Kitek Technologies Private Limited

Airoli, Navi Mumbai, Maharashtra

• Piggy Bag Modules compatible of XILINX 9572 CPLD , 95108 CPLD, SPARTAN XC3S50, XC3S400, SPARTAN6, Altera Cyclone2 FPGA.
• 16 Toggle Input Switch and 16 output with LED indication
• Onboard 4 Digit Seven Segment display, 16x1 LCD and 4x4 Matrix Keyboard
• On-board ISP Programmer for Piggy Bag Modules
• Clock generator generating 10MHz, 5MHz, 1MHz, 100 KHz & 100 Hz.
• In-Built Power Supply of +5V/1.5A, 12V/250mA

• Single stepping and free running modes of operating with speed variation and direction reversal internal TTL circuit.
• 360O motion Servo-Potentiometer position-pickup for motor dynamics.
• Operation through microprocessor kit-sample control programs provided.
• Stepper motor enclosed in see through metal cabinet, Torque 3 Kg-cm, Step angle 1.8 O, Power 12V, 1A/ phase

• Features:
• Semi/Fully Automatic Washing Machine
• Mechanical Controls 30 Minutes Timer, Wash/Spin Control
• 6 Liter Capacity Machine
• Fault Switches for Wash motor, Spin Motor, Lid opening, Buzzer etc
• All faults are mounted on PCB with Enclosure

• Synchro transmitter-receiver pair with calibrated dials enclosed In see through metal cabinet
• Locking system for receiver rotor, Receiver use as control transformer
• Built-in balanced demodulator circuit, Panel meter for ac/dc voltages

• 10 Logic Level Inputs & 10 LED for output indication.
• Fixed Clock generation of 1Hz, 10Hz, 100Hz, 1KHz, 10KHz, 100KHz & 1MHz.
• Logic Pulsar, Logic Probe, Potentiometers of 1K, 10K 100K
• Bread Board of 1260 tie points
• Sine, Square and Triangular output waveform from 0-200Khz.
• Fixed DC, Variable DC, AC power supply.
• All interconnections are made using 2mm banana Patch cord.

• 3 axis standalone cnc controller with spindle and mpg support
• 4.3" tft screen, resolution ratio480*272 with 17 operational keys.
• support the usb flash disk to read the g code
• be equipped with mpg port and support digital display mpg as well as support the general mpg in the market
• support the panel key with single-axis manual operation, manual step and continued operations.
• machine dimensions: 610485395mm
• experiment application: engraving, drilling & cutting for wood, bamboo, pcb, pvc, pmma, plastics, abs etc.

.

Features:

• Provided with 1Hz. To 10 KHz sine wave generator with amplitude adjustable & Square Wave(TTL) generator.
• One Laser Fiber Optics LED having peak wavelength of emission 660nm Transmitter, One Fiber Optic photo detector Receiver
• On board Analog & Digital Drivers, AC Amplifiers, Comparator.
• On board 4th order Butterworth 3.4 KHz cut-off frequency.
• On board Serial PC to PC link using 9 Pin D-type connector.

Features:

• L1 Frequency, C/A code, 51-channel High SensitivityUp to -158 dBm tracking, superior urban performances
• Cold Start, Warm Start, Hot Start operation
• 9600 baud rate Serial Transmission
• Built in RS232 Level Converter (MAX232) provided in 9 Pin D type connector
• Windows based software support GPS Status, Signal Level, Sky chart constellation of SV.

• features:

  pcb artwork film maker
• pcb curing machine(oven)
• photo resist dip coating machine
• double sided u.v.exposure unit
• etching machine
• pcb drilling machine
• pcb shearing machine
• roller tinning machine
• dye/developer machine
• pcb layout software

.

• 8051 CPU operating @ 10/12 MHz.
• 8K user RAM with Battery Backup, 16K bytes monitor EPROM
• Peripherals like 2x 8255 brought, 8253, 8251, RS-232 interface
• 25 Keys Hexadecimal Keyboard and 6 digit 7-segment display using 8279
• In-Built Power Supply of +5V/1.5A, 12V/250mA

• Frequency range of 525 to 1625Khz.
• Receiver CKT consist of RF Amplifier, Mixer, Local Oscillator, BFO, IF amplifier-1, IF amplifier-2.
• Diode detector for DSB & Product detector for SSB.
• Audio output amplifier with Speaker
• Receiving Input using Telescopic Antenna or Directly using Cord from Transmitter

• Pre-installed hand wheel
• PC based CNC system, high reliability, operate simple
• Connect with PC via network cable
• G code can compatible with PLC
• Safe and reliable whole shields shell
• High quality 2 axis step motor, high torque brushless motor
• Safety electrical components of high quality and fast plug

• provided with 1hz. To 10 khz sine wave generator with amplitude adjustable & square wave(ttl) generator.
• one fiber optics led having peak wavelength of emission 660nm transmitter.
• one fiber optic photo detector receiver
• on board analog & digital drivers, ac amplifiers, comparator.
• on board 4th order butterworth 3.4 khz cut-off frequency.
• fo voice link using microphone & speaker
• on board serial pc to pc link using 9 pin d-type connector.

Features:

• On Board synchronized RF carrier signal generators with frequencies of 120 KHz, 200 KHz.
• 8 bit Digital Data generator to generate any binary input word using 8-way DIP Switch
• On board two Balanced Modulator Circuit
• On board Demodulator PLL Detector Circuit

features:

• trainer having control panel should provided in 40x40mm aluminum profile rack with sturdy table top flat panel.
• should have 3phase dol starter 4pole mcb, contractor & relay panel
• should have 3 phase multifunction meter panel .
• should have circuit breaker panel, switch panel, bus bar panel, fuse panel.
• should have industrial socket panel, analog voltmeter & ammeter panel.
• should have kwh meter 1 phase kwh meter, 3 phase kwh meter.
• should have lamp load panel.

.

• Internal 300Hz to 3.4KHz Sinewave generator
• 2 Nos. of Balanced Modulator with band pass filter (1MHz) & 1 No. of balanced modulator (455KHz)
• Ceramic band pass filter, Carrier Frequency of 1MHz
• Audio output amplifier with speaker
• Transmitting output using Telescopic Antenna or Directly using Cord to Receiver.

• Dual band 900 / 1800 MHz GSM / GPRS Modem.
• Onboard RS-232 & USB connector for PC Communication
• 20 Membrane keys with multifunctional operation.
• GLCD 128x64 for display, RTC, Mic and Speaker interface.
• SMA antenna connector with antenna.
• Sliding / fixed landing SIM holder (3.3V/5V SIM interf.)
• Remote control by AT commands (according to GSM 07.07 and GSM 07.05)
• Maximum output power 2W for GSM 900: 1W for GSM 1800

• Trainer having control panel should provided in 40X40mm Aluminum profile rack with sturdy table top flat panel.
• Should have 3phase DOL starter 4pole MCB, contractor & relay panel
• Should have 3 phase multifunction meter panel (2nos), FWD/REV Switch panel.
• Should have Transmission Line Compensation panel.
• Should have 3 Phase Resistive Load panel, Inductive Load panel, Capacitive Load panel.
• Should have table top Simulated Transmission Line, table top Dimmer.

Features:

• Motor Generator Trainer having control panel should provided in 40X40mm Aluminum profile rack with sturdy table top flat panel.
• Should have 3phase DOL starter 4pole MCB, contractor & relay panel
• Should have 3 phase multifunction meter panel.
• Should have FWD/REV, STAR/DELTA Switch panel.
• Should have 1 ph. Motor, Voltmeter & Ammeter Panel.
• Should have SCR controlled variable DC panel.(2nos)
• Should have Instrumentation panel.
• Should have 1 Phase AC/DC Resistive Load panel.
• Should supply with DC Motor Coupled with 3 Phase Induction Motor or 1 Phase Induction Motor or 1 Phase Universal Motor or 1 Phase Synchronous Motor or 3 Phase Salient Pole AC Motor or 1HP DC Generator

• MS powder coated Sump tank with flow.
• MS powder coated Measuring tank.
• Mercury Manometers(Differential).
• Each line provided with flow control value for setting of different flow rates.
• Pressure tubes of different pipe lines are connected to common manometer through cocks.
• Easy to operate and replacement of Venturimeter & Orifice meter.
• Flow control value at the end of each line assures full running of pipe.
• Differential manometer of 300 mm length with mercury

• features:

  • provides rf generated output of approx.750 mhz with output adjustment.
  • provides tone generated output of approx.1 khz with output adjustment.
  • forward and reverse direction coupler
  • antenna rotation of 0-360 with antenna resolution of 1
  • receiving antenna is folded dipole type with reflector and digital meter
  • digital meter is provided for forward & reverse indication.
  • twenty one different types of antennas are
  • goniometer is provided on main panel with slider type matching stub provided

• storage tank ms powder coated.
• collecting tank ms powder coated capacity approx. 60 liters, fitted with drain valve 1 size. Manometer tube with calibrated marking scale.
• monoblock pump : monoblock, 1ph, hp pump shall be provided with the set-up which shall be mounted on the base plate. Necessary piping with by-pass valve and suction piping are provided. The connection for the test equipment is made by flexible house pipe.
• differential manometer of 300mm length with mercury.

• Metal Bar copper 25 x 430 mm long (approx)
• Insulating powder shell 200mm dia (approx)
• Cooling water chamber 100mm dia x 75 mm Long (approx)
• Control Panel consisting of Voltmeter, Ammeter, Dimmerstat, Digital Temperature Indicator with chromel alumel thermocouples

• Inner sphere diameter 100mm.
• Outer sphere diameter 200mm
• Heater-Nichrome wire sandwiched between mica sheets.
• Control Panel consisting of Voltmeter, Ammeter, Dimmerstat, Digital Temperature Indicator with chromel alumel thermocouples.

• H.P. pump to circulate water through the piping.
• MS powder coated Sump tank of 1000 mm x 300 mm x 400 mm capacity.
• MS powder coated Measuring tank of 300 mm x 300 mm x 500 mm height.
• Pressure gauge, Vacuum gauge, U-tube manometer 300 mm height.
• Differential manometer 300 mm, 45C, Single tube manometer

• Two Channel CDMA (DSSS and FHSS) Techniques
• 16Kbps, 8 Kbps, 4Kbps of Data rate, 8 bits World Length
• Data Format is NRZ (Non Return to Zero)
• PN Sequence Generators Chip Clock : 240 KHz, 120 KHz, 60 KHz, 16KHz, 8KHz, 4KHz with Maximal length sequence & Selectable through feedback taps in LFSR.
• 100 KHz for mark and 50 KHz for space BFSK frequencies.
• Sinusoidal Frequency synthesizer Output
• Frequency synthesizer frequencies : 1.6 MHz, 1.4 MHz, 800 KHz, 400KHz.
• Hopping channels are Four with variable selectable for slow and fast hopping.

• MS powder coated Sump Tank
• Specific Speed Approx. 19 RPM, Net Head 45m Approx.
• Discharge Approx. 820 LPH approx, Normal Speed 750 RPM.
• Power 1kw ( 5HP motor), Runner Diameter 250 mm, Number Of Buckets 16
• Brake Drum Diameter 200 mm.
• Centrifugal Pump set suitable for supply of water of size coupled to 5 HP induction motor 3 phase 400 V. A. C. supply.
• Starter switch, piping, foot valve, gate valve.

• Features:
• 89E516RD Microcontroller based stored program control having Memory of 72KB Program memory & 1KB Data RAM memory.
• No. of Subscribers Two DOT Lines, Four Extension Lines
• Line Section are Opto Isolated for Trunk Lines and 4 Extension Lines.
• Tone Generation like Dial Tone, Busy Tone, Ring Back Tone, Hold-on music etc.
• Speech Path is Fully Non- Blocking.
• Switch Faults : 8 Switch Faults are provided on board to study different effects on circuit.

Features:

• 0.5 HP Mono block cylinder.
• Universal Motor Free Vortex Flow
• Acrylic Vessel 200 x 300mm
• MS powder coated Sump tank.
• MS powder coated Measuring Tank.

• Air Filter, Isolating Valve, Regulator & Lubricator Unit (FRL Unit)
• Pressure Manifold with Four ON / OFF Valves for multiple connections
• Single Acting Cylinder
• Double Acting Cylinder

Features:

• Pipes Length of Pipes lm (approx).
• M. S. Pipe inside 5cm dia. approx, M. S. Pipe Middle 10cm dia (approx).
• M. S. Pipe Outer 10cm Control Panel consisting of:
• Voltmeter-0-200 Volts.
• Ammeter 0 2 Amp.

We are the main supplier of this product.

• AC Input 190 to 260 V10%, 50 Hz
• Load Output 230 V/ 2.5A
• Transformer Used Input 12 - 0 - 12 V, Outputs : 0, 190, 220, 240, 260 V, Battery charging: 0-18 V
• IC SG3524 PWM IC used for PWM Switching
• 4nos of IRF3205MOSFET for Switching
• 12V DC Battery.

• Central Heater - suitable capacity, with 100 mm dia. sandwiched between two copper plates
• 180 mm mica heater Sandwiched between two copper plates Cooing chamber with water circu ation arrangement.
• Specimen -6 to 20 mm thick, 180 dia.
• Glass wool bag insulation around the set-up
• A Control Panel comprising of-al Voltmeter - 0 - 200 Volts

• type of control pid control unit digital indicating controller, input type 4-20ma
• i to p converter input 4-20ma, output 3-15 psig
• control valve type pneumatic, size 1/2", input 315 psig, air to close, linear type
• rotameter 10-200 lph, pump submersible with sump tank
• flow measurement sensor, output 4-20ma.
• air filter regulator 0-2.5 kg/cm2, pressure gauge 0-2.5 kg/cm2 & 0-7 kg/cm2
• 230 +/- 10 vac, 50 hz, 1 phase with on/off switch.