Our Products
For reduction of tissues, preparation of emulsions, different solutions etc. A powerful 1/10 H.P, 8000 RPM. Motor controlled by a speed regulator fitted with a stainless steel shaft with microcutting blades is mounted on a stand. Rapidly rotating razor sharp blades provides fast and thorough reduction of tissue, for preparation of emulsion of different solutions etc. Micro homogenizing bottles for samples of 2 to 30 ml, 5 to 50 ml and 10 to 100 ml is supplied with the unit. To work on 220 volts A.C.
It withstands high temperature up to 350C . The body of the mantle is spun one piece from non-rusting Aluminium (upto 10 Liters Capacity) duly powder coated. All heating mantles are lagged With special grade mineral wool. To work 220/230 Volts. A.C.
For visualization of test objects under U.V. tube having long wavelength (365 n.m.) and short wavelength (254 n.m.) as desired. A flourescent tube is fitted to the unit for day light visualization. Supplied with three tubes to work on 220/230 Volts A.C.
It is very useful for heating slides to a uniform constant temperature below the melting point of wax. The surace temperature is controlled by hydraulic type thermostat from ambient to 90C. Supplied complete with pilot lamp, cord and lamp, but without thermometer. To work on 220/230 volts A.C. supply.
Fractions take the form of sharp discrete disc. It is a circular bath assembly with a leakproof chamber fitted with 12 gel tubes. The design has been made with detachable upper chamber, fitted with 99.9% PURE PLATINUM ELECTRODES, cable socket and buffer chamber having 12 destaining tubes
Stainless Steel Pass Boxis an equipment normally installed on the wall between the clean room and any other room. It is used for transfer of material from and into the clean room, without contaminating the air of clean room and without having to open room doors. This is achieved with the help of interlocking type doors of pass box. We are well reckoned as one of the prominent Pass Box Manufacturers in Delhi.
Principal of Working :This equipment is installed on the wall between the clean room and the other room. the pass box has two doors at its extreme ends. One door opens in the clean room and other door open in the other room. These doors are electrically interlocked type so that any other door can be operated at a time. This avoids direct flow of air from the clean room to the other room or vice versa. This also abviates the need to open the clean room door frequently for transferring of material from & into the clean room. Thus, it helps in achieving the aim of material transfer without disturbing the cleanliness level of the clean room.
Construction :Our Laboratory Pass Box is made of Commercial board and all its external & internal surfaces are dully laminated. L.M.S. orS.S.sheet body also can be supplied optionally. Each hinged door has wide glass viewing window, through which material kept in the pass box can be seen. These doors are electrically interlocked type, so any one door can be opened at a time. U.V. & fluorescent light and HEPA filter can be provided optionally.
Sizes Available :
This machine is suitable for crushing stoneless fruits and vegetables. This machine is mounted on a heavy duty mild steel stand equipped with motor and starter. The material is fed into the stainless steel hooper which feeds the product into the crushing drum, which consists of stationery blades and rotary beater which crushes the loaded product. With 1.0 H.P. motor (Cap. 500 kg / hr.)
Vertical Autoclave is ideally designed for sterilization of culture media, glassware, utensils instruments etc. in steam under pressure. The Laboratory Vertical Autoclave has steam lined construction i.e. outer body is made of thick mild steel sheet finished with cream enamel painted and inner chamber is made of thick stainless steel. Lid is made of mild steel lined with stainless steel & provided with radial locking systems, worked by a handle at the top. Gasket is of neoprene rubber, hydraulically tested up to 40 psi. The chamber is absolutely leak proof & can be operated at any selected point in between 5 to 20 pound per sq. inch. It is provide with safety valve pressure gauge, pressure release valve, water level indicator with cord & plug. Fitted with automatic cut off device for element for general safety & also fitted with indfoss piezostat. The lid is made of thick mild steel with stainless steel lined inside duly polished.
Dia x Depth Size:
Clean Air ROOM/SAMPLING BOOTHare overhead clean air modules mounted on roof or with steel frame on the ground. Units can be built with / without casters so the clean enclosure can be moved over equipment or used to isolate a controlled process. Overhead Clean Air Modules are basically used for Filling, Refilling Weighing and Sampling/Dispensing of Raw Material, Basic Compounds, Active Compounds etc. The Roof Mounted Clean Air Tent works on the principle of laminar air flow with HPEA Filters & Pre-Filters. Moreover,
Clean Air room provides: - This will act as a CLASS 100 Room for the protection of the personnel in the cabinet from the processed substances by vertical flow of clean air protection of the raw and intermediate products to be processed. Protection of the room where the cabinet is built up and environment from highly active substance which otherwise would disperse in the room and escape in the atmosphere unfiltered. Safe collection and deposition of substance released during work.
For continuous heating upto 350C. The body is made of specially disigned perforated P.C.R.C.
Sheet painted with attractive stove enamel with insulated elements. To work on 220/230 volts A.C.
SIZE (B x L x H)
Cement Autoclave by Scientech Instrument is a perfect cement testing equipment available today. These industrial cement autoclaves are safe to use and come with durable construction.
Cement autoclaves by Scientech Instrument are made of double walled units. Outer chamber is constructed with thick high grade sheet duly pre-treated with primers and painted with stove enamel or power coated ensuring long lasting and rust proof performance. The inner cylinder is made of heavy gauge welded steel sheet. These cement autoclaves are air insulated form inside and in some cases as per customer requirement mineral glass wool insulation is also provided. These units are equipped with strong locking lid which is made of thick stainless steel plate to provide better safety while operating the machine and mounted on a sturdy supporting frame. The pressure inside is controlled by pressure gauge and spring-loaded safety valve. These units come after passing hard research and testing procedure. To deliver long lasting and durable equipment our cement autoclave units are tested up to 2.5times the normal working pressure.
Features:
Model | Description | Capacity | Sensitivity |
SE-350 | Analytical Balance | 200g | 0.1mg |
SE-351 | Chemical Balance | 200g | 0.2mg |
SE-352 | Physical Balance | 200g | 1.0mg |
Double walled with inner chamber made of S.S./Plastic and outer of thick PCRC sheet duly enamel painted . Temperature range from ambient to-20 degree is achived by hermitically sealed comprresor . The gap between the inner and outer wall is filled with high grade PUF Insulation to avoid to avoid thermal loss.
Digital precision scale
Capacity: 220g
Accuracy: 0.1mg
Built-in RS232 output interface
Auto fault detection
To destroy syringe needles from 18 G to 26 G, needle burns electrically & Syringe cuts automatically unit quick in action, portable, noise free with electrical cutter.
Based on the rotating disc-splash plate principal, It produce only super fine particles of micron size, which become part of the atmosphere, thereby reaching every corner of the room, resulting in uniform humidity. Due to the upward thrust imparted to the micron sized water droplets, by high speed motorised unit, they remain suspended in the atmosphere for longer duration of time. Time unit is capable of atomizing upto 3 liters of water in an hour at full evaporation in the driest possible ambient conditions. The unit has body made up of S. Steel unit is effective for an enclosed space of volume upto 40 cu. mts. The unit is provided with high speed 2800 RPM motor to run longer period, and the blades are aerodynamically balanced to ensure dropless fumigation. To work on 220/230 volts. A.C. supply. with automatic humidity control system.
+ 5 to 60C, 30 - 300 rpm
Combined incubator shaker
Digital display for temperature and speed
Integrated timer
Unique retractable platform for easy loading and unloading
Angle adjustable accessory tube racks, with patent pending Magnalock coupling system available
Coms enabled for external temperature measurement
This combined shaker and incubator is ideal for scientists doing cell culturing procedures, especially suspension culture applications. It is compact enough to be positioned on the laboratory bench.
The shaker provides an orbital shaking motion, adjustable between 30 to 300rpm with a gentle start action. The shaking speed is microprocessor controlled and set via the digital LED control panel.
Available in five models
Student Stimulators Transistorised : Out put 0-25 DC in twosteps, duration .5 ro 1.5ms frequency 5 to 100 c/s in 11steps, modes, single, repetitive or an external trigger, for220V 50Hz.
Student Electronic Stimulator Latest Design :
Frequency continuously variable from 0.1Hz to 100Hz in 3decades of 0.1 to 1, 1 to 10 and 10 to 100 selectablethrough push-button controls and one continuously variablecontrol.Output voltage continuously variable from 0 to 30V in twosteps of 1 to 3 and 1 to 30, selectable through a switch.Fixed pulse duration 1m secSingle & external trig. single pulse facilitySensitive speaker to give audible indication or eachoutputHigh stability new circuitry minimises external interference.
Used for V.D.R.L. Tests, blood grouping tests, various agglutination tests or for mixing of solutions in small bottles, flasks or beakers. It has a platform of size 300 x 300 mm. and can accommodate blood Bottles slides or flasks using a spring holder. Supplied complete with cord and plug to work on 220/230 volts A.C.
OTHER INSTRUMENTS BEING MANUFACTURED BY US FOR | |||
|
CAPACITY | ACCURACY | PLATTERS SIZE | DISPLAY |
210gm | 0.0001 gm (0.1 mg) | 80 | LED |
220gm | 0.0001 gm (1 mg) | 110 mm dia | LED |
300 gm. | 0.001 gm (1mg) | 110 mm dia | LED |
150 gm | 0.001 gm (10mg) | 116 mm dia | LED |
300 gm. | 0.001 gm (1mg) | 116 mm dia | LED |
600 gm. | 0.001 gm (1mg) | 110 mm dia | LED |
1500 gm | 0.05 gm (50 mg) | 210 x 290 mm | LED |
3 kg. | 0.1 gm (100 mg ) | 210 x 290 mm | LED |
5 kg. | 1 gm | 6"x6" mm | LED |
6 gm. | 0.2 gm (200 mg) | 210 x 290 mm | LED |
10 kg. | 0.5 gm (500 mg) | 210 x 290 mm | LED |
30 kg | 1 gm | 210 x 290 mm | LED |
PRECISION/SILVER WEIGHTING/GENERAL PURPOSE WEIGHING SCALE (WITH DUAL DISPLAY & BATTERY BACK UP) | |||
1500 gm. | 0.1 gm (100 mg.) | 245 x 290 mm | LED |
3 kg | 0.2 gm (200 mg.) | 245 x 290 mm | LED |
6 kg | 0.5 gm (500 mg.) | 245 x 290 mm | LED |
15 kg | 1 gm | 245 x 290 mm | LED |
30 kg | 2 gm | 245 x 290 mm | LED |
60 kg | 5 gm | 400 x 400 mm | LED |
PLATE FORM SCALE (WITH DUAL DISPLAY & BATTERY BACK UP) | |||
60 kg | 5 gm | 500 x 500 mm | LED |
150 kg. | 10 gm | 500 x 500 mm | LED |
300 kg | 20 gm | 500 x 600 mm | LED |
500 kg | 50 gm | 500 x 600 mm | LED |
Electrically operated with quick release chuck taking wide variety of interchangeable nylon brushes for cleaning syrings, test tubes, bottles etc. Model (a) and (b) are table model mounted on a heavy base and have single chuck. Machines with soaking tanks have 12 rinsers and two drill chuck to hold variety of brushes, and are mounted on sturdy angle iron frame duly painted.
Having combined units with array of 10 LEDS, buzzer, auto burette, adjustable timer, dual platinum electrode and other accessories.
We bring forth an automaticIce Flaking Machinefor your hygienic Ice flakes requirement in research laboratories, chemicals, pharmaceuticals, medical, biotechnological and hotel industries. The Automatic Ice Flaking Machine utilizes running tap water and converts it in the form of ice flakes continuously. It is a compact, self-contained unit, covering less floor area & easily installable. the top Ice Flake Maker.
Constructions :Ice flake is housed in styled M.S painted body with stainless steel made bin with no changes of corrosion. Ice crusher used is made of S.S. to give life long performance.
Water is introduced into crusher assembly through a precision float valve. The inflow of water is smoothly controlled by this float valve for maintaining a required lave of water irrespective of variation in pressure at the water input line with automatic cut off in case of low water / no water supply.
Ice flakes are collected into a well-insulated stainless steel container. So it stays for longer time. The removal of flakes is easily possible through the stainless steel front/top door which can be pushed while removing the ice. Moreover the equipment fitted with an ICE LEVEL CONTROLLER, which will put off the system in case ice gets accumulated in the container move than the required level. Hence, there is no need of an operator being on the machine all the time. The ice controller is provided with a drain line for occasional cleaning of the container.
Test two kinds of seed:(big shape and small shape, big grain and small grain, big granule and small granule )
The motor stirrer having maximum speed upto 4000 r.p.m. unit is clamped to a C.P. rod fitted on a heavy cast iron base. The height and angle of the stirrer can be adjusted according to the requirement. Variable speed Motor with speed regulator is fitted with S.S. Stirrer rod to give smooth and noiseless operation.
CAPACITY:
Scientech Ampule Filling & Sealing Machine(Electric Operated)Ampule Filling & Sealing Machine motorised with capacity adjustment.
Heavy duty model, this is a simple hand operated machine for simultaneous langing of both sides of a round can.A toggle motion balanced hand enables the machine to be operated with minimum exertion.
This is a heavy duty machine mounted on a mild steel stand , suitable for seaming cans of size 201-700 dia and of 9-3/8' height range. Used for seaming processed food cans ensuring a optimum quality hermetic seam. This is versatile and ideally suited to frequent changeover to various sizes of cans. Fitted with 1.0 H.P motor.
Supplied with one set of seaming chuck, seaming roller and adopter plate.
(A) Hand Can Seamer (Hand Operated ) with one set seaming chuck.
Cap 250 cans of 401 dia mild steel thick plate fabricated. Suitable for sterilization of cans after seaming. Complete with pressure gauge, safety valve, & metal clad thermometer and one no. suitable cage.
Crown Cap Sealing Machine We are manufacturer of crown Cap Sealing machine suitable for sealing crown corks on glass bottles. Crown Cap Sealing Machine are highly appreciated for their easy operate.
We are engaged in offering high quality Tray Dryers that are highly acclaimed by the clients for their accurate functions, best control circulated air and temperature. These are provided with extra heavy construction, heat distribution and have high capability to carry load that further results in dependable equipment. Available in single and two compartments, these are used for various application with different tray capacities.
If delivers a current of any value between 1-100 MA (500 Volts Max.) in a constant current mode, and a voltage of 0.500 Volts (100mA MAX.) in constant voltage mode. The range control potentiometer makes the output adjustable over the entire range of the unit. It has line and load regulation 0.5% and rapple less than 10 mV.
All supplies are short circuit and overload protected. Range 0-500 volts & 0-100 mA
(with Two Digital Meters)
Flocculator has been specially designed for use in water treatment plants to correctly estimate the dosing of alum and such other coagulants for treatment of water and sewage. In provides indentical test conditionsfor all samples. Illuminated base consists of fluorescent tube mounted below translucent plastic plate to provide diffused cold light through floc sample. Flocculator consists of geared continuous run heavy duty 1/20 H.P. variable speed motor from 10 to 100 RPM with built in speed control. S.S. stirring rods are provided with adjustable spacer s to adjust the depth of stirring paddles. The stirring shaft can be removed without disturbing other stirrers. This unit is supplied without beakers to work on 220/230 volts A.C.
The body is made of P.C.R.C. sheet duly powder coated paint.The top cast iron heating plate is round having 20 cm. Dia, with heating elementsof 1.5 kw rating. Temperature is controlled by energy regulator upto 350C.
This machine is designed to emboss standard ends with the required reference letters or fingures The machine is operated by a foot treadle which. when depressed, embosses the lid by virtue of marker dies,
without piercing it. Supplied with one set of double row die holder, but without alphabets
and numerical
Cost of alphabets (A to Z) and Numerical (0 to 9)
P.P. Cap Sealing Machine that we offer is mainly used for pilfer proof capping of bottles. Depending upon the capacity of the operator, this machine can seal 900 to 1200 bottles/ hr. We provide our machine with bottle resting tray and dies for sealing 22, 25 & 28 mm neck bottles. One can easily adjust this machine as per the requirement.
Suitable for all sizes of bottles for threading and sealing operations. Supplied one die. Hand Worked Table Model
Heavy Duty Hand Worked Pedestal Model
It is a rugged, reliable elegant and compact blood and chemical analyser. It performs the end point chemical and biochemical analysis accurately and connectration and displayed directly on the digital display. It has 8 high standard glass filters ranging from 400 to 680 nm. wave length. Complete with 6.8V/250mA tungstone lamp light source, special selenium Photocell Detector and sample system of 15mm. dia matched glass cuvettes.
We manufacture high qualityFreeze Dryer/LYOPHILSERwhich has gathered wide admiration in numerous industries. Our High Sensitive Freeze Dryer performs to perfection in every single application. The Biological Freeze Dryer available with us is ideal for curtailing bacterial growth and enzyme actions. We are one of the chief Pharmaceutical Freeze Dryer Exporters from India.
Freeze Drying is the process of removing the moisture from a biological product while maintaining the Integrity of the products biological & chemical structure and activities. Freeze Drying technology is used in particular for removal of moisture from the products usually of biological origin without causing any noticeable change in the original characteristics. Freeze Drying is also the preferred process in the field of Pharmacy, Chemistry and in conservation of food.
ADVANTAGE OF FREEZE DRYER
Heat-sensitive biological materials may be freeze-dried without affecting their potency. The dried materials may be stored for years at room temperature without loss of their original characteristics.
The freeze-dried material may be transported and shipped in small containers, and no provision is necessary for refrigeration en route.
Bacterial growth and enzyme action do not take place in freeze-dried products. Proteins do not coagulate.
Oxidation of many materials such as hemoglobin and vaccines is completely prevented when drying and sealing is done under high vacuum.
A Powerful tool in dissection study of Zoological specimens, Botanical specimens, Industriesetc. Ergonomically designed, The optical system feature 130 m.m. dia lens having a view dia of120m.m. Illumination consists of a 22 watts circular tube for shadowless cool glare free view, It has aarea magnification of 4 x and can be magnified upto 10 x using an auxillary parallel lens (optional)
Streamlined standard equipment incorporated with latest technology for cutting serial section in research work. The precise feed mechanism cuts section from 1-50 microns in steps of one micron each.
Free Adjustments: 1-50 microns. Total feed excursion 28mm with opening of object clamps 37x27mm. Overall dimensions 16x10x9 Complete with razor 120 mm with 120mm with back & handle, honing plate, object holder set of three, oil can. Packed in a wooden box.
It is a double walled unit with inside made of thick S.S. sheet and outer made of M.S. Steel duly powder coated prevents falling of condensed water droplets on the specimens. Heating is achieved through a immersion type heater and the temperature is controlled by hydraulic type thermostat with an accuracy of 0.5C. The bath has an oscillating tray riding on ball rollers oscillated through a geared variable speed motor. Shaking speed range is between 40 to 140 cycles per minute. The shaking tray can either hold test tubes or erlynmeyer flasks of 25 ml or 50 ml or 100 m or250 ml or 1000 ml. as ordered by the users. (Kindly mentioned the capacity of the flasks while ordering). Supplied complete with one shaking tray, paramedical cover, L-shaped thermometer cord and plug, to work on 220/230 volts A.C. supply. Available with heating arrangement only (having temperature range from ambient to 100C) or with both heating and cooling arrangements (having temperature range from 5C to 60C).
INSIDE SIZE :
Scientech Vacuum Pumps are mounted on a heavy steel base plate, and have a wide range of oil sealed pumps. Fitted with heavy duty electric motor, all pumps are V-Belt driven at a speed of 1400 RPM. Pumps are fabricated out of high grade cast iron and are worked on sophisticated machines to give accuracy in microns, thus leading to very high sustained vacuum. Supplied in single stage or double stage models. All SCIENTECH vacuum pumps are fitted with belt guard, vaccum gauge as a standard feature. To work on 220/230 volts A.C. supply.
This Viscometer bath is used to maintain the correct constanttemperature for estimating Kinematic Viscosityof Oil and Petroleium Products in this type of Bath various viscometer may be fixed as an internal part of the bath. The bath is rectangular shape. Inside tank is made of Stainless Steel. The bath is controlled by an Digital Temperature Controller cum indicator. Temperature Range 5 C above room temperature to 100 C-0.1C. Stirring is done by a FHP electric motor stirrer. Heating is done by means of tubler type heater fitted on top of the bath. Itis supplied with viscometer tube holders and s. steel cover. Differentsize & accommodation are available as under without Viscometer tube. Kinematic Viscometer Bath chamber size : 12 x 9 x 12 deep to accommodate6 Viscometer.
These are double walled units with outer made of M.S. sheet duly powder painted and inner made of heavy gauge S. Sheet. Gap between the two walls is duly filled with high grade glass wool to avoid thermal loss. Temperature range from ambient to 150C is controlled by Digital Temperature Controller with an accuracy of 1C. It is capable of with standing a high vacuum. Provided with vacuum gauge, see through transparent window of toughened glass and one shelf. To work on 220/230 Volts A.C. supply.
INSIDE SIZE (DIAxDEPTH)
It works on the principle of substitution of weights and has a special allow casted beam with
magnetic damping device. Fitted with a heavy duty step down transformer to work in 220/230
volts. A.C. supply.
Model Capacity Optical Scale Sensitivity
SE-20 200g 1000g 0.1mg
SCIENTECH Dehumidifiers are water condensing type. base on Refrigeration Cycle to avoid use of expensive chemicals required for dessicant type models. The unit is self standing and is mounted on a study angle iron frame, fitted with caster wheels. Dehumidifier excess moisture from the atmosphere and it fitted with hermetically sealed compressor. Heat exchanger and water condensing coils aremade of S.Steel collection tank is provided below the unit to collect condensate water, Humidity is controlled by automatic HUMIDISTAT incorporated in the unit upto 30% 3% RH, depending upon the ambient conditions. To achieve very low humidity, the room should have a independent window type Air Conditioner to match with the dehumidifier heat load in the room. Suitable to work on 220/230 Volts A.C. Supply.