The Veebee consistometer measures the remolding ability of concrete under vibration. The test results reflect the amount of energy required to remold a quantity of concrete under given vibration conditions. The Veebee consistometer is applicable to concrete with slumps less than 2 inches. The apparatus, consists of a metal cylindrical container mounted on a vibrating table, which produces a sinusoidal vibration, a slump cone is placed in the center of the cylinder and filled in the same manner as in the standard slump test.

SPECIFICATION : 80C31 / 80C51 / 80C51 Micro controller operating at 10MHZ 32KB powerful software monitor 256 bytes on chip RAM ( partially used by Firmware) Two 16 bit Programmable Timer 32 Programmable I/O pins (24 from 8255 and 6 ( P1.0 to P 1.5) from Port 1 of 8051) 50 Pin FRC connector for system bus expansion 2@26 pin FRC connector for user interface from 8255 9 pin D type connector for RS 232C interface Built in Power supply Six different selectable baud rates from 150 to 9600 One timer and external interrupt 101 Pc type keyboard for entering user address / data and for commands Built in line by line assembler ad disassembler User - friendly software monitor for loading and executing programs with break point facility Facility to connect to PC

• Brand NameMean Well
• Rated Power (Watts)18.9-25.2 W
• Current LevelCurrent level selectable via DIP switch
• Frequency Range47 ~ 63 Hz
• Model NoLCM-25DA
• Open circuit voltage maximum59 V

• Display16 X 2 LCD Display Interface
• Keyboard4 X 4 Matrix Keyboard Interface
• Clock Frequency11.0592 MHz
• Memory TypeFlash Program Memory with ISP and IAP capability
• No of Data SwitchesEight

• UsageLaboratory and Industrial
• Power Supply (V)220 V
• Power consumption3.6 Watts (Approx)
• Fuse1.5 amps
• Frequency50 Hz

Components  Cooling Fan --------------------------------------------1 Detector Mount --------------------------------_----- 1 D.R.F. Meter-------------------------------------------- 1 Gunn Oscillator --------------------------------------- 1 Isolator ------------------------------------------------ 1 Liquid Dielectric Cell --------------------------------- 1 Phase Shifter ----------------------------------------- 1 Pin Modulator ---------------------------------------- 1 Precision Short ---------------------------------------1 Slotted Section ---------------------------------------1 Solid Dielectric Cell----------------------------------- 1 Tunable Probe --------------------------------------- -1 Variable Attenuator 20 dB --------------------------1 W/G Cavity Resonator------------------------------- 1 Wave Guide Stand ------------------------------------3

SPECIFICATION : 80C31 / 80C51 / 80C51 Micro controller operating at 10MHZ 32KB powerful software monitor 256 bytes on chip RAM ( partially used by Firmware) Two 16 bit Programmable Timer 32 Programmable I/O pins (24 from 8255 and 6 ( P1.0 to P 1.5) from Port 1 of 8051) 50 Pin FRC connector for system bus expansion 2@26 pin FRC connector for user interface from 8255 9 pin D type connector for RS 232C interface Built in Power supply Six different selectable baud rates from 150 to 9600 One timer and external interrupt 101 Pc type keyboard for entering user address / data and for commands Built in line by line assembler ad disassembler User - friendly software monitor for loading and executing programs with break point facility Facility to connect to PC

• UsageLaboratory and Industrial
• Power Supply (V)220 V
• Power consumption3.6 Watts (Approx)
• Fuse1.5 amps
• Frequency50 Hz

The Veebee consistometer measures the remolding ability of concrete under vibration. The test results reflect the amount of energy required to remold a quantity of concrete under given vibration conditions. The Veebee consistometer is applicable to concrete with slumps less than 2 inches. The apparatus, consists of a metal cylindrical container mounted on a vibrating table, which produces a sinusoidal vibration, a slump cone is placed in the center of the cylinder and filled in the same manner as in the standard slump test.

Universal Process Control Trainer Code resembles a typical small industrial process plant with different processes and parameters. The plant is controlled using DCS control (Hybrid controller) with SCADA software for supervisory control systems. A jack plug and socket patch board provided at the interface of the process facilitates configuration of different experiments and allows user to develop and test own control strategies. The patch board also allows direct access to transmitters and control elements enabling user to connect external controllers, PLCs & DCSs. The product layout is designed to educate, train and develop the user to cover various aspects of process control. User can configure the product from study of basic components to advanced study of complex process control loops using advanced DCS control.

• Brand NameMean Well
• Rated Power (Watts)18.9-25.2 W
• Current LevelCurrent level selectable via DIP switch
• Frequency Range47 ~ 63 Hz
• Model NoLCM-25DA
• Open circuit voltage maximum59 V

Components  Cooling Fan --------------------------------------------1 Detector Mount --------------------------------_----- 1 D.R.F. Meter-------------------------------------------- 1 Gunn Oscillator --------------------------------------- 1 Isolator ------------------------------------------------ 1 Liquid Dielectric Cell --------------------------------- 1 Phase Shifter ----------------------------------------- 1 Pin Modulator ---------------------------------------- 1 Precision Short ---------------------------------------1 Slotted Section ---------------------------------------1 Solid Dielectric Cell----------------------------------- 1 Tunable Probe --------------------------------------- -1 Variable Attenuator 20 dB --------------------------1 W/G Cavity Resonator------------------------------- 1 Wave Guide Stand ------------------------------------3