Kolkata, West Bengal, India
Our Products
12 M.M. Tapping Machines Clutch Cone.Export quality liner clutch system make with use of specially processor trimentaly the clutch the liner clutch.
Pathak Automatic motorized wire nail making machines are simple and sturdy in design, high output, easy to operate and for long life service. All tools are easily accessible and can be quickly exchanged.
| PMM No. | Length of Nail in inch & mm | Wire Size S.W.G | Production P.M | Space Required in inch & mm | Motor H.P & R.P.M | Approx weight |
| 1 | ½ -1.1/2 12-38 |
16-20 | 350-400 | 30*30*29 750*750*725 |
2*1440 | 350 |
| 2 | ½ – 2 12-50 |
12-17 | 275-300 | 44*44*40 1100*1100*1000 |
2*1440 | 850 |
| 3 | ½ – 3 | 9-14 | 225-250 | 50*49*44 1250*1225*1150 |
3*1440 | 1450 |
| 4 | 1-4 | 8-12 | 125-150 | 58*57*46 1450*1425*1150 |
5*1440 | 2150 |
| 5 | 2-6 | 4-10 | 75-100 | 75*75*57 1875*1875*1425 |
10*1440 | 3800 |
| MODEL | Unit | VK-9 | VK-14 | |
| Cutting capacity | Round RectangleSquare | mm | 220 | 350 |
| mm | 250*125 | 350*150 | ||
| mm | 220*220 | 350*300 | ||
| Blade Dimension | mm | 2540*27*0.9 | 4100*34*1.1 | |
| Drive Motor | Power | H.P. | 1 | 2 |
| Speed | RPM | 1440 | 960 | |
| Power | RPM | 0.15 | 0.15 | |
| Speed | H.P. | 2800 | 2800 | |
| Blade Speed | Mtr/Min | 25-40 | 25-40 | |
| Overal Dimension(L*B*H) | mm | 1675*760*1395 | 1825*1090*1725 | |
| No | Parameter | Specification |
| 1 | Travel X Axis | 175 mm |
| Travel Y Axis | 115 mm | |
| Travel Z Axis | 115 mm | |
| 2 | Table Size length X width | 360 X 140 mm |
| 3 | Axis Control | Simultaneous Three Axis Control |
| 4 | Accuracy | 5 Micron each Axis |
| 5 | Spindle | |
| Speed range | 100 -2500 rpm min | |
| Morse Taper | ISO 30 | |
| Motor Power Cap | 0.75 HP | |
| 6 | Feed rate Axis | 2-50 mm / min |
| Feed Rapid Travels | 0 -700 mm / min | |
| 7 | Control system | PC-based 3 Axis Continuous path |
| 8 | Slides | Hardened & Ground Linear Guide Ways |
| 9 | Power source | 230 V, Single Phase 50Hz |
| 10 | Software | Programming and operating software and manuals with courseware and project book |
| 11 | Job scaling facility and canned cycles | Provided |
| Model | PFT-6 | PFT-8 | PFT-12 |
| Main Motor hp | 3 x 1440 | 5 x 1440 | 7.5 x 1440 rpm |
| MODEL | BLADE | TYPE | PLATE/SHEET | FLAT | ROUND | Net.Wt (APPROX) |
| UNIT | MM | MM | MM | MM | Kg’s | |
| VHS-200 | 200 | Geared | 7 | 75*8 | 16 | 40 |
| VHS-300 | 300 | Geared | 5 | 50*6 | – | 65 |
| TONNAGE | BHIW-65 Ton | BHIW-85 Ton | BHIW-115 Ton | BHIW-155 Ton |
| Maximum Capacity | 26 x 26mm | 30 x 20mm | 35 x 25mm | 30 x 30mm |
| Diameter x Thickness | 32 x 12mm | 38 x 15mm | 40 x 20mm | 44 x 20mm |
| Stroke | 70mm | 80mm | 80mm | 100mm |
| No.of Strokes(per/min) | 9~27 | 9~36 | 6~30 | 7~28 |
| Throat Depth | 240mm | 355mm | 400mm | 450mm |
| Round | 30mm | 50mm | 56mm | 80mm |
| Square | 30 x 30mm | 50 * 50mm | 56 * 56mm | 80 * 80mm |
| Angle Sectoin(90 Degree) | 120 x 120 x 12mm | 160 x 160 x 15mm | 180 x 180 x 14mm | 200 x 200 x 18mm |
| Angle Section(45 Degree) | 80 x 80 x 8mm | 80 x 80 x 10mm | 80 x 80 x 10mm | 100 x 100 x 10mm |
| Length x Thickness | 230 x 20mm | 330 x 20mm | 355 x 25mm | 300 x 30mm |
| Max. Length x Thickness | 375 x 10mm | 480 x 10mm | 600 x 15mm | 750 x 8mm |
| Blade Length | 400mm | 482mm | 610mm | 760mm |
| Shearing With Angle | 100 x 15mm | 120 x 15mm | 120 x 15mm | 120 x 15mm |
| Thickness | 10mm | 13mm | 13mm | 16mm |
| Width | 45mm | 50mm | 60mm | 60mm |
| Length | 90mm | 100mm | 100mm | 100mm |
| Length x Thickness | 500 x 5mm | 500 x 3mm | 700 x 3mm | 700 x 4mm |
| Length x Thickness | 120 x 58mm | 160 x 74mm | 200 x 90mm | 240 x 105mm |
| 90 x 11mm | 100 x 11mm | 120 x 13mm | 150 x 15mm | |
| 4kw | 5.5kw | 7.5kw | 11kw | |
| 1600kg | 2400kg | 3100kg | 5800kg | |
| (L x W x H) | 1700 x 900 x 1670 | 1930 x 900 x 1830 | 2240 x 850 x 1960 | 2700 x 1020 x 2116 |
The Pathak Planing machine has sufficient rigidity against heavy and accurate cutting operation. The bed, double column, table & cross rail are of rigid heavy box section casting duly seasoned. Automatic lubricating system on two V-guides for the table provided and table drive is by spur gear & rack arrangement.
| MODEL | HS12 | HS18 | HS24 | HS30 | HS36 | HS40 |
| Maximum working stroke | 14” | 20” | 26” | 32” | 37” | 42” |
| Length of ram without tool slide | 30” | 40” | 53” | 60” | 66” | 75” |
| Ram bearing in column | 20” | 26” | 31” | 37” | 41” | 44” |
| Ram bearing width | 7.5” | 10.5” | 12” | 12.5” | 12.5” | 14” |
| Tool Slide Traverse | 5” | 6” | 8” | 9” | 10” | 11” |
| Maximum distance from table to ram | 14” | 15” | 16” | 18” | 20” | 24” |
| Maximum distance from table to ram | 2” | 2” | 2” | 2” | 2” | 3” |
| Horizontal traverse of the table | 16” | 20” | 26” | 30” | 32” | 36” |
| No of speed | 3 | 3 | 4 | 4 | 4 | 4 |
| Length and width of cross slide | 25”*10.5” | 31”*11” | 38”*12” | 43”*12.5” | 46”*12.5” | 51”*15” |
| Top clamping surface of table | 14”*11” | 18.5”*12” | 25”*15” | 31”*16” | 37”*18.5” | 40”*20.5” |
| Size of base plate | 40”*16.5” | 50”*22” | 64”*23” | 76”*24” | 82”*26” | 90”*30” |
| Power required | 1 H.P. | 2 H.P. | 3 H.P. | 5 H.P. | 5 H.P. | 7.5 H.P. |
| Approximate net weight | 1200 kg. | 1500 kg. | 2000 kg. | 2300 kg. | 3200 kg. | 4000 kg. |
Hipat geared slotting machines are of very rigid construction with a good metal removing capacity combined with sustained accuracy. These are eqrally suitable for tool room or high speed batch production. The above mahcines suitable for various jobs, specially motor parts, scooter parts and intrnal teeth cutting etc.
| Technical Specifications | HSLP-1 | HSLP-2 | HSLP-3 | HSLP-4 |
| Stroke | 150 | 250 | 300 | 450 |
| Rotary table | 275 | 375 | 500 | 900 |
| Longitudinal movement | 200 | 280 | 300 | 600 |
| Cutting speed of ram stroke | 29,60,90 | 30,55,90 | 18,46,82 | 12,17,24/ 36,50,70 |
| Ram adjustment | 150 | 200 | 250 | 325 |
| Throat depth | 200 | 350 | 400 | 675 |
| H.P. Required | 1.5 | 2 | 3 | 7-5 H.P. |
| Distance from the tool rest to the main Column | 350 | 400 | 450 | 625 |
| Height between table & head | 300 | 375 | 450 | 700 |
| Gross weight (kgs.) | 975 | 1450 | 1900 | 4500 kg. |
| Width depth height of machine | 800*1100*1550 | 950*1325*1825 | 1125*1550*1925 | 2000*1800*1300 |
| Size of packing case W D H | 925*1225*1725 | 1000*1400*1975 | 1250*1600*2125 | 2350*2100*1500 |
The Universal Tool & Cutter Grinder is a robust machine capable of dealing with a wide range of tool & cutter Grinder operations. It is available as a steel cabinet mounted, machine and is designed for the rapid sharpening of H.S.S. milling cutters, spiral mills, metal slitting saws side and face cutters reamers, tap and with suitable attachments lathe tools, end mills formed cutters etc.
| MODEL | AMI 80 | AMI 87 | AMI 92 |
| Swing over table (Dia) | 230 mm | 305 mm | 350 mm |
| Maximum distance between centres | 305 mm | 560 mm | 660 mm |
| Table Longitudinal traverse | 305 mm | 510 mm | 610 mm |
| Table Cross travarse | 200 mm | 205 mm | 255 mm |
| Table Dimensions | 530 x 142mm | 805 x 156 mm | 1015 x156mm |
| Tee Slots width | 10 mm | 12 mm | 12 mm |
| Centre of wheel above table | 280 mm | 330 mm | 350 mm |
| Head Swivel | 90° | 90° | 90° |
| Head Swivel | 360° | 360° | 360° |
| Grinding Spindle Speed | 2800 rpm | 2800 rpm | 2500 rpm |
| H.P. of Motor | 1 HP | 1 HP | 1 HP |
| Floor arer occupied | 900 x 750mm | 1120 x 920mm | 1500 x 950mm |
| Height to the machine | 1500 mm | 1680 mm | 1500 mm |
| Weight of the machine with standard accessories | 500 kg | 670 kg | 825 kg |
Gear Hobbing Machine model V-300 is designed for the production of precision Spur, Helical, Worm Gears, Splines, Sprockets, Rachet Wheels & any other form that can be hobbed. Its bed & column are of close grain casting & are well ribbed with V-type guideways.
| Maximum continuous output (Max. Pitch) | 6 D.P. | 4 Module | |
| Maximum diameter of Gear with support | 14″ | 356 mm | |
| Minimum diameter of gear | 0.375″ | 10 mm | |
| Face Capacity for Spur gear | 8″ | 203 mm | |
| Minimum number of Teeth | 5 | 5 | |
Features :
