Sanghavi Group

Makarba, Ahmedabad, Gujarat

• Specially for floors
• Small and medium size tiles fixing
• For Internal use and External use

• Ready to use, needs no curing
• Suitable for tile on tile applications
• Excellent waterproofing characteristic
• Can accommodate thermal & physical movements
• Excellent adhesion, low shrinkage

• Plastered wall
• PCC / IPS
• Concrete (RCC) Surfaces
• ACC Block and all kinds of concrete

• 25 kg bag and Project packing of 40 kg bag is available on demand

• Available in Grey

• Factory sealed bags are best before 12 months from the date of manufacturing in unopenedcondition stored in dry area

• Add 25 kg of "MYMIX - CTA (Cementitious Tile adhesive)" to approx. 6.5 to 7.5 liters of cool and clean tap water
• Stir properly for 5 minute by hand or an electric stirrer to get a smooth and homogeneous mixture
• After stirring wait for 10 minutes, stir once again
• Now Apply the adhesive on the subfloor with the recommended adhesive notch trowel
• Check properly to ensure that the back of the tile is in full contact with the adhesive
• Remove excess adhesive immediately from the joints

"MYMIX FTA(Floor Tile Adhesive)" is a thin set Cementitious dry mix mortar For installing Ceramic, Vitrified tiles and natural stones for interior floor applications.

"MYMIX FTA"is polymer modified tile adhesive which make it ideal for fixing tiles, natural stones and granite to most building substrates.

• Specially for interior floors and walls
• Small and medium size tiles fixing
• For Internal use and External use

• Easy to Apply, single component adhesive
• Extended open time
• Superior adhesion properties with adhesion to varies substrates

• Concrete wall and floor area
• Tile - on - tile aplication
• Cement mortar beds

• Dual purpose for floor and wall with good adhesion workability
• Suitable for solid subfloors

• Thin - set cementitious screeds
• Cement Plaster

• 25 kg. Project packing of 40 kg size is available on demand

• Factory sealed bags are best before 12 months from the date of manufacturing in unopened condition stored in dry area

• Add 25 kg of MYMIXFTA (Floor Tile Adhesive) to approx. 6.5 litres. To 7.5 litres. Of cool and clean tap water and stir properly for 5 minute by hand or an electric stirrer to get a smooth and homogeneous mixture
• After stirring wait for 10 minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive notch trowel
• Press the tiles within 15 to 20 minutes with a shuffling movement in to the adhesive. Check regularly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints
• The proper preparation of the surface will make the fixing easier and quicker ensuring a better finish. The surface should be flat with a tolerance of 4mm over a distance of 2 meters. It is essential that you waterproof wet areas prior to tiling.
• New concrete is recommended to be 1 month old for every 25mm thickness and completely dried before tiling.
• Under normal circumstances, i.e. a temperature of 20 C and a relative humidity of 65%, the joints may be filled after minimum 24 hours.

• Multipurpose hipolymer modified thin set adhesive
• High bond Strength Suitable for exterior application of various tiles & stones
• High flexible adhesive

• Concrete
• Cement Plaster
• Cement mortar beds
• Brick Masonry

• Nonskid adhesive
• Water resistance properties
• Batter open time with good workability

• Ceramic tile & stone
• Cement Terrazzo
• Concrete Masonry
• Gypsum wall board (Interior application)

• 25 kg bag and Project Packing of 40 kg bag is available on demand

• Available in Grey & White

• Factory sealed bags are best before 12 months from the date of manufacturing in unopened condition stored in dry area

• Add 25 kg of "MYMIX - GTA (Glass Tile Adhesive) to approx. 6.5 ltrs to 7.5 ltrs of cool and clean tap water and stir properly for 5 minutes by hand or an electric stirrer to get a smooth and homogeneous mixture.
• After stirring wait for 10 minutes, stir once again and apply the adhesive on the subfloor with 2 mm adhesive notch trowel for glass mosaic
• Press the tiles within 15 to 20 minutes with a shuffling movement in to the adhesive. Check properly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints
• The proper preparation of the surface will make the fixing easier and quicker, ensuring a better finish. The surface should be flat with a tolerance of 4mm over a distance of 2 meters. It is essential to waterproof wet areas prior to tiling
• New concrete is recommended to be 1 month old for every 25mm thickness and completely dried before tiling
• Under normal circumstances, i.e. a temperature of 20C and a relative humidity of 65%, the joints may be filled after minimum 24 hours

• Single component adhesive mixed with water
• High bond Strength Suitable for exterior application of various tiles & stones
• High flexible adhesive

• NonSkid adhesive
• Water resistance properties
• Long open time with good workability

• Concrete
• Cement Plaster
• Cement mortar beds
• Brick Masonry
• Ceramic tile & stone
• Cement Terrazzo

• Concrete masonry
• Gypsum wall board (Interior application)
• Suitable for vertical cladding of vitrified tile and stones`

• Planning your layout is essential. Choose your starting point to create a balanced visual appearance. Trowelling should be done horizontally. Spread the adhesive on to the wall, working on small areas at a time. Tiles must be fixed before the surface of the adhesive forms a skin. The tile is then adjusted to its final position with an up & down movement so that full coverage is obtained to the back of the tile.
• The size of trowel used should be approximately as mentioned.
• Add 25 kg ofMYMIX STA(Stone Tile Adhesive) to approx. 6.5 liters. To 7.5 liters. Of cool and clean tap water and stir properly for 5 minute by hand or an electric stirrer to get a smooth and homogeneous mixture.
• After stirring wait for 10 minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive notch trowel
• Press the tiles within 15 to 20 minutes with a shuffling movement in to the adhesive. Check regularly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints
• The proper preparation of the surface will make the fixing easier and quicker ensuring a better finish. The surface should be flat with a tolerance of 4mm over a distance of 2 meters. It is essential to waterproof wet areas prior to tiling
• New concrete is recommended to be 1 month old for every 25mm thickness and completely dried before tiling.
• Under normal circumstances, i.e. a temperature of 20C and a relative humidity of 65%, the joints may be filled after minimum 24 hours.

• 25 kg bag and Project Packing of 40 kg bag is available on demand

• Available in Grey & White

• Factory sealed bags are best before 12 months from the date of manufacturingin unopened condition stored in dry area