Our Products
It is used to produce the chick in the firm
Product:The incubator ismade up of plywood in the exterior and plain sheet in the interior. Its wall is about 10 cm thick and thermocole is used to make it insulated. The whole device is divided into two chambers, upper and lower. The upper chamber houses the main component of the incubator i.e. the egg tray and source of humidity. While the lower chamber houses the thermal source, the speaker and the switches.Here the innovator uses electric lamp as the source of heat when electric current is available and in case of power failure the source of heat would be kerosene lamp. Both the light and the lamp heated the floor of the upper chamber (ceiling of the lower chamber). There is a regulator (same as that used in fan) by which the intensity of the light can be altered. This partition is made up of two-plane sheet and nothing is there in between, so the heat can easily be transfer. For the humidity a plate is placed below the egg try. From the try water gets evaporated due to heat and makes the chamber humid.In this incubator air is feed from four holes in the bottom which are connected with the upper chamber by four hollow pipes.
Technical specifications:
Key Competitive Advantage:
spray pump which generates pressure to spray the pesticides.
Problem addressed:
Spraying of agrochemicals in the field is a tedious and laborious task. The conventional knapsack sprayers available in the market require manual labor to operate, which is difficult to find due to movement of farm laborers toward cities. The small farmers cannot afford to buy the power operated sprayer or tractor-mounted sprayers available in the market, as these are very costly and are of not much use to small farmers due to small land holdings.
Product:
Mansukhbhai Jagani, a farmer cum artisan with a passion for mechanical innovations developed a bicycle operated sprayer, which is very efficient and affordable by the farmers. is an attachment, which essentially uses the circular motions of the cycle sprocket to move the piston of the spray pump which generates pressure to spray the pesticides. The front and rear sprockets of a thrown away bicycle are interchanged and the small sprocket is connected to the piston pump, so as the circular motion is converted to reciprocating motion of the piston and thus the pressure is generated and thus the pesticides are sprayed on the field
Technical specifications :
Gas after filteration is feed to engine.
Problem addressed:
There are lots of villages in the country which are still not electrified or are receiving power erratically. Given the limited global supply of fossil fuels, search for renewable energy has been on the top of the sustainability agenda.Biomass gasification, a century old technology, is viewed today as an alternative to conventional fuel. In gasification process, wood, charcoal and other biomass materials are gasified to produce so called producer gas for power or electricity generation. Mr Rai Singh Dahiya observed that the users of biomass gas (producer gas) as a fuel generally complain about choking in the engine after running for a certain period of time. He solved this problem
Product:
The innovator has changed the conventional designof gasifiers specially the filters and cooling unitsto get clean gas and ensure smooth operation ofengineat low operational cost. It is a down draft typebio mass gasifier, compact and efficient system for converting Bio Mass into producer gas which isused as a fuel in running Diesel Engine by makinglittle modification on engine. The Biomass is burntin a furnace packed from all the sides and havingone outlet to pass the gases to other chamber wherethese gases are cooled and then passed through thefilter for filtration. This filtered gas is then feed tothe engine, as a substitute to diesel or likeother fuel, for its running.
Technical specifications :
It can be used by any Food Processing Industry
Product:
The innovative machine can be effectively used by any Food Processing Industry such as pickles or masala manufacturers. Large quantities of lemon to the required shape and size can be cut in a continuous fashion. Better quality of slices produced- slices of fruit produced are of a uniform nature and are neatly and conveniently collected and recovered.
Technical specifications:
Key Competitive Advantage:
innovative stove is a double-chambered efficient portable stove
Problem addressed:
To meet their cooking energy needs, large numbers of households in the countrys poorer, rural areas use traditional chulha/ stoves, which consume firewood and other biomass as fuel. The fuel efficiency of traditional chulhas is very very low and burning solid fuels indoors results in high levels of toxic pollutants, a major risk factor for lung cancer, and cardiovascular and respiratory disease.
Product:
Jayprakashs innovative stove is a double-chambered efficient portable stove. It can use coconut shell or wood as a fuel.Innovator has improvised the stove by incorporating a secondary combustion chamber for burning the un-burnt bio mass and hydrocarbons coming out with the smokes/exhaust. As a result, the thermal efficiency of the stove has improved while the pollution has reduced.
There are two layers of ceramic materials having 2 inch gap between it. The outer wall also has two openings for air inlet and the inner wall has secondary holes that facilitate the burning of smoke that enhances the fuel efficiency. The air enters through the outer wall gets heated in the annular chamber, and it enters through the holes through the combustion chamber and hence provides full combustion.
Technical specifications:
This stove is transportable and has high burning efficiency 37.6% against an efficiency of 17% with other stoves.
Different kinds of fuel woods, bio mass can be used.
Key Competitive Advantage:
Besides the portable wood stove, he also manufactures and sellsCommunity stoves & Domestic stoves.Community stoveis made of bricks, cement, clay, cast iron and can cook food up to 100 kg.Domestic stoveis a miniature of the community stove. This stove is fixed on the platform in the house and can cook food for household needs.
It removes lint from the cotton shell in faster and efficient manner
Product:
As an answer to this problem, Mansukhbhai developed a Cotton Stripper machine, which removes lint from the cotton shell mechanically, faster and efficient manner and leave it ready for ginning. The machine consist of feeding units, electric motors, cylinders brush rollers, wire mesh rollers, suction unit and cleaning units. It can alsobe wheel-mounted for easy mobility,
Technical specifications :
Key Competitive Advantage:
It is designed for peeling garlic in bulk quantity
Product:
Innovator has developed garlic-peeling machine, which peels garlic while maintaining the original property. It is fully automated machine, made from food grade quality material. It is designed for peeling garlic in bulk quantity, is energy efficient, and saves labour. It economizes operating cost and removes capacity constraints caused by shortage of human labourers in peak seasons for pickle industry. The peeling effectiveness is very high at about 90% while the damage to the peeled garlic is very low at about 2%. This machine is maintenance free and requires only labor during operation to feed the garlic.
Technical specifications:
Key Competitive Advantage:
farm implements for agricultural operations consisting of shallow ploughing, sowing and inter culturing
Product:
Using the self fabricated chassis, drive and power of an Enfield Bullet motorcycle in front the innovator has retrofitted an attachment with two wheels at the rear with a tool bar to fit various farm implements. The rear wheel of the motorcycle has been removed and an innovative assembly unit has been attached. It can also be designed and attached to locally available Chhakdo rickshaw or assembled vehicle having minimum 6.5 HP engine. This meets various needs such as ploughing, weeding and sowing seeds and spraying. It can improve productivity and reduce operating costs for farmers, who currently use bullock-driven plough and cannot afford the tractors or power tillers.
Technical specifications :
key features
generating electricity where a continuous flow of water is available
Problem addressed:
Electricity is the basic necessity and there are number of places where electricity is not easily accessible due to difficult terrain. Mr. G.K Ratnakar of Jayapura village of Karnataka designed a modified hydro turbine to generate electricity which can be simply installed in a stream of flowing water.
Product:
Modified hydro electric turbine is an innovation which can be used for generating electricity through flowing water. It is primarily designed for remote areas where it is not possible to supply electricity through conventional electricity transmission lines. The number of such locations is quite enormous in hilly & forest areas of the Western ghats, North-east, etc. The modified hydro turbine is an environmental friendly & cost effective measure for generating electricity where a continuous flow of water is available. The major components of this turbine include alternator, balance wheel & belt pulley, V-belt & V-pulley. The novelty of this innovation is that it can be also installed in the stream of running water & the design of the turbine can be customized according to the requirements.
Technical specifications :
Key Competitive Advantage:
The device suits best for mixed cropping and saves labour and time consumed in clearing seed containers for next seed sowing.
Product:
It is a seed drill system having a unique seed metering mechanism. It enables farmers to carry out multi-seed sowing either simultaneously or separately.The automatic seed drill having a cup and cone type seed metering mechanism, has been designed for mixed cropping especially for small seeds. The machine consists of a taper worma and taper brush fitted around the taper worma. When the tapper worma rotates at the operating end then the crop seeds come from seed hopper with the help of screw worma and these pass through the taper brush. Now these seeds pass on to the distributor through which seeds are distributed uniformly in all directions. A handle, which is attached to the main shaft helps in lifting up the machine. This handle lifts the shaft and prevents wastage of seed crops at the sowing time.
The technology has tremendous potential in dry and hot climatic conditions (i.e. tropical) and where electricity is not availabl
Product:
The Natural Water Cooler is a low cost, energy efficient, environment friendly water cooler that is based on the principle of heat exchange. It cools water naturally according to the external temperature and humidity. Water passes through cotton string covered copper coils, which are continuously being moistened by a dripper. A small DC fan operated through solar panel mounted on roof top facilitates the air circulation and evaporation of water from the cotton string on the coil cools the water inside. It reduces the temperature of input water by 8 to 10 degree centigrade depending upon the external temperature and humidity. It also has an in-built filter that provides clean and hygienic water. The external casing of copper coil is made of steel with sufficient ventilation. The use of copper tubes for flow of water has health benefits too. It has to be located in an area where there is sufficient ventilation and should not be directly exposed to sunlight.
Technical Specifications :
Key Competitive Advantage:
. When the tractor moves forward, the fertilizer metering mechanism gets the drive to release the fertilizers in the tubes.
Product:
It is a tractor drawn semi - automatic Onion transplanter. It can perform three functions at a time viz. transplanting the onion, applying the fertilizer and making the irrigation channels. When the tractor moves forward, the star wheel type metering mechanism gets the drive to release the fertilizer in the tubes. The seedlings are delivered manually in the delivery chutes for planting. The inter-row and inter-plant spacing can be adjusted in the machine to a finer level. Two depth controlling wheels fitted on either ends of the equipment maintain the uniform depth of onion planting, which is kept at 1 cm. A channel forming ridger plough is mounted offset to the right end of the transplanter to form the irrigation channel simultaneously
Technical Specification:
Key Competitive Advantage:
Innovator has developed a reversible reduction gearbox and a manually tiltable Z-drive system for small capcity diesel engine.
Product:
Innovator has developed a reversible reduction gearbox and a manually tiltable Z-drive system for small capacity diesel engine. The use of this system reduces the daily fuel consumption and thereby the cost by about 60 to 70% (as compared to kerosene run marine engines) by enabling them to shift from a kerosene run outboard engine system to a diesel powered inboard engine system. It is absolutely pollution free as compared to the conventional kerosene/petrol engines.
Technical specifications
Key Competitive Advantage:
It makes the use of the smell from the septic tank to attract the mosquitoes.
Product:
The main specialty of this device is its scientific and eco friendly nature that makes it different from other machines. The strategy used in this machine is making obstructions for the reproduction of Mosquitoes. Hawker indirectly destroys 45000 mosquitoes by simply killing one single female Mosquito. Hawker is the most effective way to combat your existing Mosquito problem without any application of pesticides or chemicals. Thus, it helps to avoid the use of insect repellents that contain the toxic Allethrin.
Technical specifications:
cooking vessel having two compartment for making sambhar as well as rice separately
Product:
Modern rice cooker don't facilitate the draining of starch water, which contains more carbohydrates that cause blood sugar and high BP
Innovator has developed a cooking vessel having two compartment for making sambhar as well as rice separately but simultaneously. For cooking rice, in one compartment, innovator provided perforated plate and outflow pipe at the bottom so that one can easily drain starch water once cooking is over.
Technical Specification:
He developed a unique process of manufacturing soap that floats in water
Product
He developed a unique process of manufacturing soap that floats in water. Different innovative process is followed while manufacturing this soap to keep its density lighter than water so that it can float on water.
Mitticool is a natural refrigerator made entirely from clay
Product:
Mitticool is a natural refrigerator made entirely from clay to store vegetables, fruits and also for cooling water. It provides natural coolness to the stored material without requiring any electricity or any other artificial form of energy. Fruits, vegetables and milk can be stored fresh without deteriorating their quality for 2 to 3 days retaining their original taste. It works on the principle of evaporation. Water from the upper chambers drips down the side, and gets evaporated taking away heat from the inside, leaving the chambers cool. The top upper chamber is used to store water. A small lid made from clay is provided on top. A small faucet tap is also provided at the front lower end of chamber to tap out the water for drinking use. In the lower chamber, two shelves are provided to store vegetables, fruits and milk etc.
Technical specifications:
Key Competitive Advantage:
clay tawa with food grade non-stick material
Product:
Non-stick clay tawa is a combination of traditional and modern technology. The clay tawa is coated with food grade non-stick material, which prevents food from sticking to the tawa. Clay also adds a unique natural taste to the food.
Technical specifications:
The machine is for removing buds from the sugarcane sticks
Product:
The machine is for removing buds from the sugarcane sticks. These buds are used for sugarcane plantation in horticulture.
Technical specifications:
Key Competitive Advantage:
mechanically digs out the left over pods from the soil
Product:
The innovator has developed a tractor operated machine, which mechanically digs out the left over pods from the soil.It consists of elaborate system of crankshafts, flywheel, connecting linkages and rotating vanes on a shaft. A sieve is provided with a vibrating mechanism to filter the groundnut from the soil. As the tractor moves forward, the vanes rotate and dig into the ground, scoop and drop the soil-groundnut mixture into a vibrating storage unit with a sieve base. The system of linkages and drives vigorously vibrate the entire unit to shake the soil loose and the groundnuts stay trapped at the top in the central storage unit as the soil gets sifted out onto the ground. A window hatch is provided at the back that can be lifted and the groundnut taken out by a person into a basket
Technical specifications:
Key Competitive Advantage:
low cost can be mounted on a tractor and digs very fast and uniformly.
Product:
The trench digger developed by innovator is tractor-mounted machine that makes trench with sharp edges rapidly.The machine has a long arm having a rotator chain over it and sharp edged blades mounted over the chain. These blades cut the soil and throw it out as the chain rotates continuously. This chain is supported by a large wheel at the rear end of the arm and two mini wheels framed up on the main frame slot. The arrangement consists of a planetary gear system and motion converter unit to deliver power from the tractor, a chain gear and roller system and a belt with sharp trench digging blades of high carbon steel. An additional gear drive system is mounted within the wheel of the tractor to convert the 550 rpm of the tractor wheel to the desired 90 rpm speed of the shaft.
Technical specifications:
Key Competitive Advantage:
Useful for climbing tree
Product:There are three variants Coconut Tree Climber, Multi Tree Climber and Tree Walker. Upper frame is operated by hand and lower frame is operated by leg. By up and down movement of upper and lower frame, one can climb on the tree.Multi Tree Climber Equipment is suitable for climbing coconut, palmyra, teak, and rubber, silver oak & similar trees.
Key Competitive Advantage:
|
Product:This windmill has unique design. It is not aerodynamic but it is a DRAG TYPE low height windmill for lifting ground w
Problem addressed:
Use of wind turbine is one of the oldest methods of harnessing energy from wind to pump water. However, majority of the windmills available in the market are Aerodynamic windmills. These types of windmills require high cut-in speed (minimum wind speed requires for starting, i.e. about 12 to 15 km/hr) and this is a major limitations for majority of the Indian geographical area except coastal area. It also requires high maintenance and very expensive also.
Technical Specifications:
The machines are easy to operate and maintain.
Problem addressed:
Sanitary napkin, a universally needed product, has very low penetration in India and other developing countries, partly due to its high price and partly due to the tradition of using cheaper but unhygienic old cloth piece. As a result they become the host of many infectious diseases. This is due to lack of awareness and economic inability for adopting better precautions like use of good sanitary napkins during menstruation period. Usually different varieties of sanitary napkins are found available in the market but they are very expensive and are not affordable for rural & under-privileged women and girls.
Product:
Muruganantham has developed a set of four different small machines namely de-fiberation unit, core forming unit, sealing unit and UV sanitizing unit, which reduce the cost of production making products affordable to all. The production rate using manually operated machine set is 900 to 1000 napkins/day while with semi automatic machine set it is 3000 napkins/day (production efficiency may vary depending upon the skill & speed of operators). The machines are easy to operate and maintain.
In the first stage, by using deliberation unit, the raw material in the form of wood fiber is de-fibred to produce soft pulp. In second stage, de-fibered pulp is given required shape of the napkin in core forming units operated by a foot pedal. The third stage involves sealing the pads. The fourth stage involves passing the sealed pads through a dedicated Sterilization unit. Once the sterilization is complete, the pads are ready for the finishing operations consisting of trimming, position strip fixing, packing and dispatch.
Technical specifications :
(Note: Production efficiency may vary depending upon the skill & speed of operators.)
De-fibred size of wood pulp filament: 1-1.5 mm.
Key Competitive Advantage:
manually operated as well as a power-driven milking machine
Problem addressed:
Safe milking of cow/buffaloes is a requirement across rural India. In rural area, availability of skilled labor formilking is also a problem now days. Adding to this is the fact that milking by hand is not considered healthy or hygienic anymore. Power operated milking machines are available in the market which are very expensive, suitable and affordable only for large cattle farms.
Product:
Innovator has made a manually operated as well as a power-driven milking machine that helps small farmers to milk animal hygienically and reduce the drudgery in the process. It is a very simple machine and can be easily operated by women as well.
Technical Specifications:
The machine is available in four variants 1) Manually operated (Hand Driven) 2) Semi Automatic Single cluster AC motor driven 3) Semi Automatic Double AC Motor Driven and 4) Semi Automatic 12 V DC battery operated. All these models are made from Food Grade Stainless Steel material and equipped with Cluster assembly with four teat adapters with silicon rubber teat liners, transparent milk, and vacuum pipe. 100-gram vacuum grease and two O-rings are provided as spares. In this entire model, the vacuum level required for milking is 350 mm Hg. The model wise technical details are as below.
Key Competitive Advantage:
we can drink expresso coffee at home
Problem addressed:
Coffee is not an available option at majority of the places and most roadside tea stall owners provides tea only. The electric coffee making machines were very costly (more than Rs.5000) and out of reach for most road side vendors
Product:
The innovator has modified the normal pressurecooker and made it into a coffee making machine.A simple attachment of a metal pipe along with pressure releasing valve has been provided inthe cooker lid. Cooker with water is heated overstove. Once steam is formed, it is released throughthe metal pipe and collected in a jar containing mixtureof coffee powder, milk and sugar. After allowingsufficient steam into the jar, in a few minutes, frothyand tasty coffee is ready.
Technical specifications:
Key Competitive Advantage:
very cheap and important innovation for medium class farmer
Problem addressed:
Not all the farmers in the country can afford bullock, a small tractor or power tiller. Also due to relatively low land holding capacity many farmers do not need these farm equipments.
Product:
Bicycle weeder is a multipurpose farm implement developed by using inexpensive bicycle components. The main part of the implement consists of the front portion of a bicycle, namely handle bar, front axle and the wheel. A steel fork is connected to the axle and other end carries different attachments. Separate attachments for weeding and tilling are attached to the working end using bolts and nuts. This helps in changing the attachments as needed. The load in digging out the soil has been kept to the minimum by providing appropriate profiles and curvature to the implements. Suitable slots are provided for attachments so that the distance between the blades can be adjustable to suit specific requirements.
Technical specifications:
convert biowest int o manure
Problem addressed:
Fertility value of well decomposed compost is well known. Decomposition can be hastened if the biomass is aerated, humidified and properly mixed. It is a time consuming (about 3 months) and laborious task to preparethe manure. The technology for thorough mixing the compost for rapid compost mechanically is available abroad, although no such domestic product is available.
Product:
Innovators machine is a tractor PTO driven machine, which can thoroughly mix and moisten the bio-waste, reducing the time of decomposition from 3-4 months to 20-45 days.The revolving blades of machinesmixes the waste material systematicallywhile as fine water spray is done simultaneouslyby the attachment fitted with machine. After completing the first round of mixing the materialis left for a day or two and process is repeated after an interval of 2-3 days so that process of natural decomposition takes place. After 4-5 days and repetition of mixing process 2-3 times, the compost is ready to use in Agriculture as natural/organic fertilizer.
Technical specifications: