KHz, 8KHz, 4KHz with Maximal length sequence & Selectable through feedback taps in LFSR.
• 100 KHz for mark and 50 KHz for space BFSK frequencies.
• Sinusoidal Frequency synthesizer Output
• Frequency synthesizer frequencies : 1.6 MHz, 1.4 MHz, 800 KHz, 400KHz.
• Hopping channels are Four with variable selectable for slow and fast hopping.

Features:

• Trainer having control panel should provided in 40X40mm Aluminum profile rack with sturdy table top flat panel.
• Should have 1phase power supply with DC Panel
• Should have DC Voltmeter & Ammeter panel .
• Should have Controller panel.
• Should supply with Brushless DC Motor.

Features:

• Trainer having control panel should provided in 40X40mm Aluminum profile rack with sturdy table top flat panel.
• Should have 1 ph. Supply, Multifunction Panel
• Should have IGBT Controlled AC panel.
• Should have Voltmeter & Ammeter panel.
• Should supply with Induction Motor

Features:

• Motor Generator Trainer having control panel should provided in 40X40mm Aluminum profile rack with sturdy table top flat panel.
• Should have 3phase DOL starter 4pole MCB, contractor & relay panel
• Should have 3 phase multifunction meter panel.
• Should have FWD/REV, STAR/DELTA Switch panel.
• Should have 1 ph. Motor, Voltmeter & Ammeter Panel.
• Should have SCR controlled variable DC panel.(2nos)
• Should have Instrumentation panel.
• Should have 1 Phase AC/DC Resistive Load panel.
• Should supply with DC Motor Coupled with 3 Phase Induction Motor or 1 Phase Induction Motor or 1 Phase Universal Motor or 1 Phase Synchronous Motor or 3 Phase Salient Pole AC Motor or 1HP DC Generator

• Resistive Pressure Transducer with Pressure of 0-300mm hg / 6psi
• Primary Excitation voltage of 5V DC on board provided.
• On-board 41/2 Digital Panel Meter provided using AD7135.
• Pressure generation and Monitor using a Pressure gauge.
• Onboard Instrumentation Amplifier provided

• Resistive cantilever type Load cell is used to measured up to 3 KGs.
• Primary Excitation voltage of 12V DC provided on board.
• On-board 41/2 Digital Panel Meter provided using AD7135.
• Onboard Instrumentation Amplifier provided
• Weights can be verified by Physical counting of weights

• Ultrasonic type Transducer
• Resonant Frequency of the Transducer is 40 KHz.
• Excitation Source 40 KHz Frequency provided on board.
• Measurement Range From 25 cm to about 6 meter.
• Onboard Instrumentation Amplifier provided

• LVDT Transducer with transparent enclosure having Displacement of 5mm
• Primary Excitation voltage of Sine wave 1V p-p
• On-board Digital Panel Meter provided using AD7135
• Screw Gauge for reference displacement reading
• On board 1Khz Sine wave generator for excitation.
• Onboard Instrumentation Amplifier provided

Features:

• K-type Thermocouple is used to measurement Temperature up to 100C
• On-board 41/2 Digital Panel Meter provided using AD7135.
• Onboard Instrumentation Amplifier provided
• Thermometer for measurement of temperature
• Water Heater with AC mains Chord provided

• PT-100 Type RTD sensor is used to measurement Temperature up to 100C
• On-board 41/2 Digital Panel Meter provided using AD7135.
• Onboard Instrumentation Amplifier provided
• Thermometer for measurement of temperature
• Water Heater with AC mains Chord provided

• Capacitive Level Transducer to Measure Level up to 100mm.
• On-board 41/2 Digital Panel Meter provided using AD7135.
• Onboard Instrumentation Amplifier provided
• 100mm Scale is provided for level measurement
• Plastic container with outlet Tap is provided for Water Storage

• Magnetic Pick-up & Photo Pick up Transducer is also used
• On-board Digital RPM Panel Meter provided
• Onboard Instrumentation Amplifier provided
• 6V DC Motor with necessary attachment is provided

• Resistive Transducer using multi turn potentiometer to measure Angle from 0 to 360.
• Protractor for angle measurement
• Onboard Instrumentation Amplifier provided

• AD590 /Thermistor Sensor is used to measure temperature up to 100C
• Onboard Instrumentation Amplifier provided
• 12V Heater provided on board.

• Simulated blocks like dead time (transportation lag), integrator, time constant, error detector and gain.
• PID Controller Prop: Band 5% to 50% (Gain 2-20), Integral time: 10msec-100msec, Derivative time : 2-200msec
• Built-in signal sources Value of -1V to +1V, Square wave & Triangular of 1V p-p (min) at 40Hz, Built-in 3 digit DVM for DC measurements

• Simulated first, second and third order system of type-0 and type-1
• Calibrated variable gain amplifier (Resolution 1:1000)
• Built-in signal sources of Square wave and Triangular Frequency of 45-90Hz With Amplitude 0-2.5V.
• Uncommitted amplifier for phase adjustment, Provision for disturbance inputs.

• Synchro transmitter-receiver pair with calibrated dials enclosed In see through metal cabinet
• Locking system for receiver rotor, Receiver use as control transformer
• Built-in balanced demodulator circuit, Panel meter for ac/dc voltages

• Temperature controller with facilities for P. I, D and relay control blocks.
• Operating temperature: Ambient to 900C.
• Separate controls for P, I, D channel gains, Two settings for relay hysteresis.
• Fast 25W oven fitted with IC temperature sensor.
• Digital display of set and measured temperature on 3 digit built-in DVM.

• Simulated electronic relay using high speed ICs.
• Simulated 2nd order linear plant. Facility for displaying x and x signaling.
• Dead zone variable from 0-600mV, Hysteresis variable from 0-500m
• Built-in Signal source- Sine and Square Amplitude: 0-1V (min) with Variable Frequency: 10 to 1000Hz.

• Speed control of a 12V, 4W permanent magnet d.c. motor enclosed In see through Metal cabinet
• Speed range: 0 to 3000 rpm (typical), Opto-interrupter based speed sensing.
• 4-digit speed display in rpm, Electronic tachogenerator for feedback.
• Separate unit for motor in a see-through cabinet, Smooth, non-contact eddy current brake for loading.
• Built-in 3 digit DVM for signal measurements.

• Simulated uncompensated system having adjustable damping. Peck percent overshoot Mp, variable from 20% to 50%, and steady state error variable from 50% to 0.5%
• Compensation network implementation through built-in variable gain amplifier. Gain is adjustable from 1 to 11.
• Built-in square and sine wave generators for transient and frequency response studies. Frequency adjustable from 25Hz 800Hz (approx).

• Single stepping and free running modes of operating with speed variation and direction reversal internal TTL circuit.
• 360O motion Servo-Potentiometer position-pickup for motor dynamics.
• Operation through microprocessor kit-sample control programs provided.
• Stepper motor enclosed in see through metal cabinet, Torque 3 Kg-cm, Step angle 1.8 O, Power 12V, 1A/ phase

• 2-phase a.c. servomotor 12V/50Hz per phase enclosed in see through metal cabinet.
• Small generator for loading.
• 4-digit speed display, 3-digit time constant display.
• 3 digit r.m.s. voltmeter, 3 digit d.c. panel meter.

• Position control of a 12V, 1A d.c. gear motor (50rpm) with calibrated dials coupled with tacho-generator enclosed in see through metal cabinet
• Provision for positive and negative tachogenerator feedback.
• Tacho constant: 2V/ 1000 rpm approximately.
• Calibrated dials for reference and output position: resolution 1 degree
• P based waveform capture card.
• Built-in 3 digit DVM for signal measurements.
• Built-in step signal and IC regulated power supplies for electronic circuit.
• Servo-potentiometer with full 360 degree rotation.
• Separate unit for motor in a see-through cabinet.

• 2-phase servomotor 12V/ phase, 50Hz, 10W with calibrated dials coupled with Potentiometer enclosed in see through metal cabinet.
• Power amplifier.
• Servo potentiometer type error detector.
• In-built 10.00V (rms) panel meter.
• P based waveform capture card.

• light sensor like photoconductive cell, photovoltaic cell, phototransistor, pin photodiode
• on board filament lamp light source
• signal conditioning circuitry : power amplifier, current amplifier, dc amplifier, comparator, electronic switch, buffer
• on board rotary, slide potentiometers, relay & led circuits provided.

• Speed control of a 30V/2A, permanent magnet d.c. motor coupled
• With tachogenerator enclosed in see through metal cabinet.
• Speed range: 0 to 2000 rpm (typical), Opto-interrupter based speed sensing.
• 4-digit speed display in rpm., Electronic tachogenerator for feedback.
• Separate unit for motor with 2Kg Spring Balance provided for loading.
• Built-in 3 digit DVM for signal measurements, 3 digit Current Meter.

• 3 axis standalone cnc controller with spindle and mpg support
• 4.3" tft screen, resolution ratio480*272 with 17 operational keys.
• support the usb flash disk to read the g code
• be equipped with mpg port and support digital display mpg as well as support the general mpg in the market
• support the panel key with single-axis manual operation, manual step and continued operations.
• machine dimensions: 610485395mm
• experiment application: engraving, drilling & cutting for wood, bamboo, pcb, pvc, pmma, plastics, abs etc.

.

• Pre-installed hand wheel
• PC based CNC system, high reliability, operate simple
• Connect with PC via network cable
• G code can compatible with PLC
• Safe and reliable whole shields shell
• High quality 2 axis step motor, high torque brushless motor
• Safety electrical components of high quality and fast plug

• Internal 300Hz to 3.4KHz Sinewave generator
• 2 Nos. of Balanced Modulator with band pass filter (1MHz) & 1 No. of balanced modulator (455KHz)
• Ceramic band pass filter, Carrier Frequency of 1MHz
• Audio output amplifier with speaker
• Transmitting output using Telescopic Antenna or Directly using Cord to Receiver.

• Frequency range of 525 to 1625Khz.
• Receiver CKT consist of RF Amplifier, Mixer, Local Oscillator, BFO, IF amplifier-1, IF amplifier-2.
• Diode detector for DSB & Product detector for SSB.
• Audio output amplifier with Speaker
• Receiving Input using Telescopic Antenna or Directly using Cord from Transmitter

• Internal 300Hz to 3.4KHz Sinewave generator
• FM Modulation using VCO Modulator, Reactance Modulator & Varactor Modulator.
• Transmitter Frequency to 455 KHz.
• FM Demodulator using Detuned Resonant detector, Quadrature detector, Fooster Seeley detector, Ratio detector & PLL detector-1, PLL detector-2.
• Low Pass filter with cut off frequency of 3.4KHz.

• Two Nos. of Sine Wave generators provided from 200Hz to 10Khz
• Fixed Carrier Sine Wave Generators of 100 KHz and 200 KHz.
• On-board features Two Nos. of DSB-SC Modulator & Two Nos. of Balanced De-modulator
• On board Summing Amplifier & AC Amplifier Provided
• Two 2nd order Butterworth Low pass filter with cut off frequency of 10 KHz.

• Trainer having control panel should provided in 40X40mm Aluminum profile rack with sturdy table top flat panel.
• Should have 3phase DOL starter 4pole MCB, contractor & relay panel
• Should have 3 phase multifunction meter panel (2nos), FWD/REV Switch panel.
• Should have Transmission Line Compensation panel.
• Should have 3 Phase Resistive Load panel, Inductive Load panel, Capacitive Load panel.
• Should have table top Simulated Transmission Line, table top Dimmer.