Our Products
Leading Manufacturer, Supplier & Retailer of Bhma Lock Cycle Test Machine, ZNGAS-10 Gas Detectors Test Chamber, Bhma Over Line Hinge Test Machine, Smoke Alarm Test Tunnel and SM210 Aerosol Generator.
Equipment Function
The smoke alarm test tunnel was designed for sensitivity test of Smoke alarm or Heat detector according to GB 20517GB4715EN 14604EN 54-7 and ISO standards. It consist of test tunnelaerosol generator, obscuration sensor, heat element, controller and computer. The obscuration meter was made of high quality imported part to ensure precision and stable reading. The Zomtest Smoke Test Tunnel Software in English was designed by our software expert specifically to meet the standards test requirements.
Specification
1 ModelZNEN14604-1
2 Power220V AC 1KW
3 StandardsEN14604, EN54-7, GB20517, GB4715
4 Aerosol generatorLiquid paraffin , particle size distribution between 0.5m1.0m
5 Optical smoke densitometer: transmitted light, wavelength 880nm950nm, range: 02 dB/m,
6 Test tunnel size: 2.1m x 0.5mx 1.1m.
7 Test section size is 430mm x 270mm
8 Wind speed: DC motor speed regulation, software setting speed, from 0 1.2 m/s
9 Smoke rising rate: preset 0.005dB/m, can be set in the software
Test Items
1.
2.
3.
4.
5. T
6. 22W250mm
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Equipment Function
The smoke alarm production test tunnel is used for batch test or calibration smoke alarm and detector in production process. The main parts, aerosol generator and obscuration meter are fully same as standards smoke tunnel to ensure high reliable test result. The aerosol concentration in the smoke box is controlled by fine-tuned PID to maintain constant OBS of smoke in a narrow range of +/-0.004dB/m. The smoke alarm production test tunnel is installed on production assembly line. The alarms are placed on the conveyor belt and flow into the smoke box. After passing through the smoke box, check the status of the alarm. You can batch quickly test the smoke alarm or calibrate the sensitivity. The specially developed zomtest smoke test tunnel software carries out constant smoke control and continuous monitoring of smoke concentration. The speed of the conveyor belt shall be adjusted according to the response time of the sensor to improve the production efficiency.
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Equipment Function
The smoke alarm production test tunnel was designed for batch test or calibration of sensitivity test of Smoke alarms or detectors. The basic work principle is compliance to EN 14604 and EN 54-7. It consist of test tunnelaerosol generator, obscuration sensor, controller and computer. The obscuration meter was made of high quality electrical and optical components to ensure precision and stable reading. The two floor trays support by rodless air cylinders. They can extend and extract by press button or automatic control. The lids are fixed on tray and can close the opening in extended position and extraction position. The Zomtest Smoke Test Tunnel Software in English is able to set the air speed, aerosol buildup rate (ramp test), constant obs set value.
The aerosol concentration is controlled to set value by PID algorithm and can maintain the smoke density with +/-0.004dB/m in reading when door keep closing. After exchange of samples tray, the smoke density will drop and then resume to +/-0.005 range within half minute.
Specification
1 ModelZNEN14604-18
2 Power220V AC 1KW
3 StandardsEN14604, EN54-7, GB20517, GB4715
4 Aerosol generatorLiquid paraffin , particle size distribution between 0.5m1.0m
5 Optical smoke densitometer: transmitted light, wavelength 880nm950nm, range: 02 dB/m,
6. 3.1m x 0.5mx 1.1m
7. 430mm x 270mm
8. 0 1.2 m/s
9.0.005dB/m
Obscuration Modbus RTU com RS 485
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
zomtest SM210 20-25kw 200W 12VDC 29 12 23 zomtest
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Equipment function:
The aerosol generator atomizes liquid paraffin into aerosol through the nozzle. It is mainly designed for the sensitivity and function test of smoke alarm and detector. SM220 aerosol generator adopts compressed gas to atomize liquid paraffin, therefor the aerosol generator includes precision pressure regulating valve and pressure gauge and time controller. It combines two operation modes: external and internal control modes. In external control mode, the aerosol on/off is controlled by 20VDC input signal. In internal control mode, the aerosol on/off is controlled by embed timer and external 24VDC power supply. The work duration and time interval are settable on time controller.
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Equipment Function
The equipment is intended for gas alarm or Carbon monoxide alarm sampling test. The equipment provides a sealed stainless-steel chamber with glass door for monitoring alarm status. The volume of chamber and size of samples shelves are custom-made. It can contain about 10 alarms. The controller control high speed valve to inject quantitative high concentration gas into chamber and the gas stirred by circulating fan to get homogeneous test gas in certain concentration. That gas will be test gas for response test or threshold setting of gas alarm product. The air speed are adjustable to get uniform test gas and avoid the high concentrating gas getting into alarm directly during gas injection.
Parameter
1) ModelZNGAS-10
2) Power supply220vAC, 1 kW
3) Applicable standardEN50194-1, EN50291-1
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Equipment Function
The equipment is intended for gas alarm or Carbon monoxide alarm testing and calibration in mass production in advantage of its big volume. The equipment provides a sealed stainless-steel chamber with glass wall for monitoring alarm status. The special designed big open door can close and secure easily without gas leakage. The volume of chamber and size of samples shelves are custom-made. It can hold 100 alarms normally. The controller injects quantitative high concentration gas into chamber and the gas stirred by circulating fan to get homogeneous test gas in certain concentration. That gas will be test gas for response test or threshold setting of gas alarm product. The circulating fan and porous plate are also specially arranged to get uniform test gas and avoid the high concentrating gas getting into alarm directly during gas injection.
On the top of chamber, the inlet and outlet and exhaust fan are controlled by PLC to exchange air in chamber.
Component
1. CH4/CO gas controller
1) Set the gas volume and inject gas with precision control.
2) The gas was injected in to chamber in short time and mix quickly. It is easy to count response time of alarm
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Equipment Functions:
The equipment provides a sealed stainless steel test chamber that can accommodate approximately 200 gas detectors. Through the controller, a high concentration of target gas can be quantitatively injected to form the required test gas concentration inside the chamber. It can be used for batch calibration or testing of carbon monoxide and combustible gas detectors. The chamber is equipped with an air circulation fan, which allows the test gas to diffuse quickly and achieve a uniform and stable test gas concentration, avoiding adverse effects caused by high concentration gases on the detectors. The top of the chamber has gas inlet and outlet ports and an exhaust fan. The inlet and outlet ports are controlled by solenoid valves. After opening the solenoid valve and starting the exhaust fan to remove the test gas from the chamber, the chamber door can be opened to replace gas detectors. A movable sample rack is used to install samples. Aged samples can be directly pushed into the calibration test chamber, saving assembly and disassembly time.
1) Multi-functional integration: can be used for both calibration and testing of various gas detectors;
2) Unique gas injection method, short injection time, fast gas injection;
3) Carefully designed air circulation method, even and stable wind speed, fast diffusion, uniform within 60 seconds;
4) Large volume, suitable for batch production testing, can accommodate about 200 detectors;
5) Good chamber sealing, safe and stable;
6) Double-glass doors for easy observation of detector status;
7) Touchscreen control, convenient operation;
8) Equipped with own gas cylinders, primary pressure reducers, gas cylinder cabinets, gas analyzers, etc.
Equipment Parameters:
1) Model: ZNGAS-700
2) Power supply: 220V AC, Power: 3kW
3) Standards: EN50194-1, EN50291-1
4) Gas type: Parameters for carbon monoxide, methane, and propane can be set individually
5) Cabinet: Stainless steel cabinet, double-sided tempered glass, Dimensions: 1.8m x 1.1m x 1.7m
6) Trolley dimensions: 163 x 66 x 143 cm
7) Cabinet door: Electromagnetic lock for safety, locks before gas injection, unlocks after exhaust
8) Product trolley: One set, 5-layer shelving, 400*300mm stainless steel nameplate (drilled and installed with connectors according to customer drawings)
9) Includes: Circulation fan, exhaust fan, air inlet valve, exhaust valve, adjustable internal airflow
10) Controller: 7 touch screen control, time control mode or calibrated concentration control mode, gas injection control, fan control, exhaust control
11) Product power supply: Three-prong socket inside the cabinet, AC uses 10A socket, DC uses 16A socket, manual switch to toggle 220V/110V voltage
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Device features:The fire sensitivity laboratory is suitable for use in UL 217, UL268 and other standard fire test rooms, testing system room temperature sensor, furnace temperature sensor, data acquisition, computer and testing software.The test software can be connected to collect real-time test data such as optical smoke density meter, ion concentration meter, temperature and humidity sensor, record alarm values, and the software can select various material combustion test curves.
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Parameter:
a) Framework: Aluminum profile test bench,
b) Test station: one station
c) Equipment space: 0.6m long x0.4m wide x1.2m high
d) Lock cylinder mounting base: suitable for European profile cylinder, with loading
e360
f/
gPLC
hHMIWinview
i
EN 1303 5.8
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The equipment meets Standard requirement of ANSI/BHMA A156.3-2020EN1125and EN179 to perform durability, operational and strength test. It is suitable for panic exit device. The operating force (release force) can be monitored during cycle test, and the specific cycle number and the release force limit can be set on the HMI.
The test door can be closed by door closer or pulled to close by actuator. It is applicable for Grade 1 to grade 3 and can be set to different test method as described in standards
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
Compliance with the latest standards: The equipment is designed in strict accordance with the latest standards EN 1154 and ANSI/BHMA A156.4, which can meet the performance test requirements of door closers.Four-station design: The vertical four-station design can test four door closers at the same time to meet the needs of batch testing and improve test efficiency.
PLC control and touch screen operation: Automatic control with PLC (Programmable logic controller), equipped with user-friendly touch screen interface, it is easy to set up test procedures, adjust parameters and monitor the test status in real time.
Pneumatic drive and flexible adjustment: The linear cylinder drives the swing arm, which can flexibly adjust the opening Angle and opening time of the door to meet different test needs.Independent control and non-interference: Each station is controlled separately, non-interference, to ensure the independence and accuracy of the test.Real-time monitoring and automatic shutdown: Equipped with sensors to monitor the test process in real time, when the sample of the door close fails, the equipment will automatically stop and prompt fault information.
Equipment parameters
ModelZNEN1154-N
Frameheavily duty steel tube and baking finish
SizeL 3.5 m * W 1.3 m * H 2.6 m
Operation space3.5m * 3.5m * 2.6m
Test door size 916mmx 2000mm
Door opening angle0905(adjustable)
7
EN 1154ANSI/BHMA A156.4
440kg
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The equipment is designed to test and record opening and closing moment of door closer continuously from 0 degree to 180 degree opening.
1Door closer is installed on the test door;
2The servo motor open the test door from 0 to o the maximum opening angle or 180 under
speed of 1 /s, and record the opening force and opening degree during the process;
3Then, the motor reverses and slowly releases the door leaf, and the doorclose from 180 to 0
under the action of the door closerRecord the closing force and degree of the closing process;
4The opening / closing process come out "force vs angle" curve (as shown in Figure 1);
5Calculate the dataand generate the performance test report of closing force value according to EN
1154:1997+A1:2006, ANSI/BHMA A156.4:2019 (As shown in Figure 1) and test method and report
for QBT2698-2016
Equipment parameters
ModelZNEN1154-S1
Equipment frame: aluminum profile frame and test door.
Frame sizeL 1.2 m * W 1.2 m * H 2.3 m
Test door: 2000 (H) * 1000 (W) * 40 (T), about 30kg (up to 160)
Motor power force: 215Nm
Opening / closing speed: < 1 / s
Installation: standard arm parallel arm surface mounting
Force meter: 500N (50kg), reading accuracy 1.5%
Angle sensor: accuracy 1%, resolution 0.1% 8. Action: in the whole process of opening / closing, it is gentle without obvious shaking (except the sample quality);
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
Hinge test equipment is used for friction torque test and durability test of single axis hinges and concealed hinges. It has been updated to new generation with control and monitoring function. It is pneumatic driving and sliding connection to eliminate additional load apply to testing hinge except the door mass and natural effect of open and close movement. The equipment steel frame and steel door are finely made to ensure strict mounting requirement and easy to change different hinges
The equipment includes frame, four test doors, four sets of mounting base plates, four sets of pneumatic driving devices, and touch screen; It does not include general tools or test instruments (such as force meter, torque meter, scale, stopwatch, caliper, level ruler, angle ruler, and shear device etc.)
1)The equipment was designed according to EN 1935.
2)Load the test door according to hinge grade
3)Measure initial friction torque, vertical and lateral distance.
4)Open and close test door via air cylinder between 0 to 90 +/-5 degrade
5)Measure initial friction torque, vertical and lateral distance again and verify the hinge abrasion.
6)The test door and frame were made of heavy duty steel tube and can support the highest-grade hinge test door with maximum door 480kg.
Equipment parameters
ModelZNEN1935-1
Frameheavy duty steel tube frame with changeable hinge mounting plate
SizeL 1.3 m * W 1.3 m * H 2.6 m
Lab space3.5mx 3.5m
Door opening degree0905 adjustable
Standard: EN1935 ANSI/BHMA A156.1
Test frequency60030 cycles/hours adjustable
HMITouch Screen
Test doorEN Test doors: 4 sets, about 60kg per door (Additional Load not included
CyclesEN 1935: grade 3:10 000 cyclesgrade 4:25 000 cyclesgrade 7:200 000 cycles
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The equipment is designed and manufactured according to ANSI/BHMA A156.1Clause 6.6, which meets the requirements of the standard.
Used to test the durability of the Electrified hinge, connect the rated power supply on the hinge over the line, perform the switch test on the hinge, and check the electrical conductivity during the life test of the hinge switch.
Equipment parameters
ModelZTBHMA-3G
Framestand-alone test stand
SizeL 0.8 m * W 0.6 m * H 1.3 m
Test station: 3 stations
PLC control: Panasonic, test scheme and parameter setting, fault monitoring and shutdown
Touch screen (HMI) : set the number of life times, keep counting display after power failure
Test speed: 10 times/min, adjustable
PLC: Panasonic ; Pneumatic parts: Airtac brand.
Power supply: AC, DC, pulse, configurable
Test standards ANSI/BHMA A156.1Clause 6.6
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
Use for hinge shear strength test according to EN 1935. Manual operated hydraulic cylinder apply the force
Equipment parameters
ModelZNEN1935-1Q
Frame: aluminum profile stand-alone test machine
SizeL 1.0 m * W 0.5 m * H 1.1 m
Mounting plate: one set
Force gauge: 15 kN
Standard: EN1935
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The door handle durability test bench is specially designed for typical European door handle that can be separately sold to user. It is used to one vertical load to simulate the loading of mortice lock and another horizontal load to simulate the loading of pull force when open to the door. It is easy to adjust the xyz position of driving motor to fit with different type of door handle. It is PLC controlled device and can monitor any failure and stop testing on time.
Standards EN 1906 7.3.6 Durability of mechanism
Equipment parameters
ModelZNEN1906-1
BenchStandalone table with casters
SizeL 1 m * W 0.8 m * H 1.4 m
Handle mounting block350mm * 150mm * 40mm
Test stationone or two test stations
Handle angle3060 degree adjustable
Load P60N100N, changeable
Load L60N100N, changeable
Panasonic PLC controlfailure monitoring
Standards EN 1906 7.3.6 Durability of mechanism
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The equipment has been carefully designed, integrated strength cylinder, pre-load cylinder, force display, convenient sample clamping, apply a variety of force values, for testing handle strength, deformation, horizontal direction, vertical direction clearance and other energy tests.
The equipment is designed to perform Strength test of door handle, including torque resistance, pull loading and free play.
Standards EN 1906 Strengthy of mechanism
Equipment parameters
ModelZNEN1906-2
BenchStandalone table with casters
SizeL 1 m * W 0.8 m * H 1.4 m
Maximum load2500N
Force gauge03000N
Dial indicator025mm
Excluded torque meter
Standards EN 1906 Strengthy of mechanism
Test itemsEN 1906 clause 5.2, 5.3, 5.4, 5.5, 5.6, 5.7, 5.9, 5.10, 5.11, 5.12, 5.13, 5.3
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The equipment is designed to test operational and durability performance of mechanical locks according to European harmonized standards. A special loading and action device was equipped on this automatic machine to load the latch bolt during operating the lock follower. This lock handle is operated by servo motor to provide high reliable performance. A step motor was used to operate the key or turn in high repeatability and exact angle control. It is super value added facility to identify classification and quality of lock or find out any product defect.
Equipment parameters
Model ZNEN12209-1P
Frame: Standalone frame constructed by 5050 heavy loading steel tube.
SizeL 1.2 m * W 1.1 m * H 2.35 m
Test doors: one set of test doors with 5050 heavy duty steel tube, it can support heavy test door weight 200kg
Test door mass: about 80kg per door. additional load plate:240kg
Door handle cycle operation: operated by servo motor with controlled operating torque. 10 Nm Maximum driving moment
Door position is monitored by optical sensor
Key cycles operation: step motor driving, precise angle control, 5 Nm maximum driving moment.
Latch loading: special designed adjustable mass load of 0, 10N, 25N, 50N, 120Napplied
Closing force: special designed adjustable mass load of 0 to50N apply to test door to close to door.
Pneumatic parts: Airtac brand
Servo motor: Panasonic servo motor
PLC: Panasonic
Standard: EN 12209: 2016
Touch screen monitor: friendly human interface touch screen to control cycles test, setting and display cycle times. Will not lost record even power off.
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The equipment is designed to test operational and durability performance of mechanical locks according to European harmonized standards. A special loading and action device was equipped on this automatic machine to load the latch bolt during operating the lock follower. This lock handle is operated by air cylinder to provide high reliable performance. An motor was used to operate the key or turn in high repeatability and exact angle control. It is super added value facility to identify classification and quality of lock or find out any product defect.
Equipment parameters
Model ZNEN12209-2
Frame: Steel frame, paint
SizeL 1.4 m * W 1.2 m * H 2.4 m
Test door size: 2100mm * 1100mm
Test doors: Two test doors with steel frame with enough strength to support the door mass
Test door mass: 60kg, User can easy increase to desired test door mass by stack steel plate, for examples 200kg if needed.
Door handles cycle operation: operated by air cylinder. Door position is monitored by optical sensor. 10 Nm Maximum driving moment.
Key cycle operation: motor operation with precise angle control, 5 Nm maximum driving moment
PLC: Panasonic ; Pneumatic parts: Airtac brand.
The equipment meet with standards requirement of EN 12209: 2016
Latch loading: special designed adjustable mass load of 0, 10N, 25N, 50N, 120Napplied latch bolt when operate door handle or key to open the door.
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
The equipment is designed for the life test of mechanical lock body, electronic lock body and emergency escape lock. The equipment has comprehensive test function and covers a wide range of lock body types. The opening and closing load can be set for different levels, and the corresponding test program can be selected, and the equipment can automatically perform the life test of the corresponding product.
The equipment adopts a new optimized design, which is more convenient to use.Test items: 1) Handle operation inclined tongue life test; 2) Key or knob operation dumb tongue and inclined tongue test; 3) Night lock tongue test;4) Emergency escape lock; 5) Electronic lock body test function.
Equipment parameters
Model ZNEN12209-3
Frame: Steel frame, paint
SizeL 1.4 m * W 1.2 m * H 2.4 m
Test door size: 2100mm * 1100mm
Test door weight: 100kg or 200kg, 10kg increment is adjustable
Latch load: 0, 10N, 25N, 50N, 120N, adjustable
Hand operation: servo motor control, up/down, Angle adjustable
Handle torque: less than 10 Nm
Touch screen: set the number of life times, keep counting display after power failure
The equipment meet with standards requirement of EN 12209, EN 14846, EN 179
PLC: Panasonic ; Pneumatic parts: Airtac brand.
Closing force: 7 50N, adjustable
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Test equipment function
This equipment is in strict accordance with the standards EN 12209, EN 14846, GA 374-2019. The test requirements are designed and manufactured, applicable to the laboratory of the certification body, and can also be used for pre-production product design verification in the factory and sampling testing of products in production.
The equipment is specially designed for mechanical lock body, electronic lock body strength test, including lock tongue side pressure test, lock tongue end pressure test, buckle tensile test, torsion test, operating force test.
Equipment parameters
ModelZNEN12209-1T
Frame: aluminum profile stand-alone test machine
SizeL 0.8m * W 0.6 m * H 1.4 m
Test positionone position
Meet the test requirements of EN 12209, EN 14846, GA 374-2019.
Additional Information:
Payment Terms : T/T
Packaging Details : Wrapped in pearl cotton and packed in a wooden crate
Delivery Time : 45
Happy Chen (zomtest)
广州市增城区永宁街蒌元村政岭路1-1号, Guangzhou - 511300, China
Share us via
Write a Review
