Suitable for Charpy and Izod impact Tests on various materials.Rigid designs of machine frame and other parts assure minimum energy absorption during fracture which results in improved test accuracies.

• Variety of tests like Tension, Compression, Cross breaking / Bending, Shear, Linear Bonding / Gripping / Peeling strength of adhesives & tapes, etc. are conducted.
• Suitable for testing a wide range of materials like rubber, wood, plywood, plastic, rexins, ceramics, teflon, cardboard, latex, composites, ferrous metals, non-ferrous metals, etc. of various forms like round, flat, thread, wires, dumbells, fabric, belts, strips, ropes, etc.
• Wide range of Grips, Attachments & Special fixtures are available to suit variety of material and shapes.
• Continuous roll autographic "Load Vs Elongation" recorder.
• Elongation scale with least count 1 mm.
• Three measuring ranges for accurate testing.
• A number of straining speeds are available for proper selection.
• Machine with AC or DC drive motor is available.
• Various Models - Maximum Capacity from 200 N to 50 kN.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.
• Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.

• Vickers Cum Brinell Hardness Testing Machines ( Model : BV )
• Suitable for finding out Vickers / Brinell hardness of metals from soft to very hard.
• Push button control for load selection.
• A range of test loads for Vickers / Brinell - from 1 kg to 250 kg.
• Optical Magnifications - 35X, 70X & 140X available.
• A precision Diamond Indentor (136 pyramid) is used to make sharp indentations on the specimens / samples.
• Maximum Test height x Throat : 250 x 150 mm.
• Load accuracy well within 1% of nominal load value. Machine conforms to IS:1754.
• Computerized model is available .Computerized model has built in CCD and suitable advanced software. Hardness will be displayed on computer monitor automatically. Results printout can be taken.

Automatic Data capture, storage & graphic display.Recording, storage & retrieval of results & details.On line display of load & extension.Fully automatic, on screen calculations based on the delivered data.Out put to digital printer of test data, test results & graphs.Auto detection of over load, over travel & specimen break, on detection of the above conditions, the machine is automatically switched off.Load resolution - 0.01% of machine capacity for entire range.Accurate and Users friendly software & all other facilities mentioned under Model : TUN.

• Variety of tests like Tension, Compression, Tranverse, etc. are conducted.
• Continuous roll autographic "Load Vs Elongation" recorder.
• Suitable for testing a wide range of metallic materials.
• Extra (Optional) Accessories such as - Mechanical Extensometer, Load-Stabilizer, Attachments for Brinell test, Tensile test for shouldered & threaded, Single & Double shear test, Bolts-Nuts & Washer test, Rope test, Flat Belt test, Bend-Rebend test, 180 Bend test, Pull-Out test, etc. are available.
• Capacities from 100 kN to 2000 kN.
• Various Analogue Models - TUN-100, TUN-200, TUN-400, TUN-600, TUN-1000 & TUN-2000.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.

• This is a combined hardness testing machine used to measure hardness of metals & alloys of all kinds, hard or soft, whether round, flat or irregular in shapes.
• This machine is ideally suitable for laboratories, tool rooms, Heat treatment shops, R&D departments, inspection departments, casting & forging industries, educational institutions.
• Rockwell & Brinell method is used for checking hardness on metals & alloys of all kinds.
• Brinell hardness is also checked on non-ferrous materials like Cast iron, Alluminium, etc.
• Automatic weight selection with automatic zero setting dial gauge.
• Rockwell test minor load is 10 kgf & major loads are 60, 100, 150 kgf. Brinell test for Model : MRB major load is 187.5 & for Model : MRB-250 are 187.5, 250 kgf.
• Rockwell hardness scales such as HRA, HRB, HRC, etc. Brinell hardness scale such as HB is obtained by using different types of indentors ( Diamond / Ball ).
• For Model : MRB, Test height x Throat is - 215 x 132 mm. For Model : MRB-250, Test height x Throat is - 295 x 148 mm.
• Motorized versions are also available.
• Machines strictly conforms to IS:1586- 2000 for Rockwell test, IS:2281, BS:240, ASTM-E-10 for Brinell test.

Deep Throat Brinell Hardness Testing Machines With Roller Conveyor

• The machine has a heavy, robust, C-type load frame & has been designed for production testing of heavy components for Brinell hardness value. This machine is suitable for foundries, engineering industry, forging plants, automobile industries, on production line.
• Load stages - 750 kgf and 3000 kgf.
• Since most of the operations are fast and automatic, the test speed is high with less operator fatigue.
• A roller conveyor type sliding heavy table (base) for taking impression.
• Computerized model is available .Computerized model has built in CCD and suitable advanced software. Hardness will be displayed on computer monitor automatically. Results printout can be taken.
• Accuracy conforming to IS:2281.

The importance of Brinell Hardness Testing need not be over emphasized. But the conventional machines have following limitations

• Heavy jobs cannot be accommodated because of smaller vertical height & throat.
• Capacity to take heavy jobs is also less.
• Difficulties in Loading & positioning of job for different test points.

To overcome these difficulties, a special machine has been designed and developed by us. Besides the machine operation is automatic thereby substantially reducing the cycle time. The push button operation is user friendly without causing any fatigue. The roller conveyor facilitates handling of heavier jobs.

Typical OperationPush the ON button, Push the job from line conveyor roller table. Adjust the position of job. Operate foot switch. The indentor will come down, take the reading and go up automatically. Move the job for next reading. Take as many impressions in this way.

This Machine is designed to reveal the cupping qualities of metal sheets and strips . It can be used for testing the adhesion, elasticity and porosity of coats of paints or varnish by way of comparison.The appearance of the material after fracture gives an indication of the grain structure of the material and also of its constitution to same extent.L.C. of micrometer device is 0.01mm

Bend & rebend testing machines( fbr-100 kn )

• to conduct testing of carbon steel bars upto 40 mm diameter for reinforcement of concrete.
• c- frame design & hydraulically operated.
• maximum load capacity provided is 100 kn.
• dia.of support rollers is 100mm & distance between support rollers is 400mm.
• different sizes of formers (tools) are available from diameter 6 to 400mm.
• suitable re-bending tools supplied which will be incorporated in the machine.
• hinged grilled safety doors at front is provided for safety.
• accuracy conforming to bs : 4449.

technical specifications

hinged grilled safety door at front is provided.

• maximum load capacity 10, 000 kgs.
• maximum downward speed of piston 300 mm / min.
• stroke of piston 250 mm.
• maximum operating pressure of hydraulic system 200 kg /cm sq.
• dia of support rollers 100 mm.
• distance between support rollers (adjustable) -- 400 mm.
• formers of following diameters provided along with machine dia. - 12, 16, 20, 24, 30, 32, 40, 50, 60, 80, 140, 175, 224, 280 mm
• suitable re-bending tools supplied which will be incorporated in the machine.
• the up down of piston is through hand operated dc valve.
• the piston speed during down stroke is adjustable through manual operation of flow control valve.

• Compression Testing Machines ( Model : FCT, FCT-E, FCT-EC )
• Suitable for testing a wide range of materials.
• Wide range of standard & special (Optional) Accessories such as - Load-Stabilizer, Attachments for Brinell test, etc. are available.
• Various Models - Maximum Capacity from 100 kN to 3000 kN.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.
• Analogue, Digital & Computerized versions are available.

Application

This Machine applies a torque on the specimen held in its chuck and measures the twist. The machine is useful for material manufacturers, Research Institutions, Testing Laboratories, Educational Institution etc. to test metals.

Models

FTT-100, 200, 500, 1000, 2000 Nm (Capacity ranging from 100 Nm to 2000 Nm)

Accuracy & Calibration

Every machine has the accuracy of 1% of the true torque and calibrated according to standards set by IS, BS, ASTM, etc.

Salient Features

• Suitable for Torsion and Twist test on various metal rods and flats.
• Torque measured by pendulum dynamometer system.
• Geared motor to apply torque to specimen through gear box.
• Set of jaws to accommodate different size and diameter of test specimens provided.
• Computerised torsion testing machine is also available.

• To conduct fracture toughness test as per ASTM-E-208.
• Energies are - 350, 400, 450, 550, 800, 1100, 1350, 1650 J.
• Drop weight is 136 kg & height of fall is 1237mm (max.) adjustable to get the desired energies. Striker tip radius is 25.4mm & hardness is 50HRC (min.)
• Striker lifting arrangement is moterised driven by electrical motor & speed of lifting is 1.2 mtr/min.(appx.).

Suitable for Charpy and Izod impact Tests on various materials.Rigid designs of machine frame and other parts assure minimum energy absorption during fracture which results in improved test accuracies.

• Variety of tests like Tension, Compression, Cross breaking / Bending, Shear, Linear Bonding / Gripping / Peeling strength of adhesives & tapes, etc. are conducted.
• Suitable for testing a wide range of materials like rubber, wood, plywood, plastic, rexins, ceramics, teflon, cardboard, latex, composites, ferrous metals, non-ferrous metals, etc. of various forms like round, flat, thread, wires, dumbells, fabric, belts, strips, ropes, etc.
• Wide range of Grips, Attachments & Special fixtures are available to suit variety of material and shapes.
• Continuous roll autographic "Load Vs Elongation" recorder.
• Elongation scale with least count 1 mm.
• Three measuring ranges for accurate testing.
• A number of straining speeds are available for proper selection.
• Machine with AC or DC drive motor is available.
• Various Models - Maximum Capacity from 200 N to 50 kN.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.
• Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.

• Vickers Cum Brinell Hardness Testing Machines ( Model : BV )
• Suitable for finding out Vickers / Brinell hardness of metals from soft to very hard.
• Push button control for load selection.
• A range of test loads for Vickers / Brinell - from 1 kg to 250 kg.
• Optical Magnifications - 35X, 70X & 140X available.
• A precision Diamond Indentor (136 pyramid) is used to make sharp indentations on the specimens / samples.
• Maximum Test height x Throat : 250 x 150 mm.
• Load accuracy well within 1% of nominal load value. Machine conforms to IS:1754.
• Computerized model is available .Computerized model has built in CCD and suitable advanced software. Hardness will be displayed on computer monitor automatically. Results printout can be taken.

Automatic Data capture, storage & graphic display.Recording, storage & retrieval of results & details.On line display of load & extension.Fully automatic, on screen calculations based on the delivered data.Out put to digital printer of test data, test results & graphs.Auto detection of over load, over travel & specimen break, on detection of the above conditions, the machine is automatically switched off.Load resolution - 0.01% of machine capacity for entire range.Accurate and Users friendly software & all other facilities mentioned under Model : TUN.

• Variety of tests like Tension, Compression, Tranverse, etc. are conducted.
• Continuous roll autographic "Load Vs Elongation" recorder.
• Suitable for testing a wide range of metallic materials.
• Extra (Optional) Accessories such as - Mechanical Extensometer, Load-Stabilizer, Attachments for Brinell test, Tensile test for shouldered & threaded, Single & Double shear test, Bolts-Nuts & Washer test, Rope test, Flat Belt test, Bend-Rebend test, 180 Bend test, Pull-Out test, etc. are available.
• Capacities from 100 kN to 2000 kN.
• Various Analogue Models - TUN-100, TUN-200, TUN-400, TUN-600, TUN-1000 & TUN-2000.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.

• This is a combined hardness testing machine used to measure hardness of metals & alloys of all kinds, hard or soft, whether round, flat or irregular in shapes.
• This machine is ideally suitable for laboratories, tool rooms, Heat treatment shops, R&D departments, inspection departments, casting & forging industries, educational institutions.
• Rockwell & Brinell method is used for checking hardness on metals & alloys of all kinds.
• Brinell hardness is also checked on non-ferrous materials like Cast iron, Alluminium, etc.
• Automatic weight selection with automatic zero setting dial gauge.
• Rockwell test minor load is 10 kgf & major loads are 60, 100, 150 kgf. Brinell test for Model : MRB major load is 187.5 & for Model : MRB-250 are 187.5, 250 kgf.
• Rockwell hardness scales such as HRA, HRB, HRC, etc. Brinell hardness scale such as HB is obtained by using different types of indentors ( Diamond / Ball ).
• For Model : MRB, Test height x Throat is - 215 x 132 mm. For Model : MRB-250, Test height x Throat is - 295 x 148 mm.
• Motorized versions are also available.
• Machines strictly conforms to IS:1586- 2000 for Rockwell test, IS:2281, BS:240, ASTM-E-10 for Brinell test.

Deep Throat Brinell Hardness Testing Machines With Roller Conveyor

• The machine has a heavy, robust, C-type load frame & has been designed for production testing of heavy components for Brinell hardness value. This machine is suitable for foundries, engineering industry, forging plants, automobile industries, on production line.
• Load stages - 750 kgf and 3000 kgf.
• Since most of the operations are fast and automatic, the test speed is high with less operator fatigue.
• A roller conveyor type sliding heavy table (base) for taking impression.
• Computerized model is available .Computerized model has built in CCD and suitable advanced software. Hardness will be displayed on computer monitor automatically. Results printout can be taken.
• Accuracy conforming to IS:2281.

The importance of Brinell Hardness Testing need not be over emphasized. But the conventional machines have following limitations

• Heavy jobs cannot be accommodated because of smaller vertical height & throat.
• Capacity to take heavy jobs is also less.
• Difficulties in Loading & positioning of job for different test points.

To overcome these difficulties, a special machine has been designed and developed by us. Besides the machine operation is automatic thereby substantially reducing the cycle time. The push button operation is user friendly without causing any fatigue. The roller conveyor facilitates handling of heavier jobs.

Typical OperationPush the ON button, Push the job from line conveyor roller table. Adjust the position of job. Operate foot switch. The indentor will come down, take the reading and go up automatically. Move the job for next reading. Take as many impressions in this way.

This Machine is designed to reveal the cupping qualities of metal sheets and strips . It can be used for testing the adhesion, elasticity and porosity of coats of paints or varnish by way of comparison.The appearance of the material after fracture gives an indication of the grain structure of the material and also of its constitution to same extent.L.C. of micrometer device is 0.01mm

Bend & rebend testing machines( fbr-100 kn )

• to conduct testing of carbon steel bars upto 40 mm diameter for reinforcement of concrete.
• c- frame design & hydraulically operated.
• maximum load capacity provided is 100 kn.
• dia.of support rollers is 100mm & distance between support rollers is 400mm.
• different sizes of formers (tools) are available from diameter 6 to 400mm.
• suitable re-bending tools supplied which will be incorporated in the machine.
• hinged grilled safety doors at front is provided for safety.
• accuracy conforming to bs : 4449.

technical specifications

hinged grilled safety door at front is provided.

• maximum load capacity 10, 000 kgs.
• maximum downward speed of piston 300 mm / min.
• stroke of piston 250 mm.
• maximum operating pressure of hydraulic system 200 kg /cm sq.
• dia of support rollers 100 mm.
• distance between support rollers (adjustable) -- 400 mm.
• formers of following diameters provided along with machine dia. - 12, 16, 20, 24, 30, 32, 40, 50, 60, 80, 140, 175, 224, 280 mm
• suitable re-bending tools supplied which will be incorporated in the machine.
• the up down of piston is through hand operated dc valve.
• the piston speed during down stroke is adjustable through manual operation of flow control valve.

• Compression Testing Machines ( Model : FCT, FCT-E, FCT-EC )
• Suitable for testing a wide range of materials.
• Wide range of standard & special (Optional) Accessories such as - Load-Stabilizer, Attachments for Brinell test, etc. are available.
• Various Models - Maximum Capacity from 100 kN to 3000 kN.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.
• Analogue, Digital & Computerized versions are available.

Application

This Machine applies a torque on the specimen held in its chuck and measures the twist. The machine is useful for material manufacturers, Research Institutions, Testing Laboratories, Educational Institution etc. to test metals.

Models

FTT-100, 200, 500, 1000, 2000 Nm (Capacity ranging from 100 Nm to 2000 Nm)

Accuracy & Calibration

Every machine has the accuracy of 1% of the true torque and calibrated according to standards set by IS, BS, ASTM, etc.

Salient Features

• Suitable for Torsion and Twist test on various metal rods and flats.
• Torque measured by pendulum dynamometer system.
• Geared motor to apply torque to specimen through gear box.
• Set of jaws to accommodate different size and diameter of test specimens provided.
• Computerised torsion testing machine is also available.

• To conduct fracture toughness test as per ASTM-E-208.
• Energies are - 350, 400, 450, 550, 800, 1100, 1350, 1650 J.
• Drop weight is 136 kg & height of fall is 1237mm (max.) adjustable to get the desired energies. Striker tip radius is 25.4mm & hardness is 50HRC (min.)
• Striker lifting arrangement is moterised driven by electrical motor & speed of lifting is 1.2 mtr/min.(appx.).