For quite a few number of years now, we have been supplying the Cross Flow Separator that we manufacture in our very own factories under the guidance of our knowledgeable experts. This separator is made of top notch materials sourced from authentic vendors that account for the premium quality and performance it houses. We deal in bulk and medium sized orders primarily. The rates are affordable and delivery is punctual.

Details :

• In the modern TPI System, the separating surface area is increased vertically by the addition of a number of parallel plates mounted at an inclination. This not only affords a dramatic space saving but also facilitates very small separating diameter.
  
  
• The K-pack TPI consists of a plate pack constructed of closely spaced corrugated plates inclined at a 45° angle or more, depending on the application. Waste water flows through these plated either parallel to the corrugations in "Counter-current Flow" or at right angles to the corrugations in "Cross Flow". Under laminar flow conditions, the short distance between the inclined plates is now the only distance over which the pollutants have to rise or sink before they are intercepted and separated from the mother fluid.

• Imagine a rectangular tank with a surface A containing a liquid to a height H (see figure 1). Flow through the tank is homogeneous and the flow rate = Q The settling or rising velocity of a particle with diameter d is governed by Stoke's Law

• It follows that the tank surface A is inversely proportional to the square of diameter d of the smallest particle which will completely separate. An increase in the efficiency of a separator can, as a result, only be achieved by a considerable increase in the surface A, which leads to the installation of large tanks with large surface area A. The effectiveness of such large tanks is limited due to factors like :
  • Turbulence and short-circuit currents.
  • Variation in ambient temperature.
  • Temperature gradients in the liquid.
  • Surface wind load.

In the modern TPI System, the separating surface area is increased vertically by the addition of a number of parallel plates mounted at an inclination. This not only affords a dramatic space saving but also facilitates very small separating diameter. The K-pack TPI consists of a plate pack constructed of closely spaced corrugated plates inclined at a 45° angle or more, depending on the application. Waste water flows through these plated either parallel to the corrugations in "Counter-current Flow" or at right angles to the corrugations in "Cross Flow". Under laminar flow conditions, the short distance between the inclined plates is now the only distance over which the pollutants have to rise or sink before they are intercepted and separated from the mother fluid.

Application :

• Mineral oil refineries, oil extraction, offshore platforms
• Tank storage farms
• Ballast water treatment
• Petrochemicals
• Galvanizing metal; mining industry
• Edible oil refining
• Foodstuffs industry
• Paper & pulp industry

The Cross flow separator system permits simultaneous separation of floating and settling materials like oils, fibres, sand etc. But are also individually applicable as oil and solids separators. The raw water containing oil and/or suspended solids passes in horizontal direction between the closely spaced plates in the plate pack. Completely laminar flow conditions are established while the water flows across the plate pack from the inlet to the outlet side. Laminar and stable flow conditions are essential conditions for the effective gravity separation of the water, oil and/or the suspended contaminants.

Oil separation : In the course of passing through the plate pack from inlet to outlet, the oil floats upwards info the tops of the corrugations and rises up the incline of the plate to the surface of the separator, where it is removed by a skimmer.

Solids Separation :

• The solids move towards the Bottoms of the corrugations and slide down the incline of ' the plate. From there the separated solids are collected in the sludge compartment of the separator to be partially dewatered and transported by a shaft less spiral conveyor and intermittently discharged through a blow-off valve (optional). Settled sludge cannot decontaminate the treated water. Oil and solids move in separate directions, but both perpendiculars to the flow of water, eliminating particle re-entrainment completely.
• All K-Pack separators are custom built with respect to the number of plates in the pack, the length of the plates, the distance between the plates and the plate incline. The number and the length of plates is determined as a function of the raw water flow rate to be processed in the separator. The distance between the plates is depending upon the concentration of solids / sludge in the raw water. The incline of the plates is set between 45 and 60 degrees depending upon the general nature of the Oil and/or sludge, (density, viscosity, concentration).
• The systems are fabricated in mild steel and other materials are available on request. The oil separators are standard with oil and skimpipe and 45 degree shaped compartment. The solids separators are optionally with a shaftless conveyor in the sludge compartment.
• In the corrugation tops a very high oil concentration is established. This is the ideal condition for oil coalescing to take place (formation of large oil droplets out of many small oil droplets). In the corrugation bottoms a high sludge concentration is established. This is the ideal condition for particle agglomeration to take place (formation of heavy particles from small and relatively light particles)

Applications

• Mineral oil industry
• Edible oil industry
• Metal industry
• Ceramic industry
• Galvanic industry
• Mines
• Sand separation after washing of contaminated soil
• Food industry

With exceptional transportation facilities, our diligent team delivers the product basket in the committed time span. We share a forefront with the famed organizations, supplying superior quality API Oil Separator at affordable rates.

API Oil Water Separators

• The K-Pack API Series, oil/water separators are a gravity differential separation device for removal of free and dispersed oil droplets from only waste streams. The design follows the American Petroleum Institute’s (API) Design & Operation of Oil/Water Separators Manual.
• We have experience using various MOC’s and a strong Engineering team to support demands.

Gravity Separation

• The API steel/RCC design is just a type of oil/water separator designs from K-pack that can be used singularly or in combination with other treatment processes such as emulsion cracking, DAF & clarifier pretreatment.
• The API can be installed above, flush with or below grade. Conversion to a DAF can also be accomplished for flotation where needed.
• The API separator separates via gravity and the density differential of liquids as per Stokes law, which defines the rise rate of an oil droplet based on its density and size. Typically the difference between the specific gravity of the oil and water is much closer than the specific gravity of the suspended solids and water. therefore, the design of the API separator is based on the specific gravity of the oil to be separated and the
• waste water. Using this criteria results in most suspended solids in the API. API effluent is then treated further in more refinery waste water treatment plants.
• API Performance -100mg/1, 150 -micron free, dispersed and non-emulsified oil droplets.
• The typical use of the API separator is to reduce inlet loads of oil and suspended solids in refinery waste water. Following the API further treatment may be required, i.e. coalescing oil water separator as a polishing step and treatment of dissolved organic materials with biological treatment, and/or other treatment technologies (DAF etc.).

Typical Applications :

• Ground water remediation
• Mobile separation system
• Daf/clarifier pretreatment
• Power plant water treatment
• Refinery process water
• Aircraft wash racks
• Machining coolant oil removal
• Tank farm tank bottoms
• Vehicle wash water treatment
• R.O. Filter pre-treatment
• Oil spill recovery
• Trench water treatment
• Bilge water treatment
• Hydraulic fluid tank de-watering

Features :

• All the K-Pack series of API are completely customised to client requirements.
• We have experience in working with all MOCs: carbon, steel, RCC, stainless steel as with non metallic components.
• APIs come with standard components.
• Oil and Sludge are collected through to the bottom.
• They can also be a scrapper mechanism customised to ensure VOC handling.

The TPI Oil Water Separator that we manufacture is among our top selling products as it is much sought after for the premium quality. We ensure high standards of client satisfaction in each and every deal and this has contributed to our increasing number of clients over the years. The rates are reasonable and relatively lower than most others. We are wholesale dealers and entertain bulk and marginal deals.