Oil Bath, is a type of heated bath which uses boiling oil as the temperature regulator. Since different oils have different boiling points it is possible to obtain a temperature near to the desired temperature by selecting an oil with a boiling point as close as possible to the desired temperature. The most common oils that are being utilized in oil baths are paraffin, glycerol, silicon oil or cottonseed oil due to their quite odorless characteristics.

Double Walled High Temperature Oil Bath is having wide range of application, such as oxidation stability test on oils, greases, etc, or any other test requiring high temperature control having high thermal efficiency. This oil bath was developed for a wide range of testing and meets ASTM specifications for Methods D471, D865, and D1313.

• Interior construction of stainless steel 304
• Outer construction-PCRC sheet /SS 304 (as per requirement)
• 75mm glass wool insulated on five sides
• Provided with High speed stirrer with speed regulator
• Control panel provided on the side of oil bath two neon lights and an ON/OFF switch.
• Perforated and removable diffuser shelves
• Microprocessor based temperature controller
• Aesthetically designed-Designed according to the standards and principles underlining industrys aesthetic values.
• Corrosion Resistant interior and exteriors-Corrosion resistant coatings like epoxy coatings are applied inside and outside the baths to prevent against degradation due to moisture, salt spray, oxidation or exposure to a variety of environmental or industrial chemicals/ corrosive agents.
• Energy Efficient the baths uses less energy to provide the same level of performance, comfort and convenience, thus making it energy conserving.
• Sturdy Construction the baths are built with robustness to withstand stress and strain, giving it long life and ability to perform in extreme stress environments.

A water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. WEIBER water baths are widely used for day to day bacteriological and varied laboratory applications requiring incubation as well as general tests and procedures in variety of research and testing laboratories.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

• Versatile usage
• Ergonomic Design
• Energy Efficient
• Long life
• Low Maintenance
• Calibration And Protocol Documentation
• PID temperature controller

Mash Bath are designed for laboratory use in breweries and malt houses. It aids in the determination of malt extract. The equipment allows one to utilize the CONGRESS, HARTONG 20, HARTONG 45, HARTONG 65, HARTONG 80, ASBC, PROFILE or THERMOSTAT methodology of testing. The Thermostat method maintains a constant temperature for a specific time. The Profile method allows the user to program the variables to suite their needs.

• Programmable delayed start
• Audible alarm
• Low level water cut out
• Accurate water dispense (+/- 5ml) to all beakers in less than 2 min
• RS 232/485 interface (optional)
• Timer (optional)
• Real time data acquisition system (optional)
• USB ports (optional)
• Printer report program (optional)

Calibration temperature baths provide optimal temperature environments for secondary or comparison temperature calibrations. They offer unsurpassed stability and uniformity, a large working volume, and flexibility for performing thermometer calibration on calibrating a variety of temperature sensors. It not only allows calibration of multiple systems at the same time, but also offer the added advantage of accommodating sensors of all shapes and sizes.These high temperature baths provide calibration temperature upto300C.

Calibration baths are stable to 0.001 C and do not require calibration blocks or use of special calibration techniques to achieve that stability. Standard as well as customized models are available.

• Large-capacity tanks for higher productivity
• Calibrations up to 300 C
• Built-in cooling coils for faster cooling
• The units are operated via an innovative and user friendly control panel which includes an LCD display, and offer configurable PID controller (HMI+PLC as an option)
• Visual and audible alarms in the event of a failure
• Dual protection system against uncontrolled over-temperature events:
• Heating elements turn off automatically if measured temperature exceeds the set threshold by 5C
• Mechanical over-temperature device shuts off heating elements if temperature exceeds maximum allowed values

Carlsberg flasks are used for yeast propagation. WEIBER Carlsberg flask test bath are designed specificallyfor its testing with full range of features and support. These are extremely used in beer industry and itssubsidiary test laboratories.

• Splash-proof key pad with integrated mains switch
• Felling level indicator
• Powerful immersion pumps, suitable for continuous operation
• Easy filling form the top with hinged protective lid
• Low liquid level protection with optical and audible alarm signal
• Removable venting grid for cleaning of the condenser
• Low Liquid Level Protection
• RS232 interface for PC-connection (Optional)
• Calibration And Protocol Documentation
• Air cooled refrigeration unit
• CFC free refrigerant

Water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. Circulating water baths (also called stirrers ) are ideal for applications when temperature uniformity and consistency are critical, such as enzymatic and serologic experiments. Water is thoroughly circulated throughout the bath resulting in a more uniform temperature.

We specialize in both standard and customized circulatory water bath equipments, specifically designed to meet the challenging demands of various research applications.

Serological water baths are used for clinical procedure, Incubation, Inactivation, Agglutination, as well as most serological pharmaceutical, biomedical procedure, Washerman, Kolmer and Khan Test inactivation's, Paraffin Embedding and many other applications in the laboratories.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

Refrigerated baths offer a completely integrated refrigerated circulating system for open or closed applications, with a temperature range from -35C to +100C. Our refrigerated water baths are widely used for day to day bacteriological and varied laboratory applications requiring incubation as well as general tests and procedures in variety of research and testing laboratories including Wassermann, Kilmer tests. Apart from that, these refrigerated water baths have a variety of usages in tissue culture applications, enzyme reaction studies, growth observation studies, fermentation analysis and various other general and specialized applications in various laboratories.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

Pycnometer is a device used to calculate density of a semi solid or liquid. WEIBER pycnometer test baths are specifically designed for incubating pycnometers bottles upto 2000ml.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

Nitrogen evaporators (water bath type) are typically used to concentrate samples before analysis or to concentrate samples before a solvent exchange.When a scientist needs to concentrate a sample thats in a volatile liquidlike acetone, acetonitrile, or methanola nitrogen evaporator can do the job. As a result, scientists use this technology in sample preparation in environmental, polymer science, quality control, and toxicology labs etc.Our nitrogen evaporators utilize adjustable nitrogen blow down technology allowing full control of nitrogen flow to samples, with no wasted nitrogen gas. We combined this technology with uniform efficient heat applied through water baths. This simultaneously maximizes solvent evaporation in the samples being concentrated and saves the lab money.

The 24 position WEIBER nitrogen evaporator is our most adaptable version but we can customize it to 6/12/34/50 positions as per the requirement.

• Microprocessor based control system.
• Can accommodate samples with an outside diameter of 10-30 mm.
• Provides controlled concentration of sample vials through the application of nitrogen gas within a heated water bath.
• The dual band spring hoist assembly provides a simple and effective means of removing samples from the heated water bath.
• Circular rotating design permits each sample to be accessible from the front of the instrument for easy insertion and retrieval.
• The chrome plated needle valves are individually milled from solid brass, enabling precise, uniform adjustments for your nitrogen blow down.
• Efficient and safe sample reduction with minimal nitrogen waste.
• Long lasting and user friendly technology
• Gas flow can be controlled at each sample position via needle valves
• Nitrogen filter
• High pressure phthalate free tubing for safety, Teflon tubing for no contamination
• Needles, 4 inch x 19 gauge with polypropylene hub and stainless steel shaft
• 220v wiring harness (optional)
• Z-Purge/intrinsically safe purge case (optional)
• Acid resistant coating on instrument and needles (optional)
• Side control box with built-in digital controller, timer, and pressure regulator (optional)

A water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. WEIBER reciprocating shaking water bath has an extra control for shaking, which moves liquids around. Shaking feature can be turned on or off. It is designed for a wide range of temperature-controlled shaking protocols, such as Northern and Southern Hybridization, Destaining of gels, Incubation of cells or bacterial cultures as well as Wash Processes. The temperature range, which goes up to 99C also allows you to use the bath as a Boiling Bath.

The Shaking Water Bath is equipped with a PID Controller for easy temperature selection, rapid heat up and excellent stability. A high quality, robust design with a unique shaking mechanism that allows you to easily switch from orbital mode to reciprocating mode by simply reversing the tray.

Oil Bath, is a type of heated bath which uses boiling oil as the temperature regulator. Since different oils have different boiling points it is possible to obtain a temperature near to the desired temperature by selecting an oil with a boiling point as close as possible to the desired temperature. The most common oils that are being utilized in oil baths are paraffin, glycerol, silicon oil or cottonseed oil due to their quite odorless characteristics.

Double Walled High Temperature Oil Bath is having wide range of application, such as oxidation stability test on oils, greases, etc, or any other test requiring high temperature control having high thermal efficiency. This oil bath was developed for a wide range of testing and meets ASTM specifications for Methods D471, D865, and D1313.

• Interior construction of stainless steel 304
• Outer construction-PCRC sheet /SS 304 (as per requirement)
• 75mm glass wool insulated on five sides
• Provided with High speed stirrer with speed regulator
• Control panel provided on the side of oil bath two neon lights and an ON/OFF switch.
• Perforated and removable diffuser shelves
• Microprocessor based temperature controller
• Aesthetically designed-Designed according to the standards and principles underlining industrys aesthetic values.
• Corrosion Resistant interior and exteriors-Corrosion resistant coatings like epoxy coatings are applied inside and outside the baths to prevent against degradation due to moisture, salt spray, oxidation or exposure to a variety of environmental or industrial chemicals/ corrosive agents.
• Energy Efficient the baths uses less energy to provide the same level of performance, comfort and convenience, thus making it energy conserving.
• Sturdy Construction the baths are built with robustness to withstand stress and strain, giving it long life and ability to perform in extreme stress environments.

A water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. WEIBER water baths are widely used for day to day bacteriological and varied laboratory applications requiring incubation as well as general tests and procedures in variety of research and testing laboratories.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

• Versatile usage
• Ergonomic Design
• Energy Efficient
• Long life
• Low Maintenance
• Calibration And Protocol Documentation
• PID temperature controller

Mash Bath are designed for laboratory use in breweries and malt houses. It aids in the determination of malt extract. The equipment allows one to utilize the CONGRESS, HARTONG 20, HARTONG 45, HARTONG 65, HARTONG 80, ASBC, PROFILE or THERMOSTAT methodology of testing. The Thermostat method maintains a constant temperature for a specific time. The Profile method allows the user to program the variables to suite their needs.

• Programmable delayed start
• Audible alarm
• Low level water cut out
• Accurate water dispense (+/- 5ml) to all beakers in less than 2 min
• RS 232/485 interface (optional)
• Timer (optional)
• Real time data acquisition system (optional)
• USB ports (optional)
• Printer report program (optional)

Calibration temperature baths provide optimal temperature environments for secondary or comparison temperature calibrations. They offer unsurpassed stability and uniformity, a large working volume, and flexibility for performing thermometer calibration on calibrating a variety of temperature sensors. It not only allows calibration of multiple systems at the same time, but also offer the added advantage of accommodating sensors of all shapes and sizes.These high temperature baths provide calibration temperature upto300C.

Calibration baths are stable to 0.001 C and do not require calibration blocks or use of special calibration techniques to achieve that stability. Standard as well as customized models are available.

• Large-capacity tanks for higher productivity
• Calibrations up to 300 C
• Built-in cooling coils for faster cooling
• The units are operated via an innovative and user friendly control panel which includes an LCD display, and offer configurable PID controller (HMI+PLC as an option)
• Visual and audible alarms in the event of a failure
• Dual protection system against uncontrolled over-temperature events:
• Heating elements turn off automatically if measured temperature exceeds the set threshold by 5C
• Mechanical over-temperature device shuts off heating elements if temperature exceeds maximum allowed values

Carlsberg flasks are used for yeast propagation. WEIBER Carlsberg flask test bath are designed specificallyfor its testing with full range of features and support. These are extremely used in beer industry and itssubsidiary test laboratories.

• Splash-proof key pad with integrated mains switch
• Felling level indicator
• Powerful immersion pumps, suitable for continuous operation
• Easy filling form the top with hinged protective lid
• Low liquid level protection with optical and audible alarm signal
• Removable venting grid for cleaning of the condenser
• Low Liquid Level Protection
• RS232 interface for PC-connection (Optional)
• Calibration And Protocol Documentation
• Air cooled refrigeration unit
• CFC free refrigerant

Water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. Circulating water baths (also called stirrers ) are ideal for applications when temperature uniformity and consistency are critical, such as enzymatic and serologic experiments. Water is thoroughly circulated throughout the bath resulting in a more uniform temperature.

We specialize in both standard and customized circulatory water bath equipments, specifically designed to meet the challenging demands of various research applications.

Serological water baths are used for clinical procedure, Incubation, Inactivation, Agglutination, as well as most serological pharmaceutical, biomedical procedure, Washerman, Kolmer and Khan Test inactivation's, Paraffin Embedding and many other applications in the laboratories.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

Refrigerated baths offer a completely integrated refrigerated circulating system for open or closed applications, with a temperature range from -35C to +100C. Our refrigerated water baths are widely used for day to day bacteriological and varied laboratory applications requiring incubation as well as general tests and procedures in variety of research and testing laboratories including Wassermann, Kilmer tests. Apart from that, these refrigerated water baths have a variety of usages in tissue culture applications, enzyme reaction studies, growth observation studies, fermentation analysis and various other general and specialized applications in various laboratories.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

Pycnometer is a device used to calculate density of a semi solid or liquid. WEIBER pycnometer test baths are specifically designed for incubating pycnometers bottles upto 2000ml.

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

Nitrogen evaporators (water bath type) are typically used to concentrate samples before analysis or to concentrate samples before a solvent exchange.When a scientist needs to concentrate a sample thats in a volatile liquidlike acetone, acetonitrile, or methanola nitrogen evaporator can do the job. As a result, scientists use this technology in sample preparation in environmental, polymer science, quality control, and toxicology labs etc.Our nitrogen evaporators utilize adjustable nitrogen blow down technology allowing full control of nitrogen flow to samples, with no wasted nitrogen gas. We combined this technology with uniform efficient heat applied through water baths. This simultaneously maximizes solvent evaporation in the samples being concentrated and saves the lab money.

The 24 position WEIBER nitrogen evaporator is our most adaptable version but we can customize it to 6/12/34/50 positions as per the requirement.

• Microprocessor based control system.
• Can accommodate samples with an outside diameter of 10-30 mm.
• Provides controlled concentration of sample vials through the application of nitrogen gas within a heated water bath.
• The dual band spring hoist assembly provides a simple and effective means of removing samples from the heated water bath.
• Circular rotating design permits each sample to be accessible from the front of the instrument for easy insertion and retrieval.
• The chrome plated needle valves are individually milled from solid brass, enabling precise, uniform adjustments for your nitrogen blow down.
• Efficient and safe sample reduction with minimal nitrogen waste.
• Long lasting and user friendly technology
• Gas flow can be controlled at each sample position via needle valves
• Nitrogen filter
• High pressure phthalate free tubing for safety, Teflon tubing for no contamination
• Needles, 4 inch x 19 gauge with polypropylene hub and stainless steel shaft
• 220v wiring harness (optional)
• Z-Purge/intrinsically safe purge case (optional)
• Acid resistant coating on instrument and needles (optional)
• Side control box with built-in digital controller, timer, and pressure regulator (optional)

A water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. WEIBER reciprocating shaking water bath has an extra control for shaking, which moves liquids around. Shaking feature can be turned on or off. It is designed for a wide range of temperature-controlled shaking protocols, such as Northern and Southern Hybridization, Destaining of gels, Incubation of cells or bacterial cultures as well as Wash Processes. The temperature range, which goes up to 99C also allows you to use the bath as a Boiling Bath.

The Shaking Water Bath is equipped with a PID Controller for easy temperature selection, rapid heat up and excellent stability. A high quality, robust design with a unique shaking mechanism that allows you to easily switch from orbital mode to reciprocating mode by simply reversing the tray.