We are offering push back auditorium seats.
Push back chair particular specification
1. push back type auditorium chair will be of best quality finish and of the design.rn2. molded polyurethane foam will be used in seat and back of chair. The foam will be non sagging type with 50 kgm³ density.rn3. crc sheet in push back system and side stand of the approved quality and thickness as shown in drawing (photograph) shall be used.rn4. m.s. Tube of 50 mm x 25 mm size shall be used in frame of seat and m.s. Flat of size 25 mm x 6 mm in frame of back.rn5. m.s. Flat of size 25 mm x 6 mm from arms and of size 40 mm x 4 mm for arm holder will be used.rn6. m.s. Flat of size 12 mm x 3 mm shall be used in seat and back frame of chair.rn7. abs beading in front of side stand (as per model if required) to hold the fabric shall be used.rn8. push back systemrn• synchronized push back system, with seamlesswelding less 16 g seat supporting tray (as per model).
• 2 nos 14 g back clamps.
• 2 nos 16 g roller holders with 2 nos 30 mm rollers.
• 2 nos 50 x 25 mm ms tubes of 16 g tubes.
• 4 nos of 25 x 6 mm ms flat arms.rn9. side standrn• heavy gauge as per design and construction.
• heavy gauge one piece footrest.
• covered with duly laminated upholstery fabric as used in seat and back.rn10. ppcp molded back cover (as per model if required).rn11. arms rests (with or without cup holder) will of ppcppolyurethane foam molded in shape and design.rn12. the distance between center to center of arms of the chair will be 21” to 23” as per requirement.rn13. the total height of the chair from floor level shall be 37”.rn14. seat and back and side stand will be covered with 100% polyester fabric, fire retardant grade (if required).rn15. the chairs will be installed and fixed with minimum 4 numbers heavy duty anchor fasteners.

We are offering push back auditorium seats.
Push back chair particular specification
1. push back type auditorium chair will be of best quality finish and of the design.rn2. molded polyurethane foam will be used in seat and back of chair. The foam will be non sagging type with 50 kgm³ density.rn3. crc sheet in push back system and side stand of the approved quality and thickness as shown in drawing (photograph) shall be used.rn4. m.s. Tube of 50 mm x 25 mm size shall be used in frame of seat and m.s. Flat of size 25 mm x 6 mm in frame of back.rn5. m.s. Flat of size 25 mm x 6 mm from arms and of size 40 mm x 4 mm for arm holder will be used.rn6. m.s. Flat of size 12 mm x 3 mm shall be used in seat and back frame of chair.rn7. abs beading in front of side stand (as per model if required) to hold the fabric shall be used.rn8. push back systemrn• synchronized push back system, with seamlesswelding less 16 g seat supporting tray (as per model).
• 2 nos 14 g back clamps.
• 2 nos 16 g roller holders with 2 nos 30 mm rollers.
• 2 nos 50 x 25 mm ms tubes of 16 g tubes.
• 4 nos of 25 x 6 mm ms flat arms.rn9. side standrn• heavy gauge as per design and construction.
• heavy gauge one piece footrest.
• covered with duly laminated upholstery fabric as used in seat and back.rn10. ppcp molded back cover (as per model if required).rn11. arms rests (with or without cup holder) will of ppcppolyurethane foam molded in shape and design.rn12. the distance between center to center of arms of the chair will be 21” to 23” as per requirement.rn13. the total height of the chair from floor level shall be 37”.rn14. seat and back and side stand will be covered with 100% polyester fabric, fire retardant grade (if required).rn15. the chairs will be installed and fixed with minimum 4 numbers heavy duty anchor fasteners.