Jetex Industries

Ghatkopar, Mumbai, Maharashtra

High Gloss Fast Drying Flexible Acrylic Conformal Coating
ELECTOCOAT is a fast air-drying, lightweight, clear, tough and flexible acrylic coating designed primarily to protect printed circuit boards and electrical / electronic equipment against high voltage arcing, corona shorts, corrosion, ingress of moisture and fungus. It resists rust, tarnish, corrosion, moisture and has excellent waterproofing / weatherproofing abilities. ELECTOCOAT is highly abrasion & scratch resistant and protects electronic equipment completely due to its high dielectric strength. It does not contain any harmful chlorinated solvents, CFCs or ozone depleting chemicals.


Benefits

• Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences
• Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits
• Prevents sparking and corona discharges
• Non-conductive and has good dielectric properties
• Excellent resistance to weak acids & alkalis, water, oils and chemical fumes
• Easily solderable and very convenient for onsite repair jobs
• Conforms to requirements of specifications MIL-I-46058C

Applications Insulation and protection of all electrical, electronic and high- tech equipment of: general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.


Directions For Use - Bulk Mask and protect areas not to be coated. Apply steady even strokes by means of brush. Component to be coated can also be dipped into the coating. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity.


Directions For Use - Aerosol Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.


Caution:- Contains flammable propellant and solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

MoS2 and solid lubricants based air-drying anti friction coating

Benefits

n
• Extremely wide service temperature range of -180°C to +450°C
n
• Low coefficient of friction, high surface load and pressure withstanding capacity
n
• High and low temperature performance
n
• Protects surfaces from wear, galling and seizure
n
• Oil, grease and solvent resistant
n
• Prevents stick-slip and fretting corrosion
n
• Provides clean dry film lubrication and does not accumulate dirt or abrasives
n
• Offers surface protection from corrosion
n
• Lubricates under adverse operating environments such as in vacuum or near radiation
n
• Provides maintenance free permanent lubrication where oil or grease contamination cannot be tolerated
n
• Excellent lubricity and highly abrasion resistant
n
• Increases service life of equipment
n

Applications

n
• As a dry film lubricant for components exposed to abrasive or dusty environments as threaded connections, pins, levers, pivots, splines, bolts, chains.
n
• As a metal pretreatment lubricant prior to assembly for effective running in to reduce wear, friction and eliminate metal to metal contact and seizure.
n
• As a lubricant for components exposed to critical environmental conditions as vacuums, radiation, high temperatures, humidity.
n
• As a heavy duty, high temperature thread compound to prevent seizure and corrosion and facilitate easy assembly and non-destructive disassembly.
n
• As an anti friction coating for metal cutting tools as millers, reamers, taps, drills, gear cutters, punches, dies to prevent sticking, binding and metal build up; increase life of tools, production quality and efficiency.
n
• As an extreme pressure lubricant for heavily loaded or stressed surfaces to prevent wear, friction, galling, scuffing, seizure and fretting as for press fits, pins, levers, pivots, bearings, gears, splines, journals, linkages.
n

Directions for Use Shake the can vigorously for a couple of minutes before spraying till the bearing noise from inside the container is audible. Repeat before every application. Spray onto a clean, dry and degreased surface. Only a thin film of this lubricant is required. Allow solvents to evaporate. Spray from a distance of 20-30 cms. Repeat if necessary. Excess lubricant may fall off during assembly. For cleaning the valve dip-tube after spraying, invert the can and depress the actuator button for a few short bursts till only the clear propellant comes out.


Caution:- Contains flammable solvents and propellant. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.