GST : 24AASCM8220F1ZE
5.0/5
Our Products
We offer the best product range of Slurry Pump Shaft Spacer, Slurry Pump Cover Plate, Slurry Pump Grease Retainer, Slurry Pump Labyrinth Locknut and Slurry Pump Back Liner.
Slurry pump shaft spacer is one of shaft seal parts in gland packing seal slurry pumps which fills a vacancy on the shaft between shaft sleeve and impeller. This is designed to increase interchangeability of shaft sleeve. Slurry pump shaft spacers are normally made in stainless steel, special materials are also available.
Slurry pump cover plate is suction side casing in lined slurry pumps which pull together with frame plate around the liners via cover plate bolts. Compared to unlined slurry pump, cover plate and frame plate act as pressure retaining devices located outside the slurry, the abrasive wear of liners has no effect on the maximum allowable working pressure.
Slurry pump grease retainer basic part number is 046, its function is to keep grease in bearings area. Slurry pump grease retainer are normally made in grey iron material, ductile iron and steel are also available.
Slurry pump labyrinth locknut basic part number is 061, its function is to fasten the labyrinth of drive end. Slurry pump labyrinth locknuts are normally made in carbon steel plating zinc.
Slurry pump end cover is one of drive end parts which is installed on both ends of bearing housing to fix the bearings. Slurry pump end cover are normally made in grey iron material, ductile iron and steel are also available.
Slurry pump labyrinth is a component of drive end parts, its purpose is to plug the hole in bearing housing where the shaft passes through. Slurry pump labyrinth are normally made in grey iron material, ductile iron is also available.
Slurry pump shaft is one of drive end parts which connect impeller to drive device. Slurry pump shafts are normally made in carbon steel, special material is also available.
Slurry pump shaft sleeve function is to protect the shaft from slurry abrasion and corrosion. A slip fit allows the shaft sleeve to be replaced quickly. Slurry pump shaft sleeves are normally made in stainless steel, ceramic coated sleeves and tungsten carbide coated sleeves are also available.
Range
| Shaft Sleeves | Worman® Pumps |
|---|---|
| B075 | 1.5/1B-AH, 2/1.5B-AH |
| BSC075 | 50B-L |
| C075 | 3/2C-AH, 4/3C-AH, 75C-L |
| CH075 | 1.5/1C-HH |
| D075 | 4/3D-AH, 6/4D-AH, 100D-L, 3/2D-HH, 6/4D-G |
| E075 | 6/4E-AH, 8/6E-AH, 8/6R-AH, 150E-L, 10/8E-M, 4/3E-HH, 8/6E-G |
| F075 | 8/6F-AH, 10/8F-M, 6/4F-HH, 10/8F-G |
| FAM075 | 10/8F-AH, 12/10F-AH, 14/12F-AH |
| G075 | 12/10G-G, 14/12G-G, 12/10G-GH |
| S075 | 300S-L |
| SH075 | 10/8ST-AH, 12/10ST-AH, 14/12ST-AH |
Slurry pump base basic part number is 003, it is the main part which hold the other slurry pump parts, it is a one piece casting cradles the bearing cartridge assembly. There is a adjusting screw below the bearing housing which is a simple impeller clearance adjustment facility.
Mr. Arvind Sharma (Mineris India Pvt. Ltd.)
4th Floor, A/403, Sai Platinum, Amar Javan Chowk Road, Opp. Sankalp International School, Nikol, Ahmedabad, Gujarat - 382350
Share us via
