Mumbai, Maharashtra, India
GST : 27ACUPC0475F1ZK
Verified
Add Review
Our Product / Services
Applications:
Heat Treatment:
Welding:-If welding is necessary pre-heat at 250°C and follow welding with a full anneal. Grade 420 filler will give a high hardness weld (although not as high as the 440C), but 309 or 310 will produce soft welds with higher ductility.
Composition
| Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N | |
| 440C | min. max. | 0.95 1.20 | -1 | -1 | -0.04 | -0.03 | 16.00 18.00 | -0.75 | - | - |
Mechanical Properties
| Tempering Temperature (°C) | Tensile Strength (MPa) | Yield Strength 0.2% Proof (MPa) | Elongation (% in 50mm) | Hardness Rockwell (HR C) | Impact Charpy V (J) |
| Annealed* | 758 | 448 | 14 | 269HB max# | - |
| 204 | 2030 | 1900 | 4 | 59 | 9 |
| 260 | 1960 | 1830 | 4 | 57 | 9 |
| 316 | 1860 | 1740 | 4 | 56 | 9 |
| 371 | 1790 | 1660 | 4 | 56 | 9 |
| * Annealed properties are typical for Condition A of ASTM A276# Brinell Hardness is ASTM A276 specified maximum for annealed 440A, B and C. | |||||
Physical Properties
| Grade | Density (kg/m3) | Elastic Modulus (GPa) | Mean Coefficient of Thermal Expansion (mm/m/°C) | Thermal Conductivity(W/m.K) | Specific Heat 0-100°C (J/kg.K) |
Electrical Resistivity (nW.m) | |||
| 0-100°C | 0-200°C | 0-600°C | at 100°C | at 500°C | |||||
| 440 C | 7650 | 200 | 10.1 | 10.3 | 11.7 | 24.2 | - | 460 | 600 |
Alternative Grades
| Grade | Why it might be chosen instead of 440C |
| 440A/B | Slightly softer and more corrosion resistant grade needed |
| 440F | High machinability required, with same hardness and hardenability as 440C |
| 420 | Lower strength and hardness needed than any of the 440 Grades |
| 416 | Higher machinability required, and the much lower hardness and strength is still adequate |
Duplex Steel S31803/32205 combines improved resistance to stress corrosion cracking, pitting, crevice corrosion and high strength. Due to it's chemical composition F51 duplex stainless steel resists chloride environments and sulphide stress corrosion.
Availability Duplex Steel S31803/32205 is available in Plate, Sheet, Round Bar, Flat Bar and Forging Stock for sizes contact us.
Specifications
Duplex Steel S31803/32205 (F51/WS 1.4462) / (F60/WS 1.4470)
| Grade | US Aerospace/Military | US Commercial | British Specification | European Specification | Other |
|---|---|---|---|---|---|
| Duplex S31803/32205 | ASTM A182 F51 / F60 ASTM A276 F51 / F60 ASTM A479 F51, AISI F51 |
BS 318S13 (Wrought) BS 332C15 (Cast) |
WS 1.4462 WS 1.4470 X2CrNiMoN22.5.3 AFNOR Z2CND22.05Az |
UNS S31803 UNS S32205 SAF2205 - SANMAC URANUS 45N, FALC223 |
Technical Data Sheet
| Weight % | C | Mn | P | S | Si | Cr | Ni | Mo | N |
|---|---|---|---|---|---|---|---|---|---|
| Duplex F51 | 0.03 max | 2.0 max | 0.03 max | 0.02 max | 1 max | 21-23 | 4.5-6.5 | 2.5-3.5 | 0.80-0.20 |
Typical Mechanical Properties
| Alloy | Tensile Strength N/mm² | Proof Strength 0.2% N/mm² | Elongation (%) | Hardness Brinell |
|---|---|---|---|---|
| F51 | 105 | 55 | 35 | 170-255 |
| F51 | 95 | 50 | 35 | 170-255 |
Plug Valves are available in three different types versions:
Special Design Features :
We are service providers of fabrication services.Harsh steel - specialist fabrications of exotic materials for the offshore industry as per customer reqirements.Harsh steel is a specialised exotic nickel alloys such as inconel, monel, hastelloy, stainless steel, titanium, tantalum metals fabricator for the offshore and petrochemical, pharma, oil and gas industries. The company does the job on outsourced basis with its technique of supplying or importing raw materials and finalising the components with cheaper costs in addition to our fabrication service we offer a full subcontract design and drawing package. The company has an ongoing commitment to maintain and improve the high quality and standards required by our offshore and petrochemical customers.
Our extensive understanding of the exacting standards required by the offshore industry enables us to provide you with an excellent service. We pride ourselves on our ability to meet these exacting standards and the often short delivery requirements of the marketplace.
Types of specialist metals for which harsh steel provides customised fabricationharsh steel is able to offer fabrication and welding services for the following materials: titanium, hastelloy alloys, inconel alloys, incoloy, zeron 100, super duplex, duplex, stainless steel - 316l and 304l, 6mo, cupro nickel, monel etc.
Types of nickel alloys and titanium fabricated productsharsh steel from past 20 years supplying raw materials to various fabrication companies, so it planned to do the fabrication with its own outsourced services. Our highly skilled project and production team has a wealth of experience in dealing with complex and difficult fabrication issues, and we pride ourselves on our can-do attitude and solutions-driven approach to sometimes complex fabrications.
We have outsourced and manufacturedpressure vesselsshell and tube heat exchangersturbine shaft assemblyfilterssheet metal componentsnozzles and ferrule fittingsvalvesvesselspipe work and fittings along with u pipesheating pipes
Stainless steel annular corrugated metallic flexible hoses are manufacturing in austantic steel ANSI 321, 316, 316L & 304 grades conforming to BS 6501, Part-1 : 2004 / ISO 10380 : 2003. The annular corrugated metallic hose body provided the flexibility and pressure tight core of the assembly. We also manufacture highly flexible close –pitch hoses for special applications. Stainless steel annular corrugated metallic flexible hose are offered from Size : 1/4"(DN 6) to 12"(DN 300).
Harsh Steel is manufacturing jacketed flexible hose assemblies. The Inner annular corrugated stainless steel flexible metallic hose conveys the fluid and jackets annular corrugated stainless steel flexible metallic hose for heating or coolant fluid or protective the hose and both Inner and jacketed hoses are highly flexible.
We are using our annular corrugated stainless steel flexible metallic hoses ANSI 321 / 316L with ANSI 304 single wire braiding. We will provide both the end flange fittings swivel or fixed type and for inlet & outlet heating or cooling fluid end connection we will provide flange end or threaded end at an offset angle of 180°, Hoses conform to BS 6501, Part-1:2004 / ISO 10380:2003.
Advantages of Flexible Metal Hose :
Types of Nitinol bars we stock:
Application of Nitinol round bars:Nitinol round bars used for many different medical and industrial applications.
Harsh Steel is known for providing its customers Inconel Alloy 718 Forged Components that they can afford and use effectively. Inconel alloys are available in a wide range of shapes. Harsh Steel also offers forging services that include creating custom designs from raw materials. Inconel alloy 718 is a high-strength, corrosion-resistant nickel chromium material used at -423o to 1300oF. The age-hardenable alloy can be readily fabricated, even into complex parts. Its welding characteristics, especially its resistance to post weld cracking, are outstanding. The ease and economy with which Inconel Alloy 718 can be fabricated combined with good tensile, fatigue, creep and rupture strength, have resulted in its use in a wide range of applications. Examples of these Forged Components are liquid fueled rockets, rings, casings and various formed sheet metal parts for aircraft and land-based gas turbine engines and cryogenic tank age. It is also used for fasteners and instrumentation parts.
More about Inconel Alloy 718 Forged Components :Inconel alloy 718, W.NR 2.4668, UNS N07718 is available at harsh steel in forms of Inconel alloy 718 Sheets, Inconel alloy 718 Strips, Inconel alloy 718 Round bars, Inconel alloy 718 Seamless and welded pipes and tubes. Inconel alloy 718 is supplied as per AMS 5663, AMS 5832, AMS 5962, and AMS 5662, ASTM B637 standards. Inconel alloy 718 is a Nickel and Chromium alloy which is precipitation hardenable and high temperatures to about 700°C (1290°F). It has higher strength than Inconel X-750 and better mechanical properties at lower temperatures than Nimonic 90 and Inconel X-750.
Inconel alloy 718 Strips, Sheets and round bars Chemical composition :
Because of excellent corrosion resistant characteristics in the presence of salt water, acids, alkaline (bases) and a variety of other caustic media, Monel Alloy 500 Forgings are often used in marine applications or chemical processing operations. Monel Alloy 500 can be forged into propeller shafts for various types of watercraft as well as seawater pump shafts and impellers. Products forged from Monel Alloy 500 are found in the storage, transport and processing equipment for organic acids as well as dry or caustic chloride. Monel Alloy 500 Forgings are often found in marine applications as pipes, valves, pump shafts, fittings, and fasteners, or as heat exchangers for the power generation industry as well as other industries. They are especially valuable for the processing of chemicals and hydrocarbons.
Range of Monel Alloy 500 Forged High Pressure Fittings Comprises :Nipples, Couplings, Weldolets, Caps, Elbows 45o or 90o, Tees -Equal or reducing, Plugs – Hexagonal, Square or Round Head, Bushing, Unions, Rings, Discs / Circles, Hollow Shaft, Square Bars, Rectangular Bars and Custom Forgings.
Size of Pressure Monel Alloy 500 Fittings : 1 / 8″up to 6″
Specifications:
Harsh steel stocks a wide range of stainless steel coils and sheets in both large and small quantities according to ASTM standards. If you are looking for special sizes of stainless steel slitting coils in India and Export purpose Harsh steel is the provider with the relationship with domestic and international Mills. We can supply your organisation with competitive price, special sizes of stainless steel coils and slitting coils with the best of Quality and Mill test certificates in Ready stock delivery.
STAINLESS STEEL COIL APPLICATIONS:
Harsh steel Supplies and offers a diverse range of Stainless Steel Plate, Sheet and Coil. The most common grades of Stainless Steel Sheets that we offer are 3CR12, 430, 304 and 316, 409, 410, 444, 309, 310s, 321, 347, 321, 904L, 2205, 2304, 316Ti, 316H, 317L are all available on request. Stainless Steel sheets and plates, also commonly known as Cold Rolled products, are available in the following finishes: 2B, No.4 with PVC and BA with PVC and all decorative and designer stainless steel sheets are available at Harsh steel on request. Stainless Steel Sheets Standard lengths (in mm) are: 2000, 2500, 3000 and 6000. Standard widths (in mm) are 1000, 1250 and 1500. All material is produced to the following international specifications: tolerance to ASTM A480m, chemical to ASTM A240 91A, mechanical to ASTM A240 91 and Harsh steel provides stainless steel plates with Mill test Certificate or Third party inspection certified material only.
| Thickness Range of Stainless Plate | 3/16″ Thru 6″ Thick Stainless Steel Plate |
|---|---|
| Common Widths of Stainless Plate Coil | 48″ Wide – 60″ Wide – 72″ Wide – 78.75″ (2 Meter) wide – 84″ wide – 96″ wide – 120″ wide & other widths upon customer request. |
| 200-300 Series Stainless Steel Grades | 202- 301 – 304 – 304L – 304L Polished – 304H – 309 – 309S – 309H – 310 – 310S – 310H – 316L – 316L Polished – 317L – 317LMN – 321 – 321H – 330 – 347 347H |
| 400 Series Stainless Steel Grades | 405 – 410 – 410S – 416 – 420 – 440C |
| Duplex Stainless Steel Grades | LDX 2101 – Duplex 2205 – Duplex 2507 |
| Precipitation Hardening Grades | 17-4PH – 17-4 H1150 (per customer request) – 15-5PH |
| Nickel Alloy Grades | Alloy 20 – Alloy 200 – Alloy 400 – Alloy 600 – Alloy 800 – Alloy 800HT – Alloy C-276 (nickel grades may require lead time) |
Harsh Steel is a leading manufacturer of Stainless Steel forged discs, Stainless Steel finished machined tube sheets, Stainless Steel seamless rolled rings, Stainless Steel flanges, Stainless Steel nozzles, Stainless Steel forged pipes or complete packages starting from 2" WN flange to a 30 tons tube sheet, we can provide a cost-effective, timely, Stainless Steel forging solution. Material grades such as 304/304L and 316/316L/316TI, 409, 410, , 430, 309, 310s, 321, 347, 321, 904L, 2205, 2304, 316Ti, 316H, 317L. Alloy 20, Alloy 330, Alloy 286 and all Duplex Stainless steel grades and Super Duplex grades along with Nickel alloy and Titanium. Forging shapes include Stainless Steel forged discs, Stainless Steel forged hubs, Stainless Steel forged blocks, Stainless Steel forged shafts (including step shafts or with flanges), Stainless Steel forged sleeves, Stainless Steel forged cylinders, Stainless forged Steel flats, Stainless Steel forged hexes, Stainless Steel forged rounds, Stainless Steel forged plate, and some Stainless Steel forged custom shapes. Stainless Steel Forgings can be produced as finished size, finished size rough machined, forged size, forged size rough machined, as forged size, or as forged size with allowance to finish to your finish size print. Seamless rolled rings and contoured rings are produced to save on material, machining costs and transportation costs.
Types of Forged Stainless Steel products Harsh Steel Manufacturers is as followsStainless Steel Forgings for heat exchanger, boiler and pressure vessel manufacturing Tube sheets, nozzles, girth flanges and rings, LWN Flanges, forged nozzle flanges, orifice and special flanges
1. Type of Stainless steel , Nickel alloy Forged flanges Manufactured by Harsh Steel :For the manufacturing of ball valves, well head equipment, gate valves and other equipment we can supply pieces according to your drawings. We also supply forged idlers and rollers to manufacturers of mining trucks, hydraulic excavators, crawler loaders and similar machines along with Stainless steel Forged Round bars, Stainless steel blocks, Stainless steel forged plates; Stainless steel Hex bars, Stainless steel patta, Stainless steel forges sleeves and Stainless steel connectors.
Stainless steel Forged pipes, Stainless steel cylinder bodies and bushings, Stainless steel Forged vessel shells, Stainless Steel Hot formed dish heads
We supply a wide range of forged shafts and rounds bars for offshore, oil and gas, sugar mills, cement mills, steel mills, mining equipment and other heavy machinery in Material grades such as 304/304L and 316/316L/316TI, 409, 410, , 430, 309, 310s, 321, 347, 321, 904L, 2205, 2304, 316Ti, 316H, 317L. Alloy 20, Alloy 330, Alloy 286 and all Duplex Stainless steel grades and Super Duplex grades along with Nickel alloy and Titanium
Forged stepped shaft with diameters of over 1500mm and 40 tons of weight.Forged spindles pump shafts, generator shafts, Shafts for steam- and gas turbines.
6. Stainless Steel Forged fittings, Stainless Steel Forged tubes and pipes, Stainless Steel Forged Elbows, Stainless Steel Forged tees, Stainless Steel Forged reducers, Stainless Steel Forged caps and Stainless Steel Forged stub ends, Stainless Steel Forged NozzleForged fittings Long radius induction bends.All fittings and pipes can be supplied with weld overlay inclusive Titanium, according to Clinets specifications.
7. Stainless Steel Forged Heat exchanger and boiler tubes & Stainless Steel Forged ERW Pipes, LSAW and SSAW PipesHarsh Steel uses high quality raw material which is guaranteed and proved by raw material certificate with each delivery.
Other Stainless Steel Forged Products available at Harsh Steel:Starting from carbon steel forging materials like A105, A266 and A350 LF2 for low temperature service up to demanding materials such as A182 F51, F6NM (1.4313), F44 / 254 SMO, Super duplex F53 or A182/A336 F91 Harsh steel is master in covering requirement as per clients drawings. Full series of stainless steels including A182 F317L /347, 316Ti as well as 904L forgings are available. Titanium forgings of 3 tons and more in B381 F1, F2, F3, and F12 can be supplied. Cu-Ni 70/30 & Cu-Ni 90/10 and other non-ferrous material are available.
| PLAIN AND STEPPEN SHAFTS : | OD: 50-350 mm Length - 3000 mm max. |
|---|---|
| FLATS: | OD: 10-300 mm. Width - 30-650mm Length - 3000 mm |
| BLANKS: | OD: 1100mm, Th-20-500mm. |
| RINGS : | OD : 100-2000 mm, ID -80-1900mmTH -25-900mm |
| RODS : | OD: 5-600 mm, Length -100-3000 mm |
| SHAPED ITEMS: | AS PER CLIENTS REQUIREMENTS |
| WE ARE SPECIALISED IN FORGING OF CUSTOMISED SHAPES AND SIZES AS PER CUSTOMER REQUIREMENTS AND DRAWINGS IN STAINLESS STEEL, DUPLEX STEEL, CUPRO NICKEL, SUPER DUPLEX STEEL, NICKEL ALLOYS, MONEL ALLOYS, INCONEL ALLOYS, HASTELLOY ALLOYS, ALUMINIUM AIRCRAFT ALLOYS AND TITANIUM ALLOYS | |
| Materials Available | |
| Carbon Steels : | ENS , EN 8, E 19, EN 24, EN 31, EN 36C, EN 353, EN 354 SA105, SA350, LF2, ETC. |
| Stainless Steels, Nickel alloys , Duplex steel and Titanium alloys : | Stainless Steel SS 303, SS 304 & SS 304L, SS 309, SS 310, SS 316L, SS 317L, SS 321, SS 330, SS 347, SS 409, SS 410, SS 420, SS 431, 17-4PH, 13-8MO, 15-5PH, 15-7MO, 254SMO, 2205 Super Duplex etc. Nickel alloy A-286, Alloy 20, Alloy 800, Alloy 718, Alloy 825, Alloy 725, Alloy 738LC, Alloy750, Alloy B2, Alloy 901, Alloy 400, Alloy C, Alloy 925, Alloy 800, Alloy 500 (K), Alloy C276, Alloy 600, Alloy 200, Alloy 601, Alloy 201, Alloy 617, Alloy 625, Alloy X, Alloy 713LC Titanium Alloys Grade 1, Grade 2, Grade 5, Grade 7, Grade 9, Grade 12. |
| Aluminium Alloy: | 1100, 2014, 5083, 5086, 6061, 6351, 7020, 7075 HT Conditions available : WP, T6, T6521 / T 852 / T 735 |
| Copper Alloys : | Cu Ag, Cur Cr, Cu Zn, Etc |
| Other Alloys : | Magnesium, Silver Alloys |
Harsh steel Stocks Stainless steel extruded Angle in all Grades. Stainless Steel Angle is available in many different sizes and thickness', also Angle is available where one side is longer than the other. Angle is typically at 90 degrees. Harsh steel can cut to length, weld, drill or mitre based on your specific requirements. As with all our products these can be picked up directly from our workshop or delivery can be arranged. Angle is commonly used for bracing and brackets where right angles needs to be maintained, they can be fixed together by means of welding, riveting, bonding or with nuts and bolts.
Harsh steel manufactures, supply and export Stainless Steel Pipes in austenitic, duplex and nickel alloy seamless and welded steel pipes both from coil and from plate. During continuous production from coil, in one single operation the base material can be formed into a pipe, welded, heat-treated and subjected to non-destructive testing. All pipes are pickled and passivated in our 13 meter long with outsourced pickling facilities. Stainless Steel and duplex pipes are available in following grades 304/304L and 316/316L/316TI, 409, 410, , 430, 309, 310s, 321, 347, 321, 904L, 2205, 2304, 316Ti, 316H, 317L. Alloy 20, Alloy 330, Alloy 286 and all Duplex Stainless steel grades and Super Duplex grades along with Nickel alloy and Titanium.
Following sizes of stainless steel pipes can be produced in stainless Steel by Harsh Steel:The stainless steel pipes can be manufactured in fixed lengths & random lengths between 4 & 12 meter. Stainless steel Pipes with an outside diameter between 6" (168, 3 mm) and 80" (2032 mm). Harsh steel stocks Stainless steel pipes and standard piping which is ordered in accordance with ASME/ASTM SA/A312 with dimensions and weights in accordance with ASME B36.19. ASME B 36.10 available on request. Lengths of pipe are standard 6 meters. We stock austenitic grades in 304L and 316L. Other grades such as Duplex, High Nickel Alloys, heat resistant stainless steels, 904L can be sourced internationally accordance with the customer requirements. Harsh Steel has its very own large bore pipe plant that can produce piping from 12 inches to 80 inches diameter in full 6 meter lengths to any International Specification or customer requirement. Heat exchanger tubing can be supplied to client's request. Heat exchanger tubing is available at Harsh Steel in Ferritic, Austenitic or Duplex steels. It can be welded or seamless. The most commonly requested specs are ASTM A269, ASTM A268, ASTM A249, and ASTM A213. Harsh Steel Stainless steel pipe sizes vary from 304/L and 316/L pipe in sizes " through 36", in Schedules 05S through 80S and larger. Our tubing inventory consists of 6" and 8" OD tubing with wall thicknesses ranging from .083" to .120". We offer Alloy 317L pipe stocked in sizes 6" through 12", in Schedules 10S and 40S. In addition to all these different sizing offerings, we also have other 300 series grades available from inventory, in case you do not find exactly what you are looking for.
Harsh steel manufactures ERW (Welded) stainless steel pipes and Tubes from single stainless steel plates in the following size range:Harsh steel material range includes high performance austenitic stainless steel, high temperature austenitic stainless steel, duplex & super duplex stainless steel and nickel alloy grades. The pipes can be produced in single random or double random lengths. Furthermore harsh steel has fully automatic welding equipment to make circumferential welds to enable the supply of double random lengths with a maximum length of 12 meter.
Harsh steel manufactures welded austenitic, duplex and nickel alloy welded stainless steel pipes in accordance with:
Harsh steel manufactures, supply and export Stainless Steel Tubes in austenitic, duplex and nickel alloy seamless and welded steel tubes both from coil and from plate. During continuous production from coil, in one single operation the base material can be formed into a tube, welded, heat-treated and subjected to non-destructive testing. All tubes are pickled and passivated in our 13 meter long with outsourced pickling facilities. Stainless Steel and duplex tubes are available in following grades 304/304L and 316/316L/316TI, 409, 410, , 430, 309, 310s, 321, 347, 321, 904L, 2205, 2304, 316Ti, 316H, 317L. Alloy 20, Alloy 330, Alloy 286 and all Duplex Stainless steel grades and Super Duplex grades along with Nickel alloy and Titanium.
Following sizes of stainless steel tubes can be produced in stainless Steel by Harsh Steel:The stainless steel tubes can be manufactured in fixed lengths & random lengths between 4 & 12 meter. Stainless steel Pipes with an outside diameter between 6" (168, 3 mm) and 80" (2032 mm). Harsh steel stocks Stainless steel tubes and standard piping which is ordered in accordance with ASME/ASTM SA/A312 with dimensions and weights in accordance with ASME B36.19. ASME B 36.10 available on request. Lengths of tube are standard 6 meters. We stock austenitic grades in 304L and 316L. Other grades such as Duplex, High Nickel Alloys, heat resistant stainless steels, 904L can be sourced internationally accordance with the customer requirements. Harsh Steel has its very own large bore tube plant that can produce piping from 12 inches to 80 inches diameter in full 6 meter lengths to any International Specification or customer requirement. Heat exchanger tubing can be supplied to client's request. Heat exchanger tubing is available at Harsh Steel in Ferritic, Austenitic or Duplex steels. It can be welded or seamless. The most commonly requested specs are ASTM A269, ASTM A268, ASTM A249, and ASTM A213. Harsh Steel Stainless steel tube sizes vary from 304/L and 316/L tube in sizes " through 36", in Schedules 05S through 80S and larger. Our tubing inventory consists of 6" and 8" OD tubing with wall thicknesses ranging from .083" to .120". We offer Alloy 317L tube stocked in sizes 6" through 12", in Schedules 10S and 40S. In addition to all these different sizing offerings, we also have other 300 series grades available from inventory, in case you do not find exactly what you are looking for.
Harsh steel manufactures ERW (Welded) stainless steel tubes and Tubes from single stainless steel plates in the following size range:Harsh steel material range includes high performance austenitic stainless steel, high temperature austenitic stainless steel, duplex & super duplex stainless steel and nickel alloy grades. The tubes can be produced in single random or double random lengths. Furthermore harsh steel has fully automatic welding equipment to make circumferential welds to enable the supply of double random lengths with a maximum length of 12 meter.
Harsh steel manufactures welded austenitic, duplex and nickel alloy welded stainless steel tubes in accordance with:
Harsh Steel located in Mumbai, Maharashtra, India in the heart of South Mumbai in Asia's Largest Metal market, Maintains extensive inventory of Fasteners such as Stainless steel Thread-forming screws, Stainless steel machine screws, Stainless steel rivets, Stainless steel high-strength socket products, Stainless Steel Fasteners Hex Bolts, Stainless Steel Hex Nuts, Stainless Steel Nylock Nuts, Stainless Steel Studs, and Stainless Steel Washers, Stainless Steel Screws, Stainless Steel Flange Bolts, Stainless steel metric screws, Stainless steel washers, and Stainless steel custom manufactured fasteners along with Duplex Steel, Nickel alloys and Titanium. We provide all kind of Technical Support, Customer Service with a Quality Price.
The Stainless Steel Fasteners which is stocked by Harsh Steel are manufactured in accordance with Relevant International Standards such asDIN, ISO, ANSI OR BSstandards, providing assured quality with processes, systems and proceduresISO9001:2008approved. Harsh Steel is 100% percent focused on customer care with areISO9001:2008compliant for both in house Manufacturing while providing the best service possible to ensure customer satisfaction. We have reputed clients, an extensive and comprehensive stock range, along with competitive pricing and offer a wide range of different sized cut-lengths of all threads from stock.
Harsh steel have carved a niche in the Stainless steel fasteners, Nickel alloy fasteners , Duplex Steel fasteners and Titanium Fasteners industry, and with the rich experience it has resulted in creation of long-lasting relations with the clients globally in International market like Turkey, Czech Republic, Brazil, Iran, Croatia, Bahrain, Iraq, Kuwait, Libya, Oman, Qatar, Saudi Arabia, U.A.E., Yemen, Dubai, Russia.
STAINLESS STEEL NUTS:A nut is a type of fastener with a threaded hole. Nuts are almost always used opposite a mating bolt to fasten a stack of parts together. The two partners are kept together by a combination of their threads' friction, a slight stretch of the bolt, and compression of the parts. In applications where vibration or rotation may work a nut loose, various locking mechanisms may be employed: Adhesives, safety pins or lock wire, nylon inserts, or slightly oval-shaped threads. The most common shape is hexagonal, for similar reasons as the bolt head - 6 sides give a good granularity of angles for a tool to approach from (good in tight spots), but more (and smaller) corners would be vulnerable to being rounded off. Other specialized shapes exist for certain needs, such as wing nuts for finger adjustment and captive nuts for inaccessible areas.
Nuts are graded with strength ratings compatible with their respective bolts; for example, an ISO property class 10 nut will be able to support the bolt proof strength load of an ISO property class 10.9 bolts without stripping. Likewise, SAE class 5 nuts can support the proof load of an SAE class 5 bolt, and so on.
A wide variety of nuts exists, from household hardware versions to specialized industry-specific designs that are engineered to meet various technical standards.
Types of Stainless steel Nuts:
Harsh Steel located in Mumbai, Maharashtra, India in the heart of South Mumbai in Asia's Largest Metal market, Maintains extensive inventory of Fasteners such as Stainless steel Thread-forming screws, Stainless steel machine screws, Stainless steel rivets, Stainless steel high-strength socket products, Stainless Steel Fasteners Hex Bolts, Stainless Steel Hex Nuts, Stainless Steel Nylock Nuts, Stainless Steel Studs, and Stainless Steel Washers, Stainless Steel Screws, Stainless Steel Flange Bolts, Stainless steel metric screws, Stainless steel washers, and Stainless steel custom manufactured fasteners along with Duplex Steel, Nickel alloys and Titanium. We provide all kind of Technical Support, Customer Service with a Quality Price.
The Stainless Steel Fasteners which is stocked by Harsh Steel are manufactured in accordance with Relevant International Standards such asDIN, ISO, ANSI OR BSstandards, providing assured quality with processes, systems and proceduresISO9001:2008approved. Harsh Steel is 100% percent focused on customer care with areISO9001:2008compliant for both in house Manufacturing while providing the best service possible to ensure customer satisfaction. We have reputed clients, an extensive and comprehensive stock range, along with competitive pricing and offer a wide range of different sized cut-lengths of all threads from stock.
Harsh steel have carved a niche in the Stainless steel fasteners, Nickel alloy fasteners , Duplex Steel fasteners and Titanium Fasteners industry, and with the rich experience it has resulted in creation of long-lasting relations with the clients globally in International market like Turkey, Czech Republic, Brazil, Iran, Croatia, Bahrain, Iraq, Kuwait, Libya, Oman, Qatar, Saudi Arabia, U.A.E., Yemen, Dubai, Russia.
STAINLESS STEEL WASHERS:A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such as a screw or nut. Other uses are as a spacer, spring (Belleville washer, wave washer), wear pad, preload indicating device, locking device, cover up engineering mistakes, and to reduce vibration (rubber washer). Washers usually have an outer diameter (OD) about twice the width of their inner diameter (ID).
Washers are usually metal or plastic. High quality bolted joints require hardened steel washers to prevent the loss of pre-load due to Brinelling after the torque is applied.
Rubber or fibre gaskets used in taps (or faucets, or valves) to stop the flow of water are sometimes referred to colloquially as washers; but, while they may look similar, washers and gaskets are usually designed for different functions and made differently.
Washers are also important for preventing galvanic corrosion, particularly by insulating steel screws from aluminium surfaces.
Types of Washers:
Harsh Steels stainless steel flanges from 15NB (1/2") to 600NB (24") in Weld neck. Slip-on, Blind, Lap joint, Bossed, Socket Weld and Threaded according to the following standards are available. Harsh Steel stocks a wide variety of stainless steel flanges.
A286 Solution Treated
A286 Solution Treated is covered by specification AMS 5731 (AMS 5732 Capable) and BS HR52
Solution Heat Treatment: 1800ºF ± 25 (982 ± 14ºC) 1 hour, water/oil quench (AMS)
Hardness: ≥ 217HB or 220 HB (BS), ≥201HB (AMS)
A286 Solution Treated and Aged (1800ºF)
A286 Solution Treated and Aged is covered by specifications AMS 5732, BS HR51, ASTM A638 660 Type 2, ASTM A453 660 Class B
Solution Heat Treatment:
980ºC ± 10 for > 1 hour, followed by air cool (BS)
1800ºF ± 25 (982 ± 14ºC) 1 hour, water/oil quench (AMS)
Precipitation Heat Treatment:
720ºC ± 10 > 16 hours, followed by air cool (BS)
1300-1400 ºF (704-760ºC) hold not less 16 hours, air cool (AMS)
Hardness:
248 - 341 HB or 260 - 360 HV (BS)
248-341 HB (AMS)
A286 Solution Treated and Aged (1650ºF)
A286 Solution Treated and Aged is covered by specifications AMS 5737, ASTM A638 660 Type 1, ASTM A453 660 Class A and EN-2303 (under 4" Bar)
Solution Heat Treatment:
1650ºF ± 25 (899 ± 14ºC) 1 hour, water/oil quench (AMS)
Precipitation Heat Treatment
1300-1400 ºF (704-760ºC) hold not less 16 hours, air cool (AMS)
Hardness
277-363 HB (AMS)
A286 Other
AMS 5853 - 15% cold reduced (160 ksi/ 1103 Mpa tensile strength)
AMS 5726 - 40-50% cold reduced (200 ksi/ 1379 Mpa tensile strength)
Availability
Alloy A 286 is available in Sheet, Strip, Plate, Round Bar, Flat Bar, Square Bar , Hexagon Bar, Forging stock, Wire and Welding Wire. For all stock availability of contact Sales.
Specifications
AMS 5525 Sheet / Stirp / Plate
AMS 5723 (cancelled)
AMS 5726 Bar Work Str 200ksi min
AMS 5731 Bar 1800°F Sol Trtd
AMS 5732 Bar 1800°F Sol Trtd /Aged
AMS 5734 Bar 1650°F Sol Trtd
AMS 5737 Bar 1650°F Sol Trtd /Aged
AMS 5853 Bar Cold Red 160ksi min
AMS 5858 Sheet / Strip (welding gr)
AMS 5895 Bar
ASTM A638 660 Type 1
ASTM A638 660 Type 2
ASTM A453 660 Class A
ASTM A453 660 Class B
BS HR51 Bar 1800°F Sol Trtd /Aged
BS HR52 Bar 1800°F Sol Trtd
BS HR650
AECMA PrEN 2171
AECMA PrEN 2119
AECMA PrEN 2172
AECMA PrEN 2173
AECMA PrEN 2303
AECMA PrEN 2304
AECMA PrEN 2398
AECMA PrEN 2399
AECMA PrEN 3510
AECMA PrEN 2175
AECMA PrEN 2417
ws 1.4980
UNS S66286
We export Stainless Steel A286 to below contries.
Harsh steel is a major stockist and Exporter of Stainless Steel A286 to many countries of the world such as Singapore, Brisbane, Sydney, Melbourne, Australia, Houston, TX, San Diego, San Francisco, Atlanta, USA, Brentford, United Kingdom, Phoenix, Ireland, New Zealand and Canada, Western Australia , Queensland, New South Wales, South Australia, Victoria, Australian Capital Territory, Tasmania, Northern Territory, Ontario, British Columbia, Yukon Territory, Alberta, Manitoba, Saskatchewan, New foundland, Prince Edward Island, New Brunswick, Nova Scotia, Eastern Cape, Gauteng, Kwazulu-Natal, Western Cape, England, Scotland, Wales, Northern Ireland, Lagos, Abuja Capital Territory, Vadodara, Mumbai, Chennai, New Delhi, Mahape, Gurgaon, Noida, Bangalore, Coimbatore, Cochin, Ash Sharqiyah, Ar Riyad, Makkah, Dhahran, Riyadh, Jiddah, Jeddah, Masqat, Kwazulu-Natal, Gauteng, Western Cape, Free State, Eastern Cape, Alberta, Saskatchewan, British Columbia, Newfoundland, New Brunswick, Manitoba, Ontario, Nova Scotia, Quebec, Calgary, Edmonton, Vancouver, Toronto, Birmingham, Brentford, Manchester, Bristol, Sheffield, Milton Keynes, London, Poplar, Edinburgh, Thames Ditton.
Alloy A286 (AMS 5731/ AMS 5732 / AMS 5737 / AMS 5525)
| Grade | US Aerospace/Military | US Commercial | British Specification | European Specification | Other |
| A286 | AMS 5525 Sheet / Stirp / Plate AMS 5723 (cancelled) AMS 5726 Bar Work Str 200ksi min AMS 5731 Bar 1800°F Sol Trtd AMS 5732 Bar 1800°F Sol Trtd /Aged AMS 5734 Bar 1650°F Sol Trtd AMS 5737 Bar 1650°F Sol Trtd /Aged AMS 5853 Bar Cold Red 160ksi min AMS 5858 Sheet / Strip (welding gr) AMS 5895 Bar |
ASTM A638 660 Type 1 ASTM A638 660 Type 2 ASTM A453 660 Class A ASTM A453 660 Class B |
BS HR51 Bar 1800°F Sol Trtd /Aged BS HR52 Bar 1800°F Sol Trtd BS HR560 |
AECMA PrEN 2171 AECMA PrEN 2119 AECMA PrEN 2172 AECMA PrEN 2173 AECMA PrEN 2303 AECMA PrEN 2304 AECMA PrEN 2398 AECMA PrEN 2399 AECMA PrEN 3510 AECMA PrEN 2175 AECMA PrEN 2417 ws 1.4980 |
UNS S66286 |
Technical Data Sheet
| Chemical Composition Limits | ||||||||||||||
| Weight% | C | Mn | P | S | Si | Cr | Ni | Mo | Ti | V | Al | B | Co | Cu |
| A286 | 0.08 max | 2 max | 0.025 max | 0.025 max | 1 max | 13.5-16 | 24-27 | 01/01/05 | 1.9-2.35 | 0.10-0.50 | 0.35 max | 0.0003-0.010 | 1 max | 0.50 max |
Typical Mechanical Properties
| Alloy | 0.2 Proof Stress (min) | Tensile Strength (min) | Elongation (min) |
| Alloy A286 Solution Treated and Aged (BS) | 590 N/mm² | 900 N/mm² | 13.00% |
| Alloy A286 Solution Treated and Aged (AMS) | 85 ksi (586 mpa) | 130 ksi (896 mpa) | 15.00% |
Typical Mechanical Properties 2
| Alloy | 0.2 Proof Stress (min) | Tensile Strength (min) | Elongation (min) |
| Alloy A286 Solution Treated and Aged (AMS) | 95 ksi ( 655mpa) | 140 ksi (965 mpa) | 12.00% |
Products Range :
Nimonic Alloy 90 round bars UNS S07090 WR. NO 2.4632 contain Chromium 18.00-21.00%, Manganese 1.00% max, Nickel balance, Silicon 1.00% max, Carbon 0.2% max, Zirconium0.15% maximum which is commonly used in various daily applications such as turbine blades, hot working tools, exhaust re-heaters, disc and high-temperature springs. Nimonic Alloy 90 bars are available in ASTM A276, ASTM A479, ASTM A484, ASTM A582, ASTM A473 specifications. We Export and Stock Nimonic Alloy 90 round bars along in types of Nimonic Alloy 90 bright round bars, Nimonic Alloy 90 hexagonal bars, Nimonic Alloy 90 square bars, Nimonic Alloy 90 hex bars, Nimonic Alloy 90 flat bars, Nimonic Alloy 90 threaded bars and Nimonic Alloy 90 forged bars. All the Nimonic Alloy 90 bars are available in hot rolled, peeled, annealed cold conditions. Being an ISO 9001-208 we export Nimonic Alloy 90 rounds, hex, square & forged bars with Mill Test certificates or Third party test certificates.
Types of Nimonic Alloy 90 bars we stock:
Application of Nimonic Alloy 90 round bars:Turbine blades, hot working tools, exhaust re-heaters, disc and high-temperature springs.
At Harsh Steel Nickel 800 is available in Incoloy Alloy 800 / 800H/ 800HT wire, Incoloy Alloy 800 / 800H/ 800HT Round bar, Incoloy Alloy 800 / 800H/ 800HT Forged bar, Incoloy Alloy 800 / 800H/ 800HT hex bar, Incoloy Alloy 800 / 800H/ 800HT Flat bar, Incoloy Alloy 800 / 800H/ 800HT Circles, Incoloy Alloy 800 / 800H/ 800HT Ring, Incoloy Alloy 800 / 800H/ 800HT Tube, Incoloy Alloy 800 / 800H/ 800HT seamless Pipe, Incoloy Alloy 800 / 800H/ 800HT Welded / ERW Pipe, Incoloy Alloy 800 / 800H/ 800HT Sheet, Incoloy Alloy 800 / 800H/ 800HT Plate, Incoloy Alloy 800 / 800H/ 800HT Coil, Incoloy Alloy 800 / 800H/ 800HT Flanges, Incoloy Alloy 800 / 800H/ 800HT fasteners, Incoloy Alloy 800 / 800H/ 800HT Socket weld Fittings, Incoloy Alloy 800 / 800H/ 800HTferrule fittings, Incoloy Alloy 800 / 800H/ 800HT Buttweld fittings Like cap, elbow, tee, Reducer.
Incoloy 800, 800h, and 800ht are nickel-iron-chromium alloys with great quality and incredible resistance to oxidation and carburization in high-temperature presentation. These nickel steel alloys are identical with the exception of the more elevated amount of carbon in composite 800h, and the expansion of up to 1.20 percent aluminum and titanium in compound 800ht. Incoloy 800 was the first of these alloy and it was somewhat altered into Incoloy 800h. This adjustment was to control carbon (.05-.10%) and grain size to advance anxiety burst properties. Incoloy 800ht has further alterations to the joined titanium and aluminum levels (.85-1.20%) to guarantee ideal high temperature properties.the nickel compound is double confirmed (800h/HT) and joins together the properties of both forms. incoloy 800h/HT alloy was proposed for high temperature structural applications. The nickel substance makes the alloy very impervious to both chloride stress-consumption breaking and to embrittlement from precipitation of sigma stage. The general corrosion resistance is superb. In the result tempered condition, alloys 800h and 800ht have unrivaled crawl and anxiety break properties. Today, most suppliers, including Harsh steel, just convey the dual certified 800h/HT compound.
Incoloy 800 is principally utilized within applications with temperatures up to 1100° F, where alloys 800h and 800ht are ordinarily utilized as a part of temperatures above 1100° F where resistance to crawl and burst is needed. The compound equalization permits the nickel steel alloy to show fabulous resistance to carburization, oxidation and nitriding climates. Incoloy 800ht won't get to be embrittled much after long times of use in the 1200-1600° F range where numerous stainless steels get to be fragile.Excellent cold structuring qualities ordinarily connected with the nickel-chromium alloys are displayed with 800ht. At the point when frosty framed widely the grain size delivers an obviously undulated surface called "orange peel". Incoloy 800ht could be welded by the regular methods utilized on stainless steels.
In what forms is Incoloy® 800H/HT available at Harsh Steel?
What are the characteristics of Incoloy 800H/HT?
Alloy 800 - The 800 series of alloy (Incoloy 800, 800H and 800HT) are nickel-iron-chromium superalloys that have excellent properties of high temperature strength and resistance to oxidation, carburization and other types of high temperature corrosion. Alloy 800, 800H and 800HT are used in various applications from furnace components, petrochemical furnace cracker tubes to sheathing for electrical heating elements.
Specifications
Stock Availability Of Contact Sales
| Alloy Name | Trade Name | UNS No. | British Specs | American Specs | German Specs |
| Alloy 800Alloy 800HAlloy 800HT(Welding) | Incoloy 800 Incoloy 800H Incoloy 800HT |
N08800 N08810 N08811 |
BS 3072 BS 3073 BS 3074 BS 3075 BS 3076 NA15 |
AMS 5766 Bar and Forgings AMS 5871 Sheet, Strip and Plate ASTM B408 ASTM B564 ASTM A240 ASTM A480 |
Werkstoff 1.4876 Werkstoff 1.4958 Werkstoff 1.4959 |
Technical Data Sheet
| Chemical Composition Limits | |||||||
| Weight% | Ni | Cr | Fe | C | Al | Ti | Al+Ti |
| Alloy 800 | 30-35 | 19-23 | 39.5 min | 0.10 max | 0.15-0.60 | 0.15-0.60 | 0.30-1.20 |
| Alloy 800H | 30-35 | 19-23 | 39.5 | 0.05-0.10 | 0.15-0.60 | 0.15-0.60 | 0.30-1.20 |
| Alloy 800HT | 30-35 | 19-23 | 39.5 | 0.06-0.10 | 0.25-0.60 | 0.25-0.60 | 0.85-1.20 |
| ASTM Grain Size - Alloy 800 is not specified, Alloy 800H is 5 or coarser, Alloy 800HT is 5 or coarser. | |||||||
Typical Mechanical Properties
| Material | Temp | Hardnes BHN | Tensile Strength MPa | Yield Strength (0.2% Offset) | |||
| °F | °C | ksi | MPa | ksi | MPa | ||
| Incoloy Alloy 800 / 800H/ 800HT | 80 | 27 | 126 | 77.8 | 536 | 21.7 | 150 |
| Incoloy Alloy 800 / 800H/ 800HT | 800 | 425 | 67.5 | 465 | 18.8 | 130 | |
| Incoloy Alloy 800 / 800H/ 800HT | 1000 | 540 | 90 | 62.7 | 432 | 13 | 90 |
| Incoloy Alloy 800 / 800H/ 800HT | 1200 | 650 | 84 | 54.8 | 378 | 13.5 | 93 |
| Incoloy Alloy 800 / 800H/ 800HT | 1300 | 705 | 82 | 47.7 | 329 | 15.8 | 109 |
| Incoloy Alloy 800 / 800H/ 800HT | 1400 | 760 | 74 | 34.2 | 236 | 13.1 | 90 |
| Alloy 800HT is a Trademark of Special Metals Corporation | |||||||
Custom Alloy 455 round bars UNS S45500 AMS 5617 contain Copper 1.50-2.50%, Manganese 0.50% max, Nickel 7.50-9.50%, Silicon 0.5% max which is commonly used in various daily applications such as Medical devices and instrument, needles, pins. Alloy 455 in the annealed condition can be strengthened further by relatively low temperature heat treatment. Custom Alloy 455 bars are available in ASTM A276, ASTM A479, ASTM A484, ASTM A582, ASTM A473 specifications. We Export and Stock Custom Alloy 455 round bars along in types of Custom Alloy 455 bright round bars, Custom Alloy 455 hexagonal bars, Custom Alloy 455 square bars, Custom Alloy 455 hex bars, Custom Alloy 455 flat bars, Custom Alloy 455 threaded bars and Custom Alloy 455 forged bars. All the Custom Alloy 455 bars are available in hot rolled, peeled, annealed cold conditions. Being an ISO 9001-2008 we export Custom Alloy 455 rounds, hex, square & forged bars with Mill Test certificates or Third party test certificates.
Types of Custom Alloy 455 bars we stock:
Application of Custom Alloy 455 round bars:Chemical and allied industries, Food and dye production, Heat exchangers, Explosives, Tanks, Valves, Pickling racks, Manufacture of synthetic rubber and plastics, Pharmaceutica
At Harsh Steel Nickel 188 is available in Cobalt Alloy 188 wire, Cobalt Alloy 188 Round bar, Cobalt Alloy 188 Forged bar, Cobalt Alloy 188 hex bar, Cobalt Alloy 188 Flat bar, Cobalt Alloy 188 Circles, Cobalt Alloy 188 Ring, Cobalt Alloy 188 Tube, Cobalt Alloy 188 seamless Pipe, Cobalt Alloy 188 Welded / ERW Pipe, Cobalt Alloy 188 Sheet, Cobalt Alloy 188 Plate, Cobalt Alloy 188 Coil, Cobalt Alloy 188 Flanges, Cobalt Alloy 188 fasteners, Cobalt Alloy 188 Socket weld Fittings, Cobalt Alloy 188 ferrule fittings, Cobalt Alloy 188 Buttweld fittings Like cap, elbow, tee, Reducer.
Haynes 188 / Udimet alloy 188 is a cobalt based nickel-chromium-tungsten alloy with a small addition of lanthanum to give a very protective scale. Alloy 188 combines excellent high-temperature strength with good resistance to both oxidizing environments up to 2000°F and to sulfate deposit hot corrosion. Cobalt Alloy 188 has good forming characteristics and is capable of being forged, hot worked or cold worked, althoug it does work-harden very rapidly so frequent intermediate annealing treatments are recommend for complex forming operations. Cobalt Alloy 188 is supplied solution heat treated at 2150°F and rapid air or water quenched to attain optimum properties. A combination of good fabricability and weldability makes Cobalt Alloy 188 suitable for a wide number of applications, particularly in gas turbine components such as combustors, flame holders, liners and tranistion ducts.
Specifications
Stock Availability Of Contact Sales
| Alloy Name | Trade Name | UNS No. | American Specs | Other |
| Nickel Alloy 188 | Haynes 188 Udimet 188 |
UNS R30188 | AMS 5608 Sheet, Strip and Plate AMS 5801 Welding Wire |
UNS S43100 DMS-1565 |
Technical Data Sheet
| Chemical Composition Limits | ||||||||||||
| Weight % | C | Mn | Si | P | S | Cr | Ni | W | La | B | Fe | Co |
| Alloy 188 | 0.05-0.15 | 1.25 max | 0.20-0.50 | 0.02 max | 0.015 max | 20-24 | 20-24 | 13-16 | 0.02-0.12 | 0.015 | 3 max | Bal |
| Alloy 430 | 0.12 max | 1 | 1 | 0.04 | 0.03 | 16-18 | 0.75 max | 0.5 | 0.5 | 0.05 | 0.05 | |
Typical Mechanical Properties 01
| Material | Temp°F | Yield Strength (0.2% Offset) min | Tensile Strength min | Elongation (%) | Hardness | ||
| ksi | MPa | ksi | MPa | ||||
| Cobalt Alloy 188 Extruded Bar Solution Treated (AMS 5772) | RT | 55 | 379 | 125 | 862 | 45 | ≤302HB |
Typical Mechanical Properties 02
| Material | Temp°F | Thickness (Inches) | Yield Strength (0.2% Offset) min | Tensile Strength min | Elongation (%) | Hardness HRC | ||
| ksi | MPa | ksi | MPa | |||||
| Cobalt Alloy 188 Sheet Solution Treated (AMS 5608) | RT | ≤0.020" | 55 | 379 | 125 | 862 | 40 | - |
| Cobalt Alloy 188 Sheet Solution Treated (AMS 5608) | RT | ≤0.020" | 55 | 379 | 125 | 862 | 45 | - |
| Cobalt Alloy 188 Sheet Solution Treated (AMS 5608) | 1200 | ≤0.020" | 36 | 248 | 90 | 621 | 40 | - |
| Cobalt Alloy 188 Sheet Solution Treated (AMS 5608) | 1200 | ≥0.020" | 36 | 248 | 90 | 621 | 50 | - |
Alloy 230 is a nickel-chromium-tungsten-molybdenum alloy that combines excellent high temperature strength, outstanding resistance to nitriding environments and excellent long term thermal stability. Haynes 230 is easily fabricated and has very good forming and welding characteristics. Due to Haynes 230 combined properties it is very well suited to a wide variety of component applications in the aerospace and power industries. Haynes 230 is used for combustion cans, transition ducts, flame holders, thermocouple sheaths and other important gas turbine components. Haynes alloy 230 is solution treated at 2150 to 2275°F followed by rapid cooling, and is supplied in this condition (as per AMS 5891 and AMS 5878). Haynes 230 can be both hot worked and cold worked and all parts should be annealed and rapidly cooled in order to restore the best balance properties.
Specifications
Stock Availability Of Contact Sales
| Alloy Name | Trade Name | UNS No. | American Specs | German Specs | French Specs |
| Nickel Alloy 230 | Haynes 230 | UNS N06230 | AMS 5878 Sheet, Strip and Plate AMS 5891 Bar and Forgings |
DIN 17744 No 2.4733 | NiCr22W14Mo |
Technical Data Sheet
| Chemical Composition Limits | ||||||||||||||||
| Weight% | C | Mn | Si | P | S | Cr | Co | Fe | Al | Ti | B | Cu | La | W | Mo | Ni |
| Haynes 230 | 0.05-0.15 | 0.30-1.0 | 0.25-0.75 | 0.03 | 0.015 | 20.0-24.0 | 5 | 3 | 0.20-0.50 | 0.1 | 0.015 | 0.5 | 0.005-0.05 | 13.0-15.0 | 1.0-3.0 | Rem |
Typical Mechanical Properties
| Material | Test Temp °F | Ultimate Tensile Strength | 0.2 % Yield Strength | Elongation in % | Hardness HB |
| Haynes Alloy 230 Extruded Bar Solution Treated (AMS 5891) |
RT | 758 Mpa 110 ksi | 310 Mpa 45 ksi | 35 | 241 max |
| Material | Test Temp °F | Ultimate Tensile Strength | 0.2 % Yield Strength | Elongation in % | Hardness HB |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
RT | 793 Mpa 115 ksi |
345 Mpa 50 ksi |
40 | 25 max |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
1000 | 699 Mpa 101.5 ksi |
303 Mpa 44 ksi |
53.7 | - |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
1400 | 539 Mpa 78.3 ksi |
323 Mpa 46.9 ksi |
61.2 | - |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
2000 | 90 Mpa 13.1 ksi |
69 Mpa 10 ksi |
37 | - |
At Harsh Steel Nickel Alloy 601 (UNS N06601) is available in Nickel Alloy 601 wire, Nickel Alloy 601 Round bar, Nickel Alloy 601 Forged bar, Nickel Alloy 601 hex bar, Nickel Alloy 601 Flat bar, Nickel Alloy 601 Circles, Nickel Alloy 601 Ring, Nickel Alloy 601 Tube, Nickel Alloy 601 seamless Pipe, Nickel Alloy 601 Welded / ERW Pipe, Nickel Alloy 601 Sheet, Nickel Alloy 601 Plate, Nickel Alloy 601 Coil, Nickel Alloy 601 Flanges, Nickel Alloy 601 fasteners, Nickel Alloy 601 Socket weld Fittings, Nickel Alloy 601 ferrule fittings, Nickel Alloy 601 Buttweld fittings Like cap, elbow, tee, Reducer.
Inconel 601 is a nickel-chromium combination utilized for applications that oblige imperviousness to corrosion and heat. This nickel alloy emerges because of its imperviousness to high temperature oxidation, remaining very impervious to oxidation through 2200°F. Alloy 601 creates a hard disciple oxide scale which opposes spalling significantly under states of serious thermal cycling. This nickel alloy has great high temperature quality, and holds its pliability after long administration introduction. It has great imperviousness to aqueous corrosion, high mechanical strength, and is promptly framed, machined and welded. Inconel 601's properties make it a material of wide utility in fields like thermal processing, substance preparing, contamination control, aviation, and force era. Nonetheless, alloy 601 is not proposed for utilization in determinedly diminishing, sulfur bearing environments.
Alloy 601 (UNS N06601) is a Nickel-Chromium alloy with an addition of Aluminium for outstanding resistance to oxidation and other forms of high temperature corrosion. Alloy 601 also has high mechanical properties at elevated temperatures. Alloy 601 is used for industrial furnaces, radiant tubes, themocouple tubes and heat treatment equipment, baskets, muffles, retorts. Petrochemical process equipment and aircraft components
In what form is Inconel 601 available at Harsh Steel?
What are the characteristics of Inconel 601?
Specifications
Stock Availability Of Contact Sales
| Alloy Name | Trade Name | UNS No. | American Specs | German Specs | French Specs |
| Nickel Alloy 230 | Haynes 230 | UNS N06230 | AMS 5878 Sheet, Strip and Plate AMS 5891 Bar and Forgings |
DIN 17744 No 2.4733 | NiCr22W14Mo |
Technical Data Sheet
| Chemical Composition Limits | ||||||||||||||||
| Weight% | C | Mn | Si | P | S | Cr | Co | Fe | Al | Ti | B | Cu | La | W | Mo | Ni |
| Haynes 230 | 0.05-0.15 | 0.30-1.0 | 0.25-0.75 | 0.03 | 0.015 | 20.0-24.0 | 5 | 3 | 0.20-0.50 | 0.1 | 0.015 | 0.5 | 0.005-0.05 | 13.0-15.0 | 1.0-3.0 | Rem |
Typical Mechanical Properties
| Material | Test Temp °F | Ultimate Tensile Strength | 0.2 % Yield Strength | Elongation in % | Hardness HB |
| Haynes Alloy 230 Extruded Bar Solution Treated (AMS 5891) |
RT | 758 Mpa 110 ksi | 310 Mpa 45 ksi | 35 | 241 max |
| Material | Test Temp °F | Ultimate Tensile Strength | 0.2 % Yield Strength | Elongation in % | Hardness HB |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
RT | 793 Mpa 115 ksi |
345 Mpa 50 ksi |
40 | 25 max |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
1000 | 699 Mpa 101.5 ksi |
303 Mpa 44 ksi |
53.7 | - |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
1400 | 539 Mpa 78.3 ksi |
323 Mpa 46.9 ksi |
61.2 | - |
| Haynes Alloy 230 Sheet Solution Treated (AMS 5878) |
2000 | 90 Mpa 13.1 ksi |
69 Mpa 10 ksi |
37 | - |
At Harsh Steel Nickel 80A is available in Nimonic 80A wire, Nimonic 80A Round bar, Nimonic 80A Forged bar, Nimonic 80A hex bar, Nimonic 80A Flat bar, Nimonic 80A Circles, Nimonic 80A Ring, Nimonic 80A Tube, Nimonic 80A seamless Pipe, Nimonic 80A Welded / ERW Pipe, Nimonic 80A Sheet, Nimonic 80A Plate, Nimonic 80A Coil, Nimonic 80A Flanges, Nimonic 80A fasteners, Nimonic 80A Socket weld Fittings, Nimonic 80A ferrule fittings, Nimonic 80A Buttweld fittings Like cap, elbow, tee, Reducer.
Alloy 80A (Nimonic alloy 80A) is a wrought, age-hardenable nickel-chromium alloy. Alloy 80A is similar toalloy 75 but made precipitation hardenable by additions of aluminium and titanium. Alloy 80A has good corrosion and oxidation resistance and high tensile and creep-rupture properties at temperatures to 815ºC (1500ºF). Vacuum refined versions are also available. Alloy 80A is used for gas-turbine components (blades, rings, discs), bolts, tube supports in nuclear generators, exhaust valves in internal combustion engines and has many other offshore/marine, automotive and electrical applications.
Stock Availability Of Contact Sales
| Alloy Name | Trade Name | UNS No. | British Specs | American Specs | German Specs | French Specs |
| Nickel Alloy 80A | Nimonic 80A | UNS N07080 | BS 3072 NA20 BS HR1 Alloy 80A Bar BS HR201 Alloy 80A sheet BS HR401 Alloy 80A Tube BS HR601 Alloy 80A Bar (rivet) |
ASTM B637 | Werkstoff 2.4631 Werkstoff 2.4952 |
AFNOR NC 20TA |
Technical Data Sheet
| Chemical Composition Limits | |||||||||||||
| Weight % | Ni | Cr | Ti | Al | C | Si | Cu | Fe | Mn | Co | B | Zr | S |
| Nickel Alloy 80A | Bal | 18.0-21.0 | 1.8-2.7 | 1.0-1.8 | 0.10 max | 1.0 max | 0.2 max | 3.0 max | 1.0 max | 2.0 max | 0.008 max | 0.15 max | 0.015 max |
Mechanical Properties
| Properties | Conditions | ||||
| T (°C) | Treatment | ||||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |||
| Poisson's Ratio | 0.27-0.30 | 25 | |||
| Elastic Modulus (GPa) | 190-210 | 25 | |||
| Tensile Strength (Mpa) | 1158 | 25 | oil quenched, fine grained, tempered at 425°C | ||
| Yield Strength (Mpa) | 1034 | ||||
| Elongation (%) | 15 | ||||
| Reduction in Area (%) | 53 | ||||
| Hardness (HB) | 335 | 25 | oil quenched, fine grained, tempered at 425°C | ||
Physical Properties
| Quantity | Value | Unit |
| Thermal expansion | 16 - 17 | e-6/K |
| Thermal conductivity | 16 - 16 | W/m.K |
| Specific heat | 500 - 500 | J/kg.K |
| Melting temperature | 1370 - 1400 | °C |
| Service temperature | 0 - 500 | °C |
| Density | 8000 - 8000 | kg/m3 |
| Resistivity | 0.7 - 0.7 | Ohm.mm2/m |
X40Cr14 Chemical Composition And Mechanical Properties
| C | Si ≤ |
Mn ≤ |
P ≤ |
S ≤ |
Cr | Ni | Mo |
| 0.36-0.45 | 1.00 | 1.00 | 0.030 | 0.030 | 12.5-14.5 |
D2 steel is an air hardening, high-carbon, high-chromium tool steel. It has high wear and abrasion resistant properties. It is heat treatable and will offer a hardness in the range 55-62 HRC, and is machinable in the annealed condition. D2 steel shows little distortion on correct hardening. D2 steel’s high chromium content gives it mild corrosion resisting properties in the hardened condition.
If you need better machinability then consider A2 tool steel which has a chromium content of 5% and is more readily machinable.
Typical applications for D2 Steel:
Forging:
Heat slowly and uniformly to 700°C then more rapidly to 900/1040°C. Do not continue to forge D2 below 925°C. Reheat as often as necessary to maintain proper forging temperature. After forging cool slowly. This is not an annealing process. After the forging is cold, it must be annealed as described below.
Annealing:
Heat uniformly to 843/871°C, then slow furnace cool at a rate of not more than 10°C per hour. After annealing D2 a maximum hardness of 240 Brinell may be achieved
Hardening:
D2 tool steel is extremely sensitive to overheating during hardening – do not overheat.
Pre heat slowly to 750/780°C and soak. Continue heating to the final hardening temperature of 1000/1030°C and allow the component to equalise. Quench in oil or cool in air.
Tempering:
Heat uniformly and thoroughly to the desired temperature and hold for 25 minutes per cm of thickness. D2 can be double tempering at approximately 15°C below the first tempering, after intermediate cooling to room temperature.
Industrial gaskets and sealing products are widely used throughout the mining, oil and gas, refining, electronic, pipeline, water treatment and petro-chemical industries including a wide range of general engineering applications.
Harsh Steel manufactures and supplies variety of high quality industrial gaskets, produced with the latest technology in the manufacture of gaskets and seals. Harsh Steel Industrial gaskets product range:
Non-metallic gaskets :
Semi-metallic gaskets :
Additional Information:
Payment Terms : L/C, T/T
Packaging Details : sea worthy
Delivery Time : 60 days
Additional Information:
Payment Terms : L/C, T/T
Packaging Details : sea worthy
Delivery Time : 60 days
Additional Information:
Payment Terms : L/C, T/T
Packaging Details : Sea Worthy
Delivery Time : 60 days
The Nickel 600 Pipes and Pipes Fittings are used in Petro-Chemical Industry, Oil and Gas Industry, Nuclear Industry, Pulp & Paper Industry, Research & Development, Mega Projects, Defense & Development Industries. Wing to the special grade of steel Inconel 600, Butt weld Pipe Fittings are used for all critical applications. Aimed to be major industry competition in the markets, we offer Inconel Pipes And Tubes, made from Inconel Alloy 600 which is popular for high heat and corrosion resistance properties. These Inconel Pipes and Tubes come in various lengths, thickness and dimensions to meet the various requirements of different clients. These Inconel pipes and tubes are offered by us in appropriate packaging.
