Write a Review
Our Products
Our Complete range of products are Rerolling Mill Duty Motor, Vertical Hollow Shaft Motor and Mill Duty Motor.
New India offers specially designed motors for Rerolling Mill Applications. Our motors are rugged, heavy duty, compact, and maintenance friendly. Their shock resistant construction takes care of the heavy mechanical jerks and electrical spikes in current due to heavy load cycles.
| Functional, Rugged, Heavy duty, Compact & Maintenance friendly. | ||||||
| Shock resistant construction in cast Iron & Steel fabricated body. | ||||||
| Rotor is specially designed with tight-bar-in-slot construction with taper section to obtain adequate stating torque & critical load factors. | ||||||
| Stators & Rotors are flood impregnated with polyester resin varnish to ensure longevity of protection against chemicals and moisture. | ||||||
| A high carbon, hard steel shaft with a large cross section provides, strength with minimum deflection & vibration. | ||||||
| Heavy duty Bearings, Brushgear & Slipring ensure high efficiency even under severe operational conditions. | ||||||
| Design ensures efficient ventilation & heat transfer from windings & cores. Can offer IP23/IC01; IPW 44/IC01; IP55/IC61; IP55/IC66; IP55/IC81 | ||||||
| Terminations are provided in a large box to ensure full electrical clearances & insulations. | ||||||
| Use low-loss magnetic core stamping & high conductivity copper conductors (solid & wire) for windings, with class B/F insulation. | ||||||
| With a design that has proved itself over 3500+ machines that have been deployed in the last 50+ years clearly this is the choice for all suitable applications. | ||||||
| Can take and sustain high number of sudden overloads.
|
New India offers specially designed Vertical Hollow Shaft Motors for Vertical turbine pumps. The special design makes them easy to install & maintain. The design ensures a proper & permanent shaft alignment with the pump. Motors are provided with a Non-reversible ratchet that prevents the reverse rotation of the motor due to the back flow of water or phase reversal. The Motors are provided with bearings having ample thrust capacity. The bearings are capable of taking the entire thrust load of the pump shaft assembly and the water column.
APPLICATIONINDUSTRIESFor Vertical turbine PumpsIrrigation ProjectsPower/Steel/CementPaper Industries
| Specially designed for Vertical Turbine Pumps. |
| Easy Installation as maintenance. |
| Permanent shaft alignment. |
| Well Protected construction. |
| High thrust Capability. |
| Rugged design. |
| Anticlockwise direction of rotation looking from top of the motor. |
| Non-reversible ratchet, which prevents the reverse rotation of the motor due to the back flow of water or phase reversal. |
| Motors are provided with bearing ample thrust capacity. Bearing are capable of taking the entire thrust load of the pumps shaft assembly & the water column. |
| Metalic fans for effective cooling in shorter cycles. |
| A unibake component painting system at controlled atmosphere ensures quality finish, scratch and durability. |
New India offers Mill Duty Motors specially designed for Steel Mill Drive applications. Motors are also used in Overhead Cranes & Cement Mill Drives. Motors confirm to AISE technical report. Motors are supplied with full speed, half speed and quarter speed designs based on requirement.
| Steel Mill Drives |
| Overhead Cranes |
| Cement Mill Drives |
SALIENT FEATURESConforming to AISE technical report no. 1-1991 / IPSS 1-03-002-94.Full speed, half speed and quarter speed designs available.Suitable for operations up to 500 volts.Suitable for operation on 3 phase, 6 pulse thyristor converter.Class H insulation with class F temperature rise limits.Armature class H with VPI in solvent less polyesterimide resin.TIG welding of armature coil connection to commutator.Split / Non split yoke without compensating winding or non-split laminated yoke with compensating winding. However, split yoke is preferred for 808 & above frames and compensating type for 812 & above frames.Replaceable shaft.Double shaft extension 1:9.6 taper with key way paralle to taper as per AISE or 1:10 taper with key way parallel to shaft axis as per IPSS.Convertible between TENV & TEFV enclosure or with top mounted blower unit.Loose hanging leads or terminal box as required.Axial play of 3 mm approximately of shaft.Brush position of 45 deg. For easy access for maintenance (except in case of laminated yoke version).Motor mounting dimension can be matched to replace 600 series motors to AISE or Russian standard.
Hemanshu Desai (New India Electricals Ltd.)
39/2 J. C. Road, 560002, Jc Nagar, Bangalore, Karnataka, India
Share us via
