Labline

Marine Lines, Mumbai, Maharashtra

UNIQUE FEATURES Ergonomic Design Easy to use DESCRIPTION Autoclave Portable is Single Walled. Made of Stainless Steel 304 Q Heavy Gauge The Gasket is made of Superior quality Silicon rubber which is easily Replaceable. Electrically operated supplied with pressure gauge, safety valve cum steam release valve.

UNIQUE FEATURES Ergonomic Design Easy to use Superior Functionality DESCRIPTION Double walled construction fully made of Stainless Steel 304 Q. Electrically operated Supplied with Two Safety Valves, Pressure gauge, Steam Release Valve, Drain Valve at bottom. Fitted with Jointless Silicon Rubber Gasket. Foot lifting arrangement to open lid. I.S.I approved heating elements.

Vertical autoclave, also known as steam sterilizers and top loading sterilizers, is a sterilizing machine that comes in a cylindrical shape. These machines help in sterilization of medical equipment, surgical instruments to name a few. This machines help in sterilization in Lab, Hospitals and Industry. TECHNICAL DATA Working pressure upto 15 PSI Power Supply: 230 Volts Chamber Size A.C. 50 Hz Single Phase OPTIONAL ACCESSORIES Digital Temperature controller cum indicator with timer. Low water level cut off Pressure cut off Switch Basket Stainless Steel

Hot plates are used in a laboratory as a heat source that can uniformly heat solutions and materials. They are considered much safer than traditional Bunsen burners because there is no open flame involved, just a heated plate. DESCRIPTION Heating element made from high grade I.S.I. Nichrome wire. Maximum Surface Temperature: 350C Temperature Controlled by Regulator OR Thermostat. Power Supply-230 Volts A.C. 50 Hz Single phase.

CONSTRUCTION Completely made of Stainless Steel. DESCRIPTION Heating element made from high grade I.S.I. Nichrome wire. Maximum Surface Temperature: 350C Temperature Controlled by Regulator OR Thermostat. Power Supply-230 Volts A.C. 50 Hz Single phase.

UNIQUE FEATURES Ergonomic Design Easy to replace the nets SPECIFICATIONS Body of the Heating Mantle is made of spun joint-less Aluminium. Heating element knitted fiber glass netting properly insulated. Long lasting element made by nichrome wire. Maximum surface Temp. 350C. Temp. The Temperature is Controlled by energy regulator. The Net is covered with Non breaking nichrome connection having porcelain beeds. Easy to replace the nets.

SPECIFICATIONS Fully made of Stainless Steel Operating frequency 30 KHz + 3 KHz Micro controller based Digital timer range 0 to 15 minutes. Heater-Thermostatically Controlled.

Lab incubators are essential equipment in the laboratory that provides a temperature-controlled environment to support growth of microbiological cultures. Other applications include coliform determination, egg incubation, heated storage, food and beverage testing, and pharmaceutical testing. CONSTRUCTION Double walled construction, Inner chamber made of Mild Steel/ Stainless Steel 304 Q & exterior made of G.I. Sheets powder coated. Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. Inner door made of Acrylic to see through the chamber & external metal door is fully insulated with S. S. lock, hinges. Air Ventilation is provided on the top of unit to remove hot gases/ fumes. Supplied with galvanized wire mesh shelves. TECHNICAL DATA Temp. Range: 5C above ambient to 60C Temp. Accuracy: With Thermostat: 2C or Digital: +0.5C Temp. Control : Temperature Controlled by Thermostat Digital Temp. : Micro-processor based Auto Tune P.I.D Digital Temperature Controller with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the other for Set Value of Tempreture (SV) Power Supply : 230 Volts A.C 50 Hz Single phase

Lab incubators are essential equipment in the laboratory that provides a temperature-controlled environment to support growth of microbiological cultures. Other applications include coliform determination, egg incubation, heated storage, food and beverage testing, and pharmaceutical testing. CONSTRUCTION Triple walled construction inner chamber made of Mild Steel/ Stainless Steel 304 Q & exterior made of G.I Sheets powder coated. Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. Inner door made of acrylic to see through the chamber & external metal door is fully insulated with S.S lock, hinges. Air Ventilations are placed at left & right side for hot gases/fumes. Supplied with galvanized wire mesh shelves. HEATING ELEMENT Heating element of Memmert model are placed at the right & left side of the inner chamber and is made of special grade chrome plated Nichrome wire (ISI Approved) for uniform temperature

Lab incubators are essential equipment in the laboratory that provides a temperature-controlled environment to support growth of microbiological cultures. Other applications include coliform determination, egg incubation, heated storage, food and beverage testing, and pharmaceutical testing. CONSTRUCTION Triple walled construction, Completely made of Stainless Steel Inner made of 316 Q & Outer made of 304 Q. Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. The door is fully insulated with S.S locks hinges. Air Ventilations are placed at left & right side for hot gases/fumes. Inner door made of acrylic to see through the chamber. Supplied with Stainless Steel wire mesh shelves. Forced Air Circulating System with Fan for Temperature Uniformity. Safety Thermostat. HEATING ELEMENT Heating element of GMP model are placed at the right & left side of the inner chamber and is made of special grade chrome plated Nichrome wire (ISI Approved) for uniform temperature. TECHNICAL DATA Temp. Range : 5C above ambient to 60C Accuracy : 0.5C Digital Temp. Controller : Micro-processor based Auto Tune P.I.D Digital Temperature Controller with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the another for Set Value of Tempreture (SV) Power Supply : 230 Volts A.C 50 Hz Single Phase

The Hot Air Oven Labtype is a precision instrument designed for sterilization, drying, and thermal testing in laboratory settings. It provides consistent, high-temperature performance, ensuring reliable results for various scientific and industrial applications. HEATING ELEMENT Heating is by specially designed heaters made of special grade chrome plated Nichrome wire (ISI Approved) which is fitted at the bottom of the oven. TECHNICAL DATA Temp. Range : 50C to 250C Accuracy : 2C Temp. Control : Temperature Controlled by Thermostat

UNIQUE FEATURES Ergonomic Design Easy to use High Temperature Accuracy Better Uniformity CONSTRUCTION Double walled construction inner chamber made of Mild Steel/ Stainless Steel 304 Q & exterior made of G.I Sheets powder coated. The gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. The door is fully insulated with S.S lock, hinges. Air Ventilations is provided on the top of unit to remove hot gases/fumes. Supplied with galvanized wire mesh shelves

UNIQUE FEATURES Ergonomic Design Easy to use High Temperature Accuracy Better Uniformity CONSTRUCTION Triple walled construction, inner chamber made of Mild Steel / Stainless Steel 304 Q & exterior made of G.I Sheets powder coated. Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. The door is fully insulated with S.S lock, hinges. Air Ventilation are placed at left & right side for hot gases / fumes. Supplied with galvanized wire mesh shelves

The Lab Oven GMP is a high-quality laboratory oven designed to meet Good Manufacturing Practice (GMP) standards. It offers precise temperature control and uniform heating, ensuring consistent and reliable results for pharmaceutical and biotech applications. CONSTRUCTION Triple walled construction, Completely made of Stainless Steel Inner made of 316 Q & Outer made of 304 Q. Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. The door is fully insulated with S.S lock, hinges. Air Ventilation are placed at left & right side for hot gases / fumes. Supplied with Stainless Steel wire mesh shelves. Forced Air Circulating System with Fan for Temperature Uniformity. Safety Thermostat. HEATING ELEMENT Heating element of GMP model are placed at the right & left side of the inner chamber and is made of special grade chrome plated Nichrome wire (ISI Approved) for uniform temperature

The Vacuum Oven is a specialized laboratory oven designed for drying heat-sensitive materials under reduced pressure. It provides precise temperature control and uniform heating, making it ideal for applications requiring gentle drying and minimal thermal degradation. CONSTRUCTION Double walled construction, Inner Chamber is made of thick gauge Stainless Steel 304 Q and Exterior chamber made of mild steel sheet pre greased, pretreated for rust proofing and powder coated. Gap between the chambers is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. Uniform drying under Vacuum. Supplied with Stainless steel tray, vacuum gauge, vacuum cock, toughened glass window in centre of the door to see through the chamber. HEATING ELEMENT Heating element is made from best quality Nichrome wire wounded around the chamber & covered with blankets. TECHNICAL DATA Temp. Range : 50C to 200C Accuracy : 2C Digital Temp. Controller : Micro-processor based Auto Tune P.I.D Digital Temperature Controller with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the another for Set Value of Tempreture (SV) Power Supply : 230 Volts A.C 50 Hz Single Phase

UNIQUE FEATURES Ergonomic Design Superior Functionality Negligible Maintenance High Temperature Accuracy Better Temperature Uniformity APPLICATIONS Biological Oxygen Demand Determination General Incubation Serum studies Enzyme Assays test Microbiology Lab

The Muffle Furnace is a high-temperature laboratory furnace used for ashing, heat treatment, and material testing. It features a robust design and precise temperature control, making it ideal for applications requiring uniform and controlled heating up to extreme temperatures. CONSTRUCTION Muffle Furnace Horizontal rectangular Outer body made of thick gauge Mild Steel with powder coating. Ceramic fibre wool insulation to prevent heat loss. Uniform heat distribution through all four sides with Kanthal A1 element. A special solid state silver fuse for protection of element in case of over-heating. TECHNICAL DATA Temp. Range : Maximum Temperature 1150C & Working Temperature 1100C Digital Temp. Controller : Micro-processor with dual display to view set temperature and current temperature with K type sensor and 1C Resolution Power Supply : 230 Volts A.C 50 Hz Single Phase

The Water Bath Rectangular is a versatile laboratory instrument designed for precise temperature control in heating and incubating samples. Its rectangular shape allows for efficient use of space and uniform heat distribution, making it ideal for various scientific and industrial applications. CONSTRUCTION Double walled Construction, Inner made of Stainless Steel 304 Q mirror finished & Exterior made of Stainless Steel Matt finish / Mild Steel powder coated Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. Diameter of holes 3 " with Concentric Rings & I.S.I Mark Heating Element. TECHNICAL DATA Temp. Range : 5C above ambient to 99C Accuracy : 1C Temp. Control : Temperature Controlled by Thermostat OR Digital Temp. Controller : Micro-processor based Auto Tune P.I.D Digital Temperature Controller with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the other for Set Value of Tempreture (SV) Power Supply : 230 Volts A.C 50 Hz Single Phase

The Water Bath Serological is designed for maintaining precise temperatures during serological and biological testing. It offers uniform heating and stability, ensuring reliable results for a range of diagnostic and research applications. CONSTRUCTION Double walled Construction, Inner made of Stainless Steel 304 Q mirror finished & Exterior made of Stainless Steel Matt finish / Mild Steel powder coated Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. I.S.I Mark Heating Element. TECHNICAL DATA Temp. Range : 5C above ambient to 60C Accuracy : 2C Temp. Control : Temperature Controlled by Thermostat OR Digital Temp. Controller : Micro-processor based Auto Tune P.I.D Digital Temperature Controller with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the other for Set Value of Tempreture (SV)

The Water Bath Round is a compact and efficient laboratory device designed for even heating and incubation of samples. Its round shape allows for optimal circulation and consistent temperature control, making it ideal for various scientific and industrial applications. CONSTRUCTION Double walled Construction, Inner made of Stainless Steel 304 Q mirror finished & Exterior made of Stainless Steel Matt finish / Mild Steel powder coated Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. Heating is by immersion heaters. TECHNICAL DATA Temp. Range : 5C above ambient to 99C Accuracy : 2C Temp. Control : Temperature Controlled by Thermostat OR Digital Temp. Controller : Micro-processor based Auto Tune P.I.D Digital Temperature Controller with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the other for Set Value of Tempreture (SV)

The Viscosity Bath is a specialized laboratory instrument used to measure and control the temperature of fluids for precise viscosity testing. It ensures accurate and consistent temperature conditions, facilitating reliable viscosity measurements for various research and quality control applications. DESCRIPTION Double walled Construction, Inner made of Stainless Steel & exterior made of G.I Sheets powder coated. Gap between the two walls is filled with glass wool insulation. A motor with stirrer for better temperature uniformity. Toughened glass window on both sides. Temperature Range : 5C above ambient to 99C. Accuracy : 0.5C with digital temperature controller. Power Supply : 230 Volts A.C 50 Hz Single Phase

The Constant Temperature Water Bath provides stable and precise temperature control for a range of laboratory applications. It ensures uniform heating, making it ideal for tasks requiring consistent temperature conditions, such as sample incubation and chemical reactions. DESCRIPTION Double walled Construction, Inner made of Stainless Steel & exterior made of G.I Sheets powder coated / Stainless Steel . Gap between the two walls is filled with glass wool insulation. Heating is by immersion type heaters. Digital Temp. Controller : Micro-processor based Auto Tune P.I.D Digital Controller Temperature with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the another for Set Value of Temperature (SV) A circulation pump with motor is mounted on a base and fitted on the side of the bath for uniformity of temperature. Temperature Range : 5C above ambient to 99C. Accuracy : 0.5C. Power Supply : 230 Volts A.C 50 Hz Single Phase

UNIQUE FEATURES Ergonomic Design Easy to use DESCRIPTION Complete unit made of Stainless Steel, Designed to provide Pyrogen free distilled water. Condensor can be opened easily for periodic cleaning. Easy Wall mounting. Heating elements are I.S.I Marked & are easily replaceable. The lid perfectly rests and get sealed inside the collar on head of tank which avoids loss of steam & jumping of lid. Constant water level arrangement. Power Supply: 230 Volts A.C 50 Hz Single Phase

Completely made of Stainless Steel. DESCRIPTION Heating element made from high grade I.S.I. Nichrome wire. Maximum Surface Temperature: 350C Temperature Controlled by Regulator OR Thermostat. Power Supply-230 Volts A.C. 50 Hz Single phase.

UNIQUE FEATURES Sturdy Design Easy to use DESCRIPTION U.V. Cabinet with long wave (365 nm), short wave (254 nm) & day light. U.V. Cabinet with long wave (365 nm), short wave (254 nm), day light and filter An enclosed viewing space which eliminates external light interference. Control switches mounted on top of the unit. It is supplied with 3 tubes to work on 230 volts A.C. Only

SALIENT FEATURES No Lubrication required Noiseless Performance Absolutely Portable Totally oil-free construction Negligible Maintenance All parts made from special graded Aluminium die cast material for light weight and good strength Diaphragms are made of special 2-Ply Nylon reinforced neophrene rubber Valves made of Stainless Steel 316Q Built in micro-suction filter Extra large bearings for trouble free and smooth running Standard Voltage Conditions-230 Volts A.C 50 Hz Single Phase

The Hand Refractometer, or Portable Refractometer, is a compact, handheld device used for measuring the refractive index of liquids. It provides quick and accurate readings, making it ideal for fieldwork and on-the-go analysis in various scientific and industrial applications.

DESCRIPTION Provides quick, convenient & accurate means of determination of refractive indices. Measurable range from 1.300 to 1.700 Accuracy 0.001 by direct reading and 0.0001 by estimation. Only a drop or two of the sample is sufficient for analysis. Sugar percentage range 0-95% with an accuracy of 1% on scale and 0.1% by estimation

This instrument is used for measuring - Percentage of Sugar, Fats in Oil & B.R. value in milk. It has two scales: One is Oil Scale (Butyroo Scale) having range of 0 to 100 with an accuracy 0.1 direct reading on micrometer. The other is Sugar Scale having a range of 50-80% with an accuracy of 1% reading directly on scale.

The Digital Refractometer Portable provides precise and user-friendly measurement of the refractive index and concentration of liquids. Its compact, portable design allows for quick and accurate analysis in diverse field and laboratory settings. The digital refractometer eliminates the uncertainity associated with mechanical refractometers and is easily portable for measurements in the field. The measurement technique and temperature compensation employ methodology recommended in the ICUMSA Methods Book (Internationally recognized body for Sugar Analysis). Temperature (in C or F) is displayed simultaneously with the measurement on the large dual level display along with icons for Low Power and other helpful message codes. KEY FEATURES INCLUDE: Dual-level LCD Easy setup and storage Battery operation with Low Power indicator (BEPS) Automatically turns off after 3 minutes of non-use.

The Polarimeter is a sophisticated instrument used to measure the optical rotation of polarized light as it passes through a sample. It is essential for determining the concentration and purity of optically active substances in various scientific and industrial applications. Note: We are Manufacturers, Suppliers, Exporters and Dealers of Various Polarimeter in Mumbai, Hyderabad, Bangalore, Pune, Ahmedabad, Chennai, Visakhapatnam, Surat, Nashik, Warangal, Vijayawada, Coimbatore, Vadodara, Navi Mumbai, Thane, Maharashtra, Goa, Gujarat, etc

SALIENT FEATURES Automatic Polarimeter instrument used to measure specific optical rotation of optically active substance. Measuring optical rotation and sugar degree. Storage of three times results. Built in auto controlling system with servomechanism Calculation of average values. Automatic Measurement Measurement of dark colored sample. RS232 Interface

APPLICATIONS Testing Soils and Agriculture Soils, Biomass Products, Coal, Pharmaceuticals Raw materials, Agro Industries, Wheat Atta, Suji, Maize Flour, Animal Feed, Bagasse, Dry Fruits, etc. DESCRIPTION A High performance compact, dependable Moisture Balance Infra Red for measurement of moisture content of materials. The 250 W infrared lamp gives great generation of heat which is controlled by auto-transformer. The balance is calibrated in terms of moisture percentage 0 - 100 % and is read directly on mechanical scale

SALIENT FEATURES Halogen Light Heating Curve (Graph) Temperature and time can be set The percentage of Moisture content The percentage of dry residual Touch Screen Store historical setting Loadcell Sensor

SALIENT FEATURES Halogen Light Heating Curve (Graph) Temperature and time can be set The percentage of Moisture content The percentage of dry residual Touch Screen Store historical setting Loadcell Sensor The Digital Moisture Analyzer delivers precise and quick measurements of moisture content using digital technology. Its advanced features ensure accurate results and efficient analysis, making it suitable for quality control in various industries such as food, pharmaceuticals, and materials.

The Stability Chamber is designed to simulate and control environmental conditions such as temperature and humidity to assess the stability of products over time. It is essential for testing the shelf life and performance of pharmaceuticals, chemicals, and other products under controlled conditions. TECHNICAL DATA For conditions as per ICH guidelines (International Conference of Harmonization) 25C -60% RH/40C -75% RH/30C -65% RH/ 25C-40% RH/40C -25% RH/30C-35% RH. Temperature Range: 10.0C to 60.0C Accuracy/Uniformity: 0.1C/+1C Humidity Range: 25% to 95% RH Accuracy/Uniformity: 2% RH / 3% RH Temperature/Humidity display: Digital LED 3.5 digit. Control: Microprocessor based PID control Auto tune. Resolution: 0.1C/1% RH Temperature sensor: PT-100 RH sensor: Direct capacitance type Heating: 'U ' shaped tubular heater in stainless steel. Cooling: CFC free Copeland make compressor utilizing R 134A eco friendly refrigerant, with condenser, motor and relay or as per the requirement of customer for higher accuracy

The Environmental Chamber provides precise control over temperature, humidity, and other environmental factors to simulate real-world conditions. It is crucial for testing the durability, performance, and reliability of products and materials in various industries. TECHNICAL DATA For conditions as per ICH guidelines (International Conference of Harmonization) 25C -60% RH/40C -75% RH/30C -65% RH/ 25C-40% RH/40C -25% RH/30C-35% RH. Temperature Range: 10.0C to 60.0C Accuracy/Uniformity: 0.1C/+1C Humidity Range: 25% to 95% RH Accuracy/Uniformity: 2% RH / 3% RH Temperature/Humidity display: Digital LED 3.5 digit. Control: Microprocessor based PID control Auto tune. Resolution: 0.1C/1% RH Temperature sensor: PT-100 RH sensor: Direct capacitance type

The Humidity Chamber is designed to provide precise temperature and humidity regulation for accurate and consistent testing. It is ideal for applications requiring controlled environmental conditions, such as material testing, stability studies, and product development. TECHNICAL DATA For conditions as per ICH guidelines (International Conference of Harmonization) 25C -60% RH/40C -75% RH/30C -65% RH/ 25C-40% RH/40C -25% RH/30C-35% RH. Temperature Range: 10.0C to 60.0C Accuracy/Uniformity: 0.1C/+1C Humidity Range: 25% to 95% RH Accuracy/Uniformity: 2% RH / 3% RH Temperature/Humidity display: Digital LED 3.5 digit. Control: Microprocessor based PID control Auto tune. Resolution: 0.1C/1% RH Temperature sensor: PT-100 RH sensor: Direct capacitance type Heating: 'U ' shaped tubular heater in stainless stee

The Laminar Air Flow Horizontal provides a clean and controlled environment by directing filtered air horizontally across the workspace. It is essential for protecting sensitive samples and maintaining a contamination-free area in laboratories and manufacturing settings. DESCRIPTION Designed so as to meet the requirements of US Federal Standard 209 B (BS 5295) providing particle free air to meet (class 100 conditions). The cabinets are used in Tissue Culture and Microbiological application. Constructed with M.S Powder coated. Or Constructed with Stainless Steel GMP Model. Unit designed to provide a Laminar Flow Work space comprising as standard feature HEPA filter Efficiency > 99.97% at 0.3 microns (Factory DOP tested). Pre - filter 95% efficient @ 5 microns, suitable motor blowing assembly. Working Table Top of Stainless Steel; Stain Finish, Side Acrylic Panels; Fluorescent Tube Light; U.V Light, Pressure Differential Manometer, Gas Cock duly fitted and complete with front door. Unit mounted on Castor wheels for easy movability

The Laminar Air Flow Vertical offers a sterile work environment by directing filtered air vertically from the top of the unit downwards. It ensures a contamination-free workspace, making it ideal for sensitive operations in laboratories and cleanroom settings. DESCRIPTION Designed so as to meet the requirements of US Federal Standard 209 B (BS 5295) providing particle free air to meet (class 100 conditions). The cabinets are used in Tissue Culture and Microbiological application. Constructed with M.S Powder coated. Or Constructed with Stainless Steel GMP Model. Unit designed to provide a Laminar Flow Work space comprising as standard feature HEPA filter Efficiency > 99.97% at 0.3 microns (Factory DOP tested). Pre - filter 95% efficient @ 5 microns, suitable motor blowing assembly. Working Table Top of Stainless Steel; Stain Finish, Side Acrylic Panels; Fluorescent Tube Light; U.V Light, Pressure Differential Manometer, Gas Cock duly fitted and complete with front door. Unit mounted on Castor wheels for easy movability

The Biosafety Cabinet provides a controlled environment with filtered air to protect both the user and the sample from contamination. It is essential for safely handling hazardous materials and conducting sensitive biological experiments in research and clinical laboratories. APPLICATIONS Application includes isolation and identification of plant / human pathogens, work in virology, tissue culture, sterility testing and recombinant DNA research. This Biohazard Cabinet offers operator protection from low to moderate risk biological agents (or Chemical carcinogens), while providing a sterile work environment for the procedure. The cabinet is kept under negative pressure with partial quantity of recirculated air exhausted through a HEPA filter. The Additional main features are as under :- Specially suited for wet processing, water fab, chemical work, critical biological work involving virus and pathogens & for microbiology, biochemistry etc. CONSTRUCTION Biosafety complete construction made of mild steel powder coated with perforated stainless steel table top. OR Biosafety complete construction made of stainless steel Quality 304/316 with perforated table top. Integral powerful exhaust system, Built in positive Air Curtain effect to prevent inside air from going out and room from entering in, providing total process and operator safety. Exhaust ducting to carry the air outside. Front sliding door, U.V. light, Manometer, Gas cock etc. as Standard accessories

The Biosafety Cabinet GMP is designed to meet Good Manufacturing Practice (GMP) standards, offering enhanced safety and contamination control for handling critical materials. It ensures a sterile work environment while protecting both the operator and the product, making it ideal for pharmaceutical and biotech applications. APPLICATIONS Application includes isolation and identification of plant / human pathogens, work in virology, tissue culture, sterility testing and recombinant DNA research. This Biohazard Cabinet offers operator protection from low to moderate risk biological agents (or Chemical carcinogens), while providing a sterile work environment for the procedure. The cabinet is kept under negative pressure with partial quantity of recirculated air exhausted through a HEPA filter. The Additional main features are as under :- Specially suited for wet processing, water fab, chemical work, critical biological work involving virus and pathogens & for microbiology, biochemistry etc. CONSTRUCTION Biosafety complete construction made of mild steel powder coated with perforated stainless steel table top. OR Biosafety complete construction made of stainless steel Quality 304/316 with perforated table top. Integral powerful exhaust system, Built in positive Air Curtain effect to prevent inside air from going out and room from entering in, providing total process and operator safety. Exhaust ducting to carry the air outside. Front sliding door, U.V. light, Manometer, Gas cock etc. as Standard accessories

UNIQUE FEATURES Ergonomic Design Easy to use CONSTRUCTION Double walled construction inner chamber made of Mild Steel/ Stainless Steel 304 Q & exterior made of G.I Sheets powder coated. Gap between the walls is filled with special grade glass wool for proper insulation to avoid heat loss and thereby saving energy. The door is fully insulated with S.S lock, hinges. Air Ventilations is provided on the top of unit to remove hot gases/fumes. Supplied with galvanized wire mesh shelves

MODEL: LSC-365 * Complete S. S. Models are also Available Safety in the Laboratory is a primary concern. The fume hoods meet the challenge high degree of efficiency. A wide variety of models and comprehensive option packages have been designed to enable you to tailor your fume hood to a specification FUME HOOD MADE OF COMPLETE MILD STEEL: Are manufactured from best quality C.R.C.A. Sheets (Cold Rolled Case Annealed Low carbon steel sheets) of 18/20G which are duly epoxy polyester powder coated. Powder coating of this quality provides better protection from acid fumes in the lab

The Dry Bath Incubator offers precise temperature control without the use of water, making it ideal for heating samples in various tubes and plates. Its compact design and uniform heating make it a versatile tool for incubation, enzymatic reactions, and other temperature-sensitive processes. DESCRIPTION The body is made of M.S epoxy powder coated. Temperature range - ambient to 99C Accuracy 0.2C Digital Temp. Controller: Micro-processor based Auto Tune P.I.D Digital Controller Temperature with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the another for Set Value of Tempreture (SV) Aluminium Blocks -Supplied with 3 nos. interchangeable Aluminium blocks of 75 x 50 x 50 mm for accommodating 0.5 ml, 1.5 ml centrifuge tube, 12 mm, 16 mm or 19 mm Test tube (As per requirement)

The Heating Block provides reliable and consistent heating for sample tubes and vessels in a compact, controlled environment. It is ideal for applications requiring precise temperature regulation, such as enzymatic reactions and sample digestion in laboratory settings. DESCRIPTION The body is made of M.S epoxy powder coated. Temperature range - ambient to 99C Accuracy 0.2C Digital Temp. Controller: Micro-processor based Auto Tune P.I.D Digital Controller Temperature with PT 100 sensor & Resolution 0.1C. Dual display one for process value (PV) & the another for Set Value of Tempreture (SV) Aluminium Blocks -Supplied with 3 nos. interchangeable Aluminium blocks of 75 x 50 x 50 mm for accommodating 0.5 ml, 1.5 ml centrifuge tube, 12 mm, 16 mm or 19 mm Test tube (As per requirement). Note: We are Manufacturers, Suppliers, Exporters and Dealers of Various Dry Bath Incubator in Mumbai, Hyderabad, Bangalore, Pune, Ahmedabad, Chennai, Visakhapatnam, Surat, Nashik, Warangal, Vijayawada, Coimbatore, Vadodara, Navi Mumbai, Thane, Maharashtra, Goa, Gujarat, etc

For growing culture of micro organism and tissue cells. UNIQUE FEATURES The body is made of Heavy M.S powder coated with Stainless Steel tray for flask. The shaking speed 20 to 200 RPM Orbital strokes per minute and the orbit diameter of 25 mm. Supplied with S.S Clamp for conical flask. Available with Electronic Speed Controller, OR With Electronic Speed Controller & Digital RPM Meter

DESCRIPTION For growing culture of micro organism and tissue cells. The drive mechanism is powered by - a permanent magnet geared DC Motor with 25 mm diameter motion OR AC Frequency drive geared motor for continuous working. Transparent acrylic cover allows unobstructed view of the chamber contents from front two sides and from top. The body made of Heavy M.S and painted with epoxy powder paint. The inner walls of the incubator will be pasted with laminated sheet to avoid heat loss. Supplied with Lotus Clamps for conical flask

DESCRIPTION Suitable for COD method for monitoring wastewater influent and effluent, industrial process water, and more. Aluminium Heating block with holes is used to hold C.O.D tubes. (With tubes, condensers and stands)

MODEL: Digital Microscope Cameras Complete range of Digital Microphotography solutions cameras for converting any microscope to a digital microscope. Choose from a wide range of up to 20 Megapixels of high resolution cameras. Camera Types: CMOS Cameras, CCD Cameras Suitable Applications: Life Sciences, Genetics Pathology, Material Science, Metallography, Mineralogy and Geology, Quality Control, Forensics, Macroscopy. Software: Each Camera delivered with advance Image capturing and analysis software MicroView. C-mount Adapters for Zeiss, Nikon, Leica and Olympus Microscopes

Features of Pipette Fixed & Variable volume Easy Volume setting Two Step Plunger Operation Click stop system for volume setting High Accuracy Easy to calibrate Ergonomy light weight and soft plunger Autoclavable lower assembly.

TABLET DISINTEGRATION TEST APPARATUS is a Microprocessor based instrument designed for accurate determination of disintegration time of tables, capsules, as per IP/BP/USP standard. These tests are carried out by quality control and R & D departments in pharmaceutical industry. Two hotplates are provided to maintain the temp. of the liquid media (1000ml beaker). Two batches of six tablets each can be tested simultaneously. Solid state Heat Regulator is provided to control the heat of the Hotplate. A constant speed 30 RPM motor drive single bar up & down smoothly to lift two baskets. The stroke is adjusted as per the specifications. A simple & unique arrangement of loading & unloading the basket makes it user friendly.

APPLICATION: To study the packing down of powder beds of different pharmaceutical & chemical powders. FEATURES: Acrylic Measuring Cylinder Holder with Rubber cushioning. Maintenance free AC Motor 30 RPM. Direct Stroke setting eliminates the tedious calculation of Timer Mode. Microprocessor based counter with non contact sensor for trouble free operation. In power, failure, the non-volatile memory of the microprocessor remembers the last mode of operation

The Antibiotic Zone Reader determines the strength of antibiotic materials by measuring diameter of 0 to 80.0 mm of inhibited zone in petri dish. Agar in petri dish is inculated with bacteria. Then sensitivity disc is dispensed on to dish. After incubation, bacterial growth covers disc except circular inhibited zone. Zone diameter is the function of antibiotic strength. Light from the base passes up through transparent & semi-transparent portion of agar

Easy to handle the apparatus as less glass parts are used. Specially designed continuous duty positive displacement peristaltic pump is used to dispense reagent and methanol into reaction vessel. Reversing facility available to transfer the reagent from the tubing back to reservoir. Digital readout to avoid human reading errors. Karl Fischer Titrator finds use in chemical, pharmaceutical, food, cosmetics, oil and many other industries in QC and R & D Laboratories

DIGITAL FLOCCULATOR (JAR TEST APPARATUS) has been specially designed for use in water treatment plants to correctly estimate the dosing of alum and such other coagulants for treatment of water & sewage. It provides identical test condition for all samples. sulphate concentration & for measuring suspended matter and colloids general.

The Digital Melting Point Apparatus accurately measures the melting point of substances with advanced digital controls and precise temperature readings. It provides reliable data for material characterization and quality control in pharmaceutical and chemical laboratories. FEATURES: Silicon oil Bath with Magnetic Stirrer Special 'H ' Type glass vessel and precise rate controller for temperature uniformity Pre Temp, Setting with alarm to reduce the active time requirement of the chemist SPECIFICATIONS: DISPLAY : DIGITAL RED LED DISPLAY TEMP. RANGE : UP TO 300C RESOLUTION : 0.1C RATE OF HEATING : 0.5, 1, 2 & 5C SELECTABLE AFTER REACHING PRESET TEMP. STIRRER : MAGNETIC WITH TEFLON COATED BIT VIEWING : THROUGH MAGNIFYING LENS, BACKGROUND ILLUMINATED BATH : 100 ML OIL BATH WITH LEVEL MARKING SENSOR : RTD (PT-100) TEMP. SENSOR

The Tablet Dissolution Test Apparatus assesses the dissolution rate of tablets in a liquid medium, simulating the digestive process. It is vital for ensuring consistent drug release and bioavailability, playing a key role in pharmaceutical quality control and regulatory compliance. FEATURES: As per usp Standards Microprocessor based digital temperature Controller Digital RPM Display Digital Timer Presentable from 1 Min to 99 Hrs. 59 Min. OR 99 Min. 59 Sec with alarm Provided with Round Bottom Glass Jar, Paddle and Basket SPECIFICATIONS: Temperature Range : ambient to 45C Speed : Variable from 25 to 160 RPM with accuracy of +/-1 RPM Other Options : SINGLE Test Model - Manual Lifting Arrangement

The Friability Test Apparatus is Microprocessor based instrument designed to monitor the resistance of tablets to stresses and to decide their suitability for the further process. These tests are carried out by quality control and R & D departments in pharmaceutical industry. A fix 25 RPM motor drives the unique universal acrylic drum (same drum can be used at the left or right side of the instrument). Digital microprocessor based counter is provided to pre-set the revolution & to automatically stop the motor with alarm. This feature eliminates the tedious calculation of timer mode. In power failure, the non-volatile memory of the microprocessor remembers the last mode of operation, and completes the test after the power supply is resumed.

The Test Sieve is a laboratory tool used for particle size analysis by separating materials based on their size. It is essential for quality control in various industries, ensuring consistency and uniformity in powders and granular materials.

KEY FEATURES Ergonomic & compact design for user convenience Anti-fungus treatment for component durability High eyepoint design eyepiece (F.N. 20) SMPS circuit for constant voltage output Rackless stage for durability and ease of use Component security - student proof Choice of halogen and LED illumination

KEY FEATURES Parfocal and Centered Optics Optics with Multi-layer Coating & Anti-Fungus treated Choice of Halogen and LED Illumination Easy Access for Lamp Replacement The Binocular Microscope (MLX-B Plus) offers enhanced optical performance with dual eyepieces for comfortable viewing. It is designed for detailed observation in biological, clinical, and educational settings, providing clear and accurate magnification.

KEY FEATURES Plan infinity corrected optics Multilayer coated optics Ergonomic sidentopf head FN.20 wide field eyepiece Inward facing quadruple revolving nosepiece Available in LED, halogen & battery back-up variants Anti-fungal optics Hard-coated stage with double slide holder Rackless stage - optiona

KEY FEATURES Where there is quality, so should there be economy. This philosophy was applied to every critical step in the design of the Lx 500. With its graceful symmetry and its highly ergonomic features, this microscope speaks to todays researchers who understand that affordability and reliability need not be mutually exclusive. The Lx 500 is the outcome of a combination of worldclass technology and design innovation. With its feature rich configuration and a host of accessories, the Lx 500 is a versatile and fully extendable research microscopy system. The Lx 500 is where economy meets first class. All contact surfaces are treated with antimicrobial agents to ensure zero point-of-contact bacterial contamination.

Revolving Nosepiece: Triple revolving nosepiece with accurate centering and positive click stops. Focusing System: Coarse motion by rack and pinion and fine motion by lever system. Stage: Fixed 110mm x 110mm square stage with stage clips and N.A. 1.25 iris diaphragm condenser. Illumination: Plano-concave 50mm adjustable reflecting mirror on gimble mount. Objective Lens: 10x and 45x (S/L) achromatic objectives. Eyepiece: 10x and 15x huygenian. Packing: Plywood carrying cabinet with lock and keys or in styrofoam case. Accessories: Vinyl dust cover, cleaning cloth and instruction manual.

Body: Monocular tube inclinable up to 90 Revolving Nosepiece: Triple revolving nosepiece with accurate centering and positive click stops. Focusing System: Coarse motion by rack and pinion and fine motion by lever system. Stage: Fixed 120mm x 120mm square stage with detachable graduated mechanical stage. Condenser: Sub stage Abbe type up & down moveable condenser N.A. 1.25 with iris diaphragm

KEY FEATURES Ergonomic & compact design for user convenience Anti-fungus treatment for component durability High eyepoint design eyepiece (F.N. 20) SMPS circuit for constant voltage output Rackless stage for durability and ease of use Component security - student proof Choice of halogen and LED illumination

The Magnus Microscope (MLX-B) Plus offers enhanced optical performance and a robust design for detailed examination. It features advanced optics and ergonomic design, making it suitable for various applications in biological, clinical, and educational laboratories.

KEY FEATURES Plan infinity corrected optics Multilayer coated optics Ergonomic Siedentop head FN.20 wide field eyepiece Inward facing quadruple revolving nosepiece Available in LED, halogen & battery back-up variants Anti-fungal optics Hard-coated stage with double slide holder Reckless stage - optional

KEY FEATURES Plan Infinity Optics with Field of view 22mm Parfocal and Centered Strain Free Optics Optics with Multi-layer Coating & Anti-Fungus treated Choice of Halogen, LED Illumination & Battery backup Easy Access for Lamp Replacement Siedentop Butterfly head. Hard coated Reckless stage Inward Quintuple Nosepiece Universal Power Supply Anti-Fungus Treatment Centrable Condenser

The Magnus Microscope (CH20i) is designed for reliable and versatile use in educational and laboratory settings. It offers clear optics and user-friendly features, making it ideal for detailed observation and analysis in various biological and clinical applications.

Teaching Microscope for 5 Persons Plan infinity corrected optics Multilayer coated optics FN.20 wide field eyepiece LED pointer attachment Ergonomic sidentopf BI and TR head Inward facing quadruple revolving nosepiece Available in 3W LED Hard-coated stage with double slide holder

The Labline Stereo Zoom Microscope provides high-resolution, three-dimensional imaging with adjustable zoom capabilities. It is ideal for detailed inspection and analysis of specimens in various fields, including electronics, biology, and material science, offering versatility and clarity for a range of applications. MECHANICAL BODY Track stand with fan type base. Lateral zoom control movement. Reflected & transmitted LED Illuminator. Incident & Transmitted light system with LED Lamp. The system regulated with transformer has separate intensity control knob. Clip for holding specimen, Base Size is 240mm x 280mm. Zooming range & ratio : 1:6:4 Zoom 0.7x to 4.5X with magnification Magnification Range 7X - 45X Working Distance : 100MM

The Olympus Stereo Zoom Microscopes, including models SZ61, SZ51, SZ51-60, SZ61-60, and SZ61TR, offer high-quality stereoscopic imaging with versatile zoom capabilities. These models are designed for detailed inspection and analysis, providing exceptional clarity and depth perception, making them ideal for applications in fields such as electronics, biology, and materials science. The compact design owes much to the incorporation of the Greenough optical system, which delivers excellent flatness and ample depth of field as well as clarity, detail, accurate color and the least possible distortion. Dependable, high-performance optics are central to the achievement of consistent, accurate results in today 's widening range of biological microscopy applications as are ergonomic features which make even long-duration tasks easier and less demanding to perform.

KEY FEATURES Features Simple Operation Dual Measurement Includes Temperature Display With All Readings 100 Point Memory Detachable Electrode Holder Compact Footprint Saves Valuable Bench Space Custom Setup Options Hold Function And Stability Indicator 3-Year Warranty

Digital pH Tester offered are made available with readout of 3 digit LED display in range comprising pH 0 to 14.00 and mV from 0 to 1.999. Further, these feature resolution of pH 0.01 & mV 1; accuracy of pH 0.02 pH 1 least count & mV 0.2% 1 least count. These are also made available with temperature compatibility from 0 to 100oC with operational power support required of 230 V AC 10% 50 Hz, 4 VA. With ABS body, these also feature accessories comprising Rod, Patch cord for Electronic buffer, Stand set, Electrode Clamp, Buffer tablets for 9.20, 7.00, 4.00 pH; Teflon magnet and others.

The Labline TDS Meter measures the total dissolved solids (TDS) in liquids, providing essential data on water quality and purity. It features a straightforward digital display and user-friendly controls, making it suitable for a range of applications in environmental testing, water treatment, and laboratory analysis.

Digital Conductivity Meter offered come with measurement unit comprising MHO and S in range of 01 to 200 m in six ranges including 200 m, 20 m, 2 m, 200 , 20 , 2 . Further, these feature accuracy of 1% last 2 digits and come in ABS body finish so as to provide for longer service life standards. With instant warming period, these deliver standard conductance of 1.000 m with stirrer speed of 200 RPM (fixed).

Ideal instrument to check blister Packs, Strips for Leak Test. The old method of separate desiccator and huge vacuum pump is replaced with the new Leak Test Apparatus in GMP Stainless Steel Body with phenomenal compactness. The instrument is equipped with Diaphragm type vacuum pump gives higher level of vacuum in shortest possible time. Die pressed polycarbonate vacuum desiccator sustains vacuum for long time. A vacuum gauge is provided to indicate vacuum level which is connected ti isolation valve to disconnect the source. Thus avoiding the need of continues running of vacuum pump. 99 minute Digital timer helps the operator to do other work It 's amazing compactness saves lot of valuable place in process laboratories.

The Labline Digital Viscometer measures the viscosity of liquids with high precision using advanced digital technology. It provides accurate and reproducible results for various applications, including quality control, research, and industrial processes, ensuring reliable viscosity measurements. DIGITAL DIRECT READING ROTATIONAL VISCOMETER Labline series is Rotational Digital Direct Reading Viscometer to measure absolute viscosity of Newton Liquids as well apparent viscosity of non-Newton liquid featured by high flexibility reliable Test result, easy operation and good appearance. COMMON SPECIFICATIONS Selected Speed Viscosity Reading Temperature DATA DISPLAYED Selected Spindle Torque Percentage

The Brookfield Digital Viscometer provides precise and reliable measurements of fluid viscosity using advanced digital technology. It offers detailed control and accurate data for a wide range of applications, including quality control and research in industries such as pharmaceuticals, chemicals, and food processing. FEATURES USER-FRIENDLY INTERFACE Keypad control Sharp viewing screen for Close up or distance viewing No Calculations Required Direct reading of viscosity DISPLAYED INFO: Viscosity (cP, P, mPas or Pas) % Torque Speed/Spindle Easy-to-Use RANGE Push for determining full scale range (FSR) viscosity BUBBLE LEVEL: Conveniently located for easy adjustment ACCURACY: 1.0% OF RANGE REPEATABILITY: 0.2% 18 Speeds For complete range capability

Microprocessor Visible Spectrophotometer offered features single beam, grating 1200 lines/mm optical system that comes with spectral bandwidth of 5 nm, wavelength range of 325 1000 nm and wavelength accuracy of + 2.0 nm. These advanced technology based spectrophotometers also feature wavelength reproducibility of 1 nm, photometric accuracy of + % T, photometric reproducibility of < 0.5 % T, Tungsten halogen lamp 6V/10Wbased light source and 4 LED digital display support. Offering stable & accurate functionality support, these deliver high VIS performance between 325 to 1000 nm and RS232C communication support

UV-Vis Spectrophotometer Model UV-1900i - SHIMADZU (Japan) Shimadzu 's UV-1900i provides the optimum balance of performance and usability, plus enhanced regulatory compliance functions, making it ideal for applications in a variety of industries. It features high resolution, low stray light, high reproducibility, and an ultra-fast scan function, while the easy-to-use interface simplifies operation and enables acquisition of results quickly and easily.

The UV3000 series of UV-Visible Spectrophotometers have been designed using state of the art technology. The instruments are professionally manufactured to a very high specication, with excellent quality control. The instruments have been designed using expertise gathered over many years in the eld of UV-Visible Spectrophotometry. This gives the UV3000 series of instruments high performance characteristics, exibility and user friendliness

"ML " series of Magnetic Stirrers with stainless steel top housing are most compact models. Permanent Magnet DC (PMDC) motor gives high torque even at lower speeds and maintains speed stability despite viscosity or volume changes. Different models available for all types of laboratory stirring applications up to 10 liters. Accurate stepless speed control with digital display allows smooth variation up to 1200 rpm.

The Digital Colony Counter provides accurate and efficient counting of microbial colonies on agar plates. It features a digital display and advanced counting algorithms, enhancing precision and reducing manual errors in microbiological analysis and quality control. FEATURE: Streamlined design enables fast and accurate count & reduces operator fatigue. Hold function to stop counting at any stage. 40 memory locations with data storage even after the power switch off. Four Digit resettable digital counter with audio beep at every count. Auto mark-Market pen probe, for counting and marking simultaneously. Wolffhuegal grid glass plate. Focusing adjustable. 110 mm Magnifying glass

Laboratory Centrifuges model R - 8C & R - 8C DX are suitable for routine sample analysis in Medical, Hospital, Pathology and Institutional laboratories. With a wide choice of rotor heads and adaptors, these units are truly versatile. Micro Centrifuges models RM - 12C / RM - 12CDX are ideal for growing routine application in biochemical and clinical labs, for Hematocrit, Corpuscle Percentage contents in blood, Serum analysis and precipitate separation etc

Clinical Centrifuge 4 Tube is designed for the efficient separation of biological samples using up to four tubes simultaneously. It features precise speed control and reliable operation, making it ideal for small-scale clinical and diagnostic applications where space and efficiency are crucial. Note: We are Manufacturers, Suppliers, Exporters and Dealers of Various Centrifuge in Mumbai, Hyderabad, Bangalore, Pune, Ahmedabad, Chennai, Visakhapatnam, Surat, Nashik, Warangal, Vijayawada, Coimbatore, Vadodara, Navi Mumbai, Thane, Maharashtra, Goa, Gujarat, etc

Doctor Centrifuge 8 Tube provides efficient separation of samples using up to eight tubes at once. It offers reliable performance with precise speed control, making it suitable for clinical and diagnostic applications that require handling multiple samples simultaneously. Note: We are Manufacturers, Suppliers, Exporters and Dealers of Various Centrifuge in Mumbai, Hyderabad, Bangalore, Pune, Ahmedabad, Chennai, Visakhapatnam, Surat, Nashik, Warangal, Vijayawada, Coimbatore, Vadodara, Navi Mumbai, Thane, Maharashtra, Goa, Gujarat, etc

THE BRILLIANT MONO-TECH Unique & Unequalled high-end MONO- TECH technology sensor based on electromagnetic force compensation to match the highest international standards. MAXIMUM REPEATABILITY AND ADHERENCE TO USP The best weighing accuracy and sd < 1d repeatability along with adherence to USP requirements (chapter 41 and 1251) set a new benchmark for mass measurement quality

The Precision Balance (CY 223) delivers accurate and consistent weight measurements with a high degree of precision. It is designed for various laboratory and industrial applications, providing reliable data for precise weighing tasks and quality control. OVERLOAD PROTECTION Capacity tracker built into display for easily monitoring possible overloads. LEVELING Balances have adjustable feet for maintaining / providing uniform level. EFFICIENT OPERATION The large LCD backlit display, push button keys easy access to the main functions make these balances easy to use. High-Quality construction and solid performance ensure consistent and precise weighing results. AMBIENT CONDITIONS MONITORING Balances have unique ambient conditions monitoring solution, applied to supervise environmental conditions at the balance workplace. PERFECT SELF AUTOMATIC CALIBRATION (PSAC) CY-C SERIES Temperature controlled automatic internal adjustment (PSAC) uses the built-in weights to ensure consistently accurate results. PRINT FORMAT Built-in function, you can add the date and time to your results in accordance with GMP /GLP/ISO documentation regulations. USP (United States Pharmacopeia) 21CFR Part 11 Compliance Available on Request

STANDARD FEATURES Rugged & reliable design Compact and space saving. Easy to read LED display (CG Series) Easy to read Backlight LCD display (CG-L Series) Built-in rechargeable battery. Piece counting function available. Draft Shield interior. (10mg / 1mg) Fast weighing response time. Large Stainless Steel Pan. Standard RS 232C Interface

Shimadzu Balance (TXB) provides precise and reliable weight measurements with advanced features and robust construction. It is designed for accurate weighing in laboratory and industrial settings, offering high performance and durability for a variety of applications. WINDOWSDIRECT COMMUNICATION FUNCTION ONLY A CABLE IS NEEDED TO SEND WEIGHING DATA TO A COMPUTER Send balance data to Excel or other Windows applications without any data communication software installation required. All you have to add is one RS-232C cable. By combining standard AutoPrint functions with typical spreadsheet functions, even difficult applications can be easily automated. If youd like to use WindowsDirect with Windows 7 Windows Vista, or USB port, please contact to our distributors

DURABLE, HIGH-PERFORMANCE ALUMINUM ALLOY MASS SENSOR UNIBLOC The ATX/ATY series incorporates a one-piece aluminum alloy mass sensor technology (UniBloc), first introduced by Shimadzu for precision balances in 1989. It excels in performance, and resists deterioration and damage by ordinary impacts. The UniBlocs compact, uniform structure replaces 70 parts found in a conventional electromagnetic balance sensor assembly and ensures stable temperature characteristics, excellent response time and stable corner-load performance. The UniBloc design permits a consistency of production that assures reliability and a long operational life