Kitek Technologies Private Limited

Airoli, Navi Mumbai, Maharashtra

Features:

• AM Detector Circuit, AM If Circuit, AM Amplifier Circuit.
• AM Mixer and Oscillator Circuit.
• FM Detector Circuit. First FM IF AMPLIFIER Circuit, Second FM iF AMPLIFIER Circuit.
• FM Radio Frequency Stages. AM Radio Section.
• Power output 8 14W Speaker.

Features:

• 10 Logic Level Inputs & 10 LED for output indication.
• Fixed Clock generation of 1Hz, 10Hz, 100Hz, 1KHz, 10KHz, 100KHz & 1MHz.
• Logic Pulsar, Logic Probe, Three Digit 7-Segment Display.
• Bread Board of 630 tie points
• One IC each of 7400, 7402, 7408, 7432, 7404, 7490, 7495, 7486, 7447 & Two Nos. of IC 747.
• 20 Pin Socket- 1No.
• Fixed DC +5V, 12V power supply.
• All interconnections are made using 2mm banana Patch cord.

• quad-band gsm/gprs 850/ 900/ 1800/ 1900 mhz
• built in rs232 level converter (max232) provided in 9 pin d type connector
• configurable baud rate
• sma connector with gsm l type antenna.
• built in sim card holder.
• built in network led, status led, power led
• inbuilt powerful tcp/ip protocol stack for internet data transfer over gprs.
• audio interface connector

.

• 4 LED for output indication.
• Bread Board of 630 tie points
• One IC each of 555, 741, LF398, MCT2E, Transistor, Diodes.
• Resistor & Capacitor bank, SPDT Relay, Speaker.
• Two 8 Pin Socket, Potentiometers of 1K, 10K 100K
• Sine, Square and Triangular output waveform from 0-200Khz.
• Fixed DC, Variable DC, AC power supply.
• All interconnections are made using 2mm banana Patch cord.

• 8 TTL/CMOS Logic Level Inputs with indicator LED for Logic Low & Logic High.
• 10 output LEDs for Logic level Indicators.
• Two digit BCD to 7 segment decoder.
• Fixed (TTL) Clock generator of 1Hz, 100Hz, 10KHz, 100KHz.
• Four Pulser Generator with Eight debounced Output.
• On-board two 10K Variable Potentiometer.
• On-board two BCD Thumbwheel Switch, Buzzer.
• On-board +12V SPDT Relay for Control application.
• Fixed DC Power Supply: +5V/1A, 12V/250mA, Variable DC Power supply of 0 to +15V/250mA output.
• Set of 2mm Banana Patch Cords.
• Should support DN series ready to use Electronics board.

• Provides Sine waveform output of 250Hz, 500Hz, 1 KHz, and 2 KHz. With Amplitude adjustments of 0 - 5Vp-p.
• On board 0 to 5V DC source with Amplitude adjustments.
• Sampling rate of 32 KHz/channel with 8KHz. Channel Identification Signal.
• On-board features Four Analog Channels TDM Multiplexing/De-multiplexing
• Clock regeneration at receiver using PLL.
• 4th order Butterworth Low pass filter with cut off frequency of 3.4 KHz.

• Features:
• indication provided for line in, hook, tone and ringer.
• tone and pulse dialers are provided
• tone frequency is of 430hz.
• one dot line connection port & handset connection port
• 4 x 3 matrix key board & keypad contains 0 - 9, # & * mute, redial, flash and on/off hook switches.
• ringer volume control provided using potentiometer

.

• Type of control PID Control unit Digital indicating controller , Temperature sensor Type RTD, PT100
• Heating control Proportional power controller (SSR), Input 4-20 mA, Capacity 20 A
• Heater Type 3 bulb , Capacity 300 W
• Process Chamber: Fitted with bulb & Cooling Fan.
• 230 +/- 10 VAC, 50 Hz, 1 phase with On/Off Switch

• RF Input 950-2150 MHZ with Input Impedance : 75 Ohm
• RF Output 470MHz to 862MHz (approx)
• Ku & C band type LNB are provided.
• 6" Dish Antenna with Dish Input F type Connector
• RCA type Composite Video Output, Audio Output, TV Output.
• PAL/NTSC Video Output
• IF Frequency Bandwidth 27MHz-36MHz
• Video Output level 1Vpp (75 load)
• 352 x 288 Image Resolution
• Controls Power, Menu, Channel Up/Down OK, Left, Right
• 17 nos of Test Points provided.
• Power Supply 110V - 260V AC, 50Hz/60Hz
• Dish Antenna & LNB Should be mounted on Alluminium profile.

• features:

  • type of control pid control unit digital indicating controller, temperature sensor type rtd, pt100
  • heating control proportional power controller, (ssr), input 4-20 ma, capacity 20 a.
  • heater type electrical 2 coil, capacity 3 kw.
  • rotameter 6-200 lph., process tank capacity 0.5 lit, insulated.
  • 230 +/- 10 vac, 50 hz, 1 phase with on/off switch.

• Type of control PID Control unit Digital indicating controller, Input Type 4-20mA
• Level transmitter Type Electronic, two wire, Range 0500 mm, Output 420mA,
• I/P converter Input 4-20mA, Output 3-15 psig
• Control valve Type Pneumatic, Size 1/2", Input 315 psig, Air to close, Char. Linear,
• Rota-meter 10 - 200 LPH
• Pump Fractional horse power, type submersible with Sump Tank
• Process tank Transparent, Acrylic, with 0-300mm graduated scale
• Air filter regulator 0-2.5 kg/cm2 , Pressure gauge 0-2.5 kg/cm2, 0-7 kg/cm2.
• 230 +/- 10 VAC, 50 Hz, 1 phase with On/Off Switch.

• Type of control PID Control unit Digital indicating controller , Input Type 4-20mA
• Pressure transmitter Type Two wire, Range 05 bar, Output 420 mA
• I/P converter Input 4-20mA, Output 3-15 psig
• Control valve Type Pneumatic, Size 1/2", Input 315 psig, Air to close, Char. Linear, MS Process tank Pressure vessel with output valve.
• Air filter regulator 0-2.5 kg/cm2 , Pressure gauge 0-2.5 kg/cm2, 0-7 kg/cm2
• 230 +/- 10 VAC, 50 Hz, 1 phase with On/Off Switch.