Other Products / Services #5809646

Spring loaded roller is capable of applying fixed load of 50N (5 Kgs) as per the standard when pressed. Caltechs compact spring loaded roller can be held by hand firmly, easily pressed to get desired load and reduce human errors for applying constant pressure to provide best dust test results. Calibration adjustment is possible simply by adjusting nut. One single broad roller spring loaded roller along with dust test kit helps to accurately determine size and particle size of dust particles on steel surfaces prior to painting. Assure equal pressure for the complete tape to get best results. No maintenance required for this instrument.

Use of spring loaded roller assist to improve adhesion of coating and premature failure of coating. Dust on blast cleaned steel surfaces may reduce the adhesion of applied coatings and by absorbing moisture may promote the corrosion of the blast cleaned steel.

The Paint Inspectors Kit is a comprehensive kit of equipment, which will cater for the day-to-day standard requirements of the Industrial Painter and Inspector.The Paint Inspectors Kits contains the following listed equipment. Paint Inspector Kit in one carrying case with the entire basic test instrument make inspectors job easy. Highly recommended for QA / QC dept. of paint shops

The importance of proper lighting for color matching need not be emphasized due to the phenomenon of Metamerism samples appear to match in one illuminant and mismatch in other illuminants.Scan-O-Lite offers you consistency in illumination, whether it is in the day or night or whether you are examining color in your factory, office or at the customers end.You are assured of uniform and standard illumination. Scan-O-Lite is a very important tool for your modern laboratory and on your shop floor.Immediate visual check for metamerism, fluorescent pigments and strength of optical brighteners etc. changes here

• Cabinet constructed from non-corrodible high temperature resistant glass reinforced plastic. Acrylic cover is provided.


• Constructed in fiber-reinforced plastic, 10 mm thick with stiffners at the bottom to take heavy load.


• The FOG Chamber conforms to ASTM B 117 specification. The volume is of sufficient size to test adequately the desired number of parts without overcrowding.


• The apparatus consists of a fog chamber, a salt solution reservoir, a supply of moisture free compressed air, atomizing nozzles, specimen supports, provision for heating the chamber, humidifying chamber and control system.


• The fog chamber is provided with digital temperature controller, pressure gauge, provision for controlling the mist, humidity indicator and solenoid valve to regulate these conditions.

• Interior construction of stainless steel 304


• Outer construction-PCRC sheet (as per requirement)


• 75mm glass wool insulated on five sides


• Provided with High speed stirrer with speed regulator


• Control panel provided on the side of oil bath two neon lights and an ON/OFF switch.


• Perforated and removable diffuser shelves


• Microprocessor based temperature controller (HMI+PLC as an option)


• Printer report program (optional)


• RS 232/485 interface (optional)


• USB ports (optional)


• Real time data acquisition system (optional)


• Profile control(MULTIPLE PROGRAMMING) (optional)


• Timer (optional)

• Large-capacity tanks for higher productivity


• Calibrations up to 300 C


• Built-in cooling coils for faster cooling


• The units are operated via an innovative and user friendly control panel which includes an LCD display, and offer configurable PID controller (HMI+PLC as an option)


• Visual and audible alarms in the event of a failure


• Dual protection system against uncontrolled over-temperature events:
  
  
  
  • Heating elements turn off automatically if measured temperature exceeds the set threshold by 5C
  
  
  • Mechanical over-temperature device shuts off heating elements if temperature exceeds maximum allowed values
  
  
  
  


• Variety of liquids that can be used


• RS 232/485 interface (optional)


• USB ports (optional)


• On off updates on mobile (optional)


• Real time data acquisition system (optional)


• Corrosion resistant inner and outer surfaces.


• Sturdy construction


• CFC free refrigeration unit, for low temperature requirements

INTERNAL DIMENSION

• 12X12X12
  


• 18X18X18


• 18X18X24


• 24X24X24

4 tubes electrical centrifuge basically used Pathological laboratories and hospitals for routine centrifuging tests. These are well known in the market due to their distinctive features like robust Construction, easy to use.

We make use of premium quality material and latest technology machines for the production of this doctor centrifuge by our industry senior most professionals.

Features :

Rust proof Aluminum body.

Best quality rotor with double enameled windings and coil

Fitted with imported carbon brush.

Fitted with vacuum feet for stability.

Single aspirations, with filter (Na K) final result in ppm, 2 digit dual LED display for simultaneous result along with compressor accessories, autoignition, Ca Li filter can be provided on request at extra cost.

Accessories on Request

a)filters (Na, K, Li, Ca) Anyone

b)Air Compressor

Construction:Single walled construction, the wall is made of thick high grade stainless steel sheet of SS304 grade. The lid is made of stainless steel sheet. . Provided with built??? in safety valve, pressure gauge, pressure release valve. The pressure is adjustable from 5 psi to 15 psi .The pressure with an accuracy of

+/- 1 psi. Supplied complete with chord and plug.

Mode of Heating:Electrically heated by special flange type/immersion type. To work on 230 volts singlephase.

Size: 12x12

Alcohol tester is a kind of tester designed to measure concentration result of the breathed alcohol in the human body.

Main Feature:

Advanced Flat surfaced alcohol sensor

Quick Response

SMD assembling, stable performance

Smart MCU control

Direct testing process LCD indication

Digital LCD display with light blue backup

Audio warning beyond preset limit

Sensor fault self checking

CircuitMicroprocessor LSI circuit.

Display61 mm x 34 mm supper large LCD display. 15 mm ( 0.6 ) digit size.

FunctionDual differential input, data hold, zero/relative, memory.

Zero adjustPush button on the front panel.

Operating Temp0 to 50 ( 32 to 122 ).

Operating HumidityLess than 80% R.H.

Features:

The portable anemometer provides fast accurate readings with digital readability and the convenience of a remote sensor separately.

Multi functions for air flow measurement: m/s, km/h, ft/min, knots.

Low friction ball bearing design resulting in accuracy at both high and low velocities.

Conventional twisted vane arms, always a source of unreliability have been eliminated.

DATA HOLD.

Compact housing cabinate.

Wide applications: use this anemometer to check air conditioning heating systems, measure air velocities, wind speeds, temperatureetc.

Detection Distance10 mm for one rupee coin, 120m for iron pipe or tube of 20mm diameter 110mm for a dragger.

Detection SensitivityContinuously adjustable with the help of a knob as per requirements of various applications.

Metal Detection IndicationA unique audio tone beep red LED visual indication indicate presence of metallic object.

Stop Watch Count Timer Mode

Double Count Timer Mode

Display Double Count Timer

Display Time Calendar week and alarm time

Time and Day setting

Alarm time setting

Salient Feature

An Ideal Instrument for use in all industries many other substances coming within the range of the instrument. Dual Scales: Oil Scale 0100 with micrometer

Sugar Scale sub divided at 1% interval so as to measure up to 0.0001.

Transmitted light can be used for transparent solutions. Reflected light for dark or semiopaque substances.

Color in the border line can be eliminated by a compensating prism and the increase in definition obtained gives creator accuracy of measurement.

a) 032%

d) 010%

e) 018%

h) 0100%

028%

*Disp Indoor temperature and humidity, Outdoor temperature;

lay*Record the maximum a minimum temperature and humidity; *Deg. and deg switch;

nd *Freeze from 1 to +4; *Temperature measure range: Indoor: 10+50(+14+122) Outdoor: 50+ (58+158) *Humidity measure range:2099%RH; 70*Accuracy: +/1, +/5%RH; *Time and Alarm

*Battery: 1x 1.5V operation (AAA);

*Figure Size: 110 x 100 x 22 mm

Salient Features:

No lubricant required

Noiseless performance

Absolutely portable

Totally oil free construction

Practically maintenance free

All parts made from special graded Aluminum die cast material for light weight and good strength

Diaphragms are made of special 2 ply nylon reinforced neoprene rubber.

Valves made of SS 316 material

Built in micro suction filter

Extra large bearings for trouble free and smooth running.

• Kinematic viscosity is of primary importance in the design and selection of a wide range of petroleum products. Calibrated capillary viscometers are used to measure flow under geavity or vacuum at precisely controlled temperatures.


• Rectangular model having double walled construction with toughened glass observation window (254 W x 225 H mm).


• Illumination from rear side provided.


• Oil immersion heater.


• Bath opening 254 x 200 mm with cover having 6 openings of 50 mm in diameter to hold 6 viscometers with six bakelite holders.


• Liquid capacity 22 Litres.


• Microprocessor based PID temperature controller withPT-100 digital read out, resolution, temperature accuracy of 0.02C.


• Efficient stirring system

• The ability of a lubricating oil to separate from water and resist emulsification is an important performance characteristic for applications involving water contamination and turbulence. Water separability is determined by stirring equal volume of water and sample together at a controlled temperature to form an emulsion and observing the time required for separation of the emulsion to occur. This method is suitable for petroleum oils and synthetic fluids.


• Rectangular model having double walled construction with toughened glass observation window (230W x 200H mm).


• Illumination from rear side.


• 4 place Herschel Emulsifier.


• Added advantage of the stirrer being easily moved to each test position instead of moving the samples.


• Digital temperature, speed and timer


• Timer stops the stirrer after 5 minutes automatically and audible alarm.

• Foaming of lubricating oils in applications involving turbulence, high speed gearing or high volume pumping can cause inadequate lubrication, cavitation, overflow and premature oxidation. The sample is blown with a controlled volume of air at different specified temperatures. The resultant foam is measured at the end of each aeration period and at different intervals afterward.


• Rectangular single / double foam test model with double walled construction with toughened glass observation window
  (75W x 385H mm) suitable for 1, 2 3 sequence.


• Illumination at rear.


• Stirrer, heater and cooling coil installed in each bath.


• This method consist of single / two test bath large enough to permit immersion of 1000ml graduated cylinder.


• Digital temperature controller with PT-100 sensor.


• The gas diffuser is of 1 dia spherical made up to crystalline alumina grain.


• Air flow meter with needle valve to maintain an airflow rate of 94 5ml/min through the gas diffuser stone.


• Diffuser arrangement consists of diffuser stone, air tube and gasket.


• Electric air compressor diaphragm type.

These standards describe the determination of colour numbers of mineral hydrocarbons such as undyed motor and aviation gasoline, jet propulsion fuels, naphthas and kerosene and in addition petroleum waxes and pharmaceutical white oils and similar products. The colour allows to draw conclusions upon the refining grade.

• The equipment comprises of base stand with prism optics, graduated sample tube with cock, standard tube, removable frosted mirror housed in a base of the equipment, set of colour disc complete with three full discs and one half disc colour standards and hinged conversion table.


• Artificial day / light source housed in a separate metallic casing with ON/OFF switch.

• These standards describe procedures for testing the rust preventing characteristics of steam turbine oils, hydraulic oils and all kinds of gear oils in presence of water.


• 4 and 6 place constant temperature oil bath models with 400ml beakers, covers, stirring paddles, specimen holders, thermometers and steel test specimen.


• Temperature range ambient to 100C, 0.5C .


• Speed upto 1200 rpm, 25 rpm.


• Power supply : 230 V, 1 Phase, 50 Hz.

• These methods used to evaluate the oxidation stability of new and in-service engine, turbine and insulating oils in the presence of water and a copper catalyst.


• 2 Place rotating pressure vessels oil bath on castors.


• Digital electronic temperature controller with safety mechanical fail-safe thermostat.


• Heavy duty drive motor to rotate pressure vessel at 100 rpm and is housed below the oil bath.


• Rotating pressure vessel constructed of stainless steel with stem and valve to receive pressure transducer.


• Pressure vessel is held at an angle of 30


• Pressure mapping 0-200 psi.


• Temperature range from ambient to 200C.


• Capacity of bath is 70 litres with stainless steel body and top cover.


• Catalyst wire, glass liners with PTFE-cover, an ASTM 96C thermometer, O ring supplied with the unit.


• Automatic Pressure digital data logger with PC interfacing software supplied on CD-ROM with pressure sensor.


• Power supply 230 V, 1 phase, 50 Hz.

Emergency Shower are equipments that are designed to remove contamination from personnel prior to entering a clean room and are available in both standard and customized models. These provides on-the-spot decontamination. Laboratory Emergency Shower are a combination of stainless steel that will be accord with the lustration grade, firm and resistant chemical. These are suitable for cleaning eyes, face, hands, and spray head can be used for washing the whole body. Eye wash and spray shower can be used at the same time or they can be used separately. Switch of the spray shower is placed at the top of the handle and the flow is steady and simple.

Accidental chemical exposures can still occur even with good engineering controls and safety precautions. As a result, it is essential to look beyond the use of goggles, face shields, and procedures for using personal protective equipment. Emergency showers and eyewash stations are a necessary backup to minimize the effects of accident exposure to chemicals.

Emergency Showers can also be used effectively in extinguishing clothing fires or for flushing contaminants off clothing

Laboratory Fume Extractorare widely used for removing smoke, fumes, mist, and fine powder. Mobile fume hood extractor is primarily designed for various pharmaceutical laboratories, various research and development industries and light duty industry. These CE marked equipments are extremely durable, reliable and easy to operate.

it uses an activated carbon filter and fan to remove the smoke, and noxious fumes, created from soldering and other chemical processes.

Fume Extractorincludes a flame-retardant, self-supportive flex arm for easy and varied placement. Other benefits include small footprint, portability handle, heavy-duty casters for easy maneuverability, quick change pre-filter, and a variable speed controller. The product also known asPortable Fume Extractor.

it comes equipped with patented filtration media that is customized specifically for welding fume control. In most cases, HEPA filtration is utilized and is up to 99.97% efficient on particles 0.3 microns and larger. Other options include ASHRAE [up to 95% efficient on particles 0.5 microns and larger] and ULPA filtration media [up to 99.9995% efficient on particles 0.12 microns and larger].

If you are concerned about duct corrosion, hazardous stack emissions or other environmental factors associated with a fume hood you may want to consider a scrubber. Fume Hood Scrubber provides excellent air pollution control for water soluble chemicals present in the laboratory fume hood exhaust fumes. These Scrubber Fume Hood are designed to save space and provide effective air pollution control and operator safety protection for fume hoods. This is especially important for per chloric acid fume hoods, so as to prevent a build-up of potentially explosive perchlorate salts on the exhaust fan, as well as, on the exhaust ducting system.

Controller:Auto tuned PID controller with temperature range up to 200 deg C having
resolution of 0.1 degree centigrade.

Owing to our enriched industrial experiences, we are devoted towards manufacturing a wide variety of excellent qualityChemical Storage Cabinet.

• Measuring rate 18 s


• Storage temp. -40 to 70 C


• Battery type 9V block battery


• Battery life approx. 1 year


• Weight 168 g


• Dimensions 111 x 90 x 40 mm


• Material/Housing ABS


• Display LCD, 2 lines


• Warranty 2 years


• Sensor types NTC Testo humid. sensor, cap.


• Meas. range -10 to 70 C 2 to 98 %RH


• Accuracy: 1 digit 0.5 C (at 25 C) 2 %RH ( 2 to 98 %RH)


• Resolution 0.1 C 0.1 %RH

1. Temperature range up to 3500C


2. Recirculation fans with high efficiency motors to reduce energy consumption.


3. Microprocessor based controller (HMI+PLC as an option)


4. Simple calibration and auto-tuning function


5. LCD/LED display (0.1 resolution) and touch-sensitive keypad


6. designed to provide tight temperature tolerance and precise control for repeatable results


7. Ovens are exhausted to effectively remove the VOCs given off during curing, ensuring a safe environment.


8. Built-in timer and touch-button controls allows quick and simple temperature setting.


9. Robust structural oven frames and component supports


10. Corrosion-resistant interior and exterior.


11. RS 232/485 interface. (optional)


12. Universal Digital Data Recorder system(optional)


13. USB ports for PC connectivity (optional)


14. Temperature chart recorder/printer for printing graphs(optional)

1. Temperature range up to 10500F (5650C)


2. Microprocessor based controls (HMI+PLC as an option)


3. Simple calibration and auto-tuning function


4. LCD/LED display (0.1 resolution) and touch-sensitive keypad


5. u Silicone door seals


6. low noise circulation fans for better temperature uniformity


7. Counter-weighted top doors make manual loading and unloading easy and fast


8. High capacity compound horizontal airflow system


9. Air intake and exhaust ports with manual dampers


10. Differential air pressure switches


11. Separated, insulated, corrosion resistant inner and outer surfaces


12. Built-in timer and touch-button controls allows quick and simple temperature setting.


13. RS 232/485 interface. (optional)


14. Universal Digital Data Recorder system(optional)


15. USB ports for PC connectivity (optional)


16. Temperature chart recorder/printer for printing graphs(optional)


17. CE compliance.

Burn-in ovens are engineered for applications such as high dissipation forward bias, high-temperature reverse bias, dynamic and static burn-in of IC, RAM, ROM, microprocessors and other semiconductor devices.

Integrated Circuits (ICs) and other electronic devices are burned in at elevated temperatures to stress and exercise the devices under test. The high temperatures force early failure, known as infant mortality, at this point rather than later when they are in use in a finished product. This dramatically improves the reliability of the product. During burn-in the temperature rises as the air travels across the chamber due to the heat dissipated by the devices. High volume recirculation fans maintain consistent, uniform temperatures.

1. Temperature range up to 500 C


2. Microprocessor based controller (HMI+PLC as an option)


3. Doors with silicon gasket


4. Doors equipped with lock and key arrangement


5. Auto tuning and self-calibration function


6. LCD display with temperature display resolution of 0.1C


7. Inbuilt digital timer(Optional)


8. On-off heat switch


9. Air circulation with internal plenums for uniform airflow within the oven.


10. Robust, safe and reliable safe for drying.


11. Corrosion-resistant interior and exterior.


12. RS 232/485 interface. (optional)


13. Universal Digital Data Recorder system(optional)


14. USB ports for PC connectivity (optional)


15. Temperature chart recorder/printer for printing graphs(optional)

1. Maximum temperature range up to 10000F (5400)


2. Microprocessor based digital control system (HMI+PLC control system as an option).


3. Hi Tech double walled Oven


4. Digital temperature setting with an accuracy of one degree


5. Elapsed time indicator(Optional)


6. Simple calibration and auto-tuning function


7. Horizontal, recirculating air flow creates precise, consistent temperature uniformity throughout the oven.


8. Models are fully assembled and factory tested prior to shipment


9. Stainless steel interior minimizes corrosion problems and provides long life


10. turdy, welded, double-wall construction


11. Audio visual alarm for malfunctioning, over temperature, power failure etc.


12. RS 232/485 interface. (optional)


13. Universal Digital Data Recorder system(optional)


14. USB ports for PC connectivity (optional)


15. Temperature chart recorder/printer for printing graphs(optional)

• 8-digit LED display, clear reading


• Range and gate time adjustable continuously (100ms 10s)


• Selective range


• High stability

Features:

• Radio Controlled Clock with DCF, WWVB, JJY, MSF


• Time, SNOOZE, Month, Moon Phase, 12/24 Hour, C/F


• Month, Date, Week Display


• Indoor Hygro thermometer Trend Indicator


• Pressure Bar indicate History Trend


• Max/Min Temperature Humidity Records


• Max/Min Memory for Hygro thermometers


• Outdoor Thermometer From Max. 3 Different Wireless Sensors by 433MHz RF Transmission

Features:

• Relative measurement


• Diode test Continuity


• Buzz off


• Full symbols are used to indicate


• Prompted low-voltage


• Input impedance voltage measurement

Features and Benefits:

• Memory Depth: 40Kpts, 5Kpts/CH (SDS1202CNL)


• 6 digits hardware frequency counter, real time counting display


• Support SCPI programming command control


• Interface: USB Device, USB Host, RS-232, Pass/Fail


• Unique digital filter and data recorder function


• Embedded 12 languages, online help, one key storing and one key printing


• Up to 25MHz Bandwidth 1GSa/s sample rate


• 7TFT-LCD display, 8*18 grids


• Channels: 2CH 1EXT

Characteristic:

• The highest Single real-time sampling rate can be up to 500MHzsa/s; Equivalent sampling rate is up to 50GSa/s.


• Memory Depth: 32Kpts


• Trigger types: Edge, Pulse Width, Video, Slope, Alternative


• Unique Digital Filter function and Waveform recorder function


• Support Pass/Fail function.


• Thirty two parameters Auto measure function.


• Save/recall types: Setups, Waveforms, CSV file, Picture.


• Support Multilingual On-line help system


• Waveform Intensity and Grid Brightness can be adjusted.


• Support twelve types Language


• Standard Configuration Port


• USB Host: Support USB flash driver save/recall function and update firmware;


• USB Device: Support PictBridge compatible printer and support PC remote control;


• Pass/Fail Output.

• Compact design


• Reliable


• Eco friendly


• Microprocessor based PID controller


• Touch screen controls


• Excellent temperature uniformity

• Low cost


• Compact design


• Chamber made of stainless steel


• Large capacity


• Applications


• Asphalt testing

Gravity Convection Ovens are ideal for applications in which temperature uniformity is not essential, and where samples may otherwise be disturbed by a fan-generated airflow like powders and foils.

These ovens are constructed to remove the moisture as quickly as possible. They are extensively used in various pharmaceutical industries, food processing industries, laboratories and schools. They are incorporated with most developed and latest technology, provided with international safety standards.