Sansel Instruments And Controls - PH Meter

The CC 603 - 1 series of Conductivity Controller and Transmitter provides a reliable method of Monitoring, Controlling & Transmitting 4 - 20mA / RS 485 MODBUS RTU Communication for Interfacing to PLC, Data logger, HMI, etc., . This product is suitable to measure Conductivity in water treatment, Electrolytic water cleaning, Chemical Industries, Food Process, Waste Water treatment, Textile Industries & Neutralization process, etc. This Conductivity Controller & Transmitter can Measured using Industrial Conductivity Sensors, Temperature can be measured using temperaturesensor.

Features :

• Economical, Easy to Calibrate and Setup
• User selectable 5 ranges from 1μS to 200mS
• High Accuracy
• Programmable Auto / Manual Temperature Compensation
• Optional Isolated RS 485 communication with MODBUS RTU protocol
• Optional Galvanically Isolated 4 - 20mA Output
• Adjustable Cell Constant for particular ranges
• Manual single or 2 point Calibration
• 2 Relay Outputs with Configurable individual H / L Setting with 6 relay status
• Optional audible inbuilt buzzer Output
• Universal Supply Voltage 90 to 270V AC / DC

Specfications :

• Display 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
• Cell Constant * 0.01 / 0.1 / 1(user selectable depends on range*)
• Range (any one) 1 - 20μS, 5 - 200μS, 10 to 2000μS, 1 to 20mS, 5 to 200mS
• Resolution 0.01μS to 0.1mS (depends on range)
• Temp. Compensation Manual / Automatic (-20.0 to +150.0ºC)
• Temp. Sensor RTD - PT 100 (3 wire)
• Temp. Coefficient 0 to 3 % / ºC(user adjustable)
• Electrode Input Conductivity cell on rear panel
• Accuracy ± 1 % of range ± 1 digit
• Set Point - 1 & 2 Two Set Point with 6 Relay Status Selectable
• Relay Output Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating
• Relay Hysterisis 0 to 500 counts (user adjustable)(only for High & Low control modes)
• Relay Cyclic delay 0 to 100 seconds (user adjustable)(only for High & Low control modes)
• Alarm Output(optional) inbuilt audible buzzer with front key reset
• Optional Re. Tx. output Galvanically Isolated 4 - 20 mA
• Optional Comm. output Isolated RS 485
• Comm. Protocol MODBUS RTU
• Operating Environment -10 to 50ºC / 10 to 95 % RH Non Condensing
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x 96 x 85 mm.
• Cutout Dimension 92 x 92 mm
• Weight 500 grams (Approx.)

The ORT 601 - 1 series of ORP Controller and Transmitter provides a reliable method of Monitoring, Controlling & Transmitting 4 - 20mA / RS 485 MODBUS RTU Communication for Interfacing to PLC, Data logger, HMI, etc., .This product is suitable to measure ORP in water treatment, Electrolytic water cleaning, Chemical Industries, Food Process, Waste Water treatment, Textile Industries & Neutralization process, etc., . This ORP Controller & Transmitter can Measured using Industrial PlatinumORP Sensor.

Features :

• Economical, Easy to Calibrate and Setup
• Wide range from -1999 to 1999 ORP
• High Accuracy
• Optional Isolated RS 485 communication with MODBUS RTU protocol
• Optional Galvanically Isolated 4 - 20mA Output
• Very High Input Impedance >10 Ohms
• User selectable Single or 2 point calibration
• 2 Relay Outputs with Configurable individual H / L Setting with 6 relay status
• Optional audible inbuilt buzzer Output with front key reset
• Universal Supply Voltage 90 to 270V AC / DC

Specifications :

• Display 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
• Input Impedence >1012 Ohms
• Range -1999 to +1999 ORP
• Resolution 1 ORP
• Electrode Input Platinum Electrode with BNC Attachment
• Accuracy ± 1 ORP ± 1 digit
• Set Point - 1 & 2 Two Set Point with 6 Relay Status Selectable
• Relay Output Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating
• Relay Hysterisis 0 to 500 ORP (user adjustable)(only for High & Low control modes)
• Relay Cyclic delay 0 to 100 seconds (user adjustable)(only for High & Low control modes)
• Alarm Output(optional) inbuilt audible buzzer with front key reset
• Optional Re. Tx. output Galvanically Isolated 4 - 20 mA
• Optional Comm. output Isolated RS 485
• Comm. Protocol MODBUS RTU
• Operating Environment -10 to 50ºC / 10 to 95 % RH Non Condensing
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x 96 x 85 mm.
• Cutout Dimension 92 x 92 mm
• Weight 500 grams (Approx.)

SANSEL pH 302 Model pH / ORP meter that offer high Accuracy pH, ORP and Temperature Measurement in a Single Unit. It has 16 Character x 2 Line LCD Display and read pH / ORP and Temperature at a time with Engineering Unit. These Technologically advanced Meter build with easy Calibration Steps. Automatic and Manual Temperature Compensation is Selectable for pH Parameter. Two Point Calibration is provided for ORP Measurement.

Features :

• Micro Controller Based High Accuracy
• Three Parameter in One Unit
• Quick and Easy Calibration, Upto 3 Calibration Points with Auto Buffer Recognition.
• Selectable Automatic / Manual Temperature Compensation.
• Non-Volatile Memory to Hold Your Setting and Calibration Points, When Power is OFF.
• ombined Electrode for pH with BNC attachment
• Special Temperature sensor for Automatic Temperature Compensation(ATC)

Specifications

• Range 0 to 14 pH / -1999 to +1999 mV / 0 - 150 °C
• Input Impedance > 10¹² Ohms
• Resolution 0.01 pH / 1 mV / 0.1 °C
• Temperature Compensation 0 to 50 °C Manual / Automatic
• Display 16 character x 2 line LCD with Backlight
• Accuracy ± 0.01 pH ± 1 digit / ± 1 mV ± 1 digit / ± 0.5 °C ± 1 digit
• Electrode Combined pH Electrode with BNC attachment
• Temperature Sensor Provided with 3 pin Female socket
• pH / ORP Input connection BNC socket
• Temperature connection 3 pin male socket
• Operating Environment 0 to 50 °C / 20 to 95 % RH non condensing
• Power supply 230V AC / 50 Hz ± 10%
• Overall Dimension in mm 185 x 185 x 80 (L x B x H)
• Instrument Weight 1.7 kg(Approx.)

Accessories

• Basic Instrument
• Combined pH Electrode
• 4 & 7 pH standard tablet with container
• Electrode Clamp & stand set
• Instruction manual

Optional

• Platinum ORP electrode (Extra charge)
• Imported certified Standard buffer Solution (Extra charge)
• Epoxy body imported Combined Electrode (Extra charge)
• 4 & 7 pH standard tablet with container (Extra charge)

SANSEL make online pH indicator Model pH 641 is a precis, rugged and weather proof instrument carefully designed for the most accurate measurement of pH in all industries. These instruments are completely IC version using “MOSFET” input “OP -AMP” and CMOS ICs. This instrument is a panel mountable with a compact standard size of 48 x 96 x 65mm with front end potmeter type easy adjustable 4pH & 7pH buffer calibration option. This instrument operates from 90V to 270V AC / DC , 50Hz.

Features :

• 3½ Digit seven segment LED display
• High accuracy
• Easy front end two point buffer calibration
• Very high input impedance > 10¹² ohms
• Compact size
• Rugged and weather proof enclosure
• Variety of electrode fittings
• Universal Supply voltage 90 to 270V AC / DC, 50 Hz

Accessories

• Basic Instrument
• Panel mount Clamp set
• Instruction manual

Optional

• Combined Electrode with PP adapter for easy pipe line fitting
• 4 & 7 pH standard tablet with container
• Imported certified Standard buffer Solution (Extra charge)
• Pipe line Flow Through assembly (Extra charge)
• “L” type PVC setup for electrode for Tank installation (Extra charge)

SANSEL make TDS indicator is extremely useful for fast and accurate determination of total dissolved solids in a liquid. The use of solid state technology and IC circuitry makes this instrument versatile and reliable. The factory set fixed range is available. The instrument is ideal for testing of natural water, drinking water, waste water, brine solution, sea water and soluble salts, etc.,

Features :

• 3½ Digit seven segment LED
• Wide ranges
• Front Zero & Span calibration
• ± 1% of FS accuracy
• Compact size
• Easy mount
• Variety of electrode fittings
• 90 to 270V AC / 50Hz operating supply