Jetex Industries

Ghatkopar, Mumbai, Maharashtra

Solid lubricant paste with extremely low coefficient of friction for effective running-in and metal assembly

Applications

• As a low friction running-in, metal priming paste for all new or rebuilt mechanical equipment such as gears, sliding bearings, slide ways, joints, sleeves, splines, cams, journal bearings.
• As a press-fitting lubricant to reduce press-fitting power required and prevent misalignment, seizure, wear, distortion especially under heavy load conditions.
• For lubrication of all sliding metal surfaces to reduce wear, friction and prevent cold-welding of surfaces such as for shafts, bushes, splined shafts, pumps, valves, threaded spindles, moving screws, toothed gears, worm gears and transmission gears, lead screws, machine tool guides, pumps, flanges, anti friction bearings, ball and roller bearings, shafts, bolts and pulleys.
• As a universal assembly paste to reduce tightening torque required; for enabling easy and non-destructive disassembly of components after long operational hours under operating and temperature variations.
• As an antifriction and anti wear lubricant for heavily loaded surfaces under slow sliding speeds for preventing cold welding of sliding surfaces under heavy loads.
• As a standard anti seize compound for all threaded connections during assembly stage for maintenance free dismantling.

Benefits

• Extremely wide service temperature range of -35°C to +450°C
• Low coefficient of friction
• High pressure withstanding capacity
• Load bearing capacity exceeds the yield point of most metals
• Prevents metal-to-metal contact and offers protection from wear and friction
• Prevents seizure, scoring, galling, fretting corrosion and stick slip
• Reduces press fitting force required and prevents distortion or misalignment
• Makes assembly easier and disassembly rapid and non- destructive irrespective of operational period or conditions
• Economical to use owing to its high surface coverage capacity
• Aids running in and provides emergency lubrication during start ups

Directions for UseShake the can vigorously for a couple of minutes before spraying till the bearing noise from inside the container is audible. Repeat before every application. Spray onto a clean, dry and degreased surface. Only a thin film of this lubricant is required. Allow solvents to evaporate. Spray from a distance of 20-30 cms. Repeat if necessary. For cleaning the valve dip- tube after spraying, invert the can and depress the actuator button for a few short bursts till only the clear propellant comes out.

Caution Contains flammable solvents and propellant. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

GeneralUse in well ventilated areas. Avoid continuous breathing of Vapor and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).

Disposal All used and unused product should be disposed of in accordance with state regulations.

HandlingRead instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding personal protective equipment, safe use, physical and health hazards.


Limited WarrantyThe information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Dielectric, non-melting silicone grease like compound for electrical parts insulation and moisture protection

Applications

n
• As a moisture proof seal and protective barrier coating on high tension electrical connections of all electronic, electrical, industrial, marine, aircraft, automotive equipment for providing greater resistance to tracking and effects of corona discharges
n
• As a dielectric seal cum lubricant for switches, cables, cable connectors, high voltage insulators, battery terminals, plastic and rubber parts, bushings, electrical insulation, spark plugs, disconnection junctions, ignition systems to prevent formation of a conducting film of water, eliminate risk of flash overs, minimise electrical leakage and prevent ingress of moisture
n
• For all electrical fittings exposed to marine environments to protect from salt-water corrosion, oxidation, moisture penetration, reduce maintenance and increase wear life of equipment As a protective coating on insulators and bushings in chemical plants to protect them from chemical fumes, vapours and gases
n
• As an assembly lubricant for various metal-plastic and metal- rubber pairings
n
• On to surfaces of ceramics, metals, insulating materials to impart high surface resistivity
n

Benefits

n
• Wide service temperature range from -50C to + 200C
n
• Moisture resistant and excellent water repellency qualities prevent formation of conducting water film
n
• High degree of resistance to salt spray, humidity and corrosives
n
• High dielectric strength
n
• Chemically inert
n
• Very low volatility
n
• Very good thermal and oxidation stability
n
• Consistency is largely independent of temperature and maintains its grease like consistency at high temperatures
n
• Nontoxic, non volatile, non melting and odourless
n
• Compatible with plastic, rubber and metal pairings
n
• Very good adhesion on all metals, glass, plastic, ceramic, rubber substrates
n

Method of Application Apply by means of hand, brush or putty knife. Can also be dispersed in solvents like mineral spirits, xylene or methyl ethyl ketone for thinning the consistency and making it easier to apply by brushing, dipping or spraying. Do not mix with other oils or grease.


Directions For Use (Aerosol only) Shut off equipment and turn off power before spraying. Spray thin, light and even coats onto clean, dry and moisture free surfaces to a thickness of about 0.4-0.5 mm. For optimum use, clean surface dry from moisture. Allow few minutes for solvent to completely evaporate before resuming operations. Removal of the film can be done by normal degreasing solvents.


Caution (Aerosol only) Contains flammable solvents and propellant. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.