Sanghavi Group

Makarba, Ahmedabad, Gujarat

"MY MIX - MCR(Microconcrete)" is cementitious, non -shrink, flowable, high strength micro-concrete for structural repair with high precision concrete. It is recommended thickness is up to 40mm to 100mm. It is suitable for various structural strengthening measures such as encasement buildups, jacketing etc.

• Flowable mortar eliminates honey combination
• High early and final strength
• Compensation for shrinkage and settlement in the plastic state
• Develops high initial and final strength
• Excellent resistance to moisture ingress
• Easy to use

• Ensure leak proof shuttering before starting work
• Add 4 to 4.5 liters of water for 25 kg of MCR. The approx. ratio of 16% to 18% by weiht
• If concrete thickness is more than 100mm, Mix 5 to 10mm prewashed coarse aggregate
• Do not use vibrators, avoid vibration for 23 hours after pouring MCR

• 25 kg bag and Project packing of 40 kg bag is available on demand

• Factory sealed bags are best before 12 months from the date of manufacturing in unopened condition stored in dry area.

"MYMIX - SLU(Self Leveling Cement based Underlayment)" is a blend of specially selected cements, graded aggregates, synthetic polymers and workability aids. It is supplied as a dry powder requiring only, the addition of water to produce a smooth free flowing and self leveling smoothing coat, which can be laid to a feather edge. When thickness greater than 10mm is required, washed concrete sand can be added in equal proportions (if sand is added the product becomes trowellable and is no longer self leveling).

• Easy to use, simply add measured Quantity of water
• Time saving, Self levelling giving quick easy lying
• Excellent Bond, content ensures built in adhesion and a firm bond to substrate
• Rapid Hardening, Enables early fixing of floor covering

• For leveling out uneven RCC floor surfaces prior to covering with floor finishes. e.g. tiles, carpeting, linoleum, rubber and other sheet flooring

• Clean Application Area from dust & grease
• Pour 4.5 to 5.5 litre water in a bucket
• Add 25 kg product in the Bucket
• Mix thoroughly preferably with mechanical stirrer or manually
• Do not mix more material that can be laid in 10 minutes
• Ensure that next mix is ready to pour without any interval
• Prewet application area, avoid direct sunlight
• Pour the prepared mix on to the substrate with trowel
• Do not attempt to float the setting surface
• If mix stiffens before it has been spread it must be discarded
• Wait for 24 hours before use

• 25 kg bag and Project packing of 40 kg bag is available on demand

• Factory sealed bags are best before 12 months from the date of manufacturing in unopened condition stored in dry area.

MYMIX RITESEALTM(Waterproofing System) is powder based single component, high polymer modified, elastomeric, waterproof coating for all kind of cementitious surfaces. It has very high water permeability against hydrostatic pressure with standing capacity. It is to be mixed with water and applied by paintbrush.

• All cementitious RCC plastered surfaces
• Interior and Exterior wet areas

• Two coats 1 sq. mt./ kg.

MYMIX - CWC(Cementitious Crystalline Waterproofing System) is an integral capillary concrete waterproofing compound which waterproofs and protects concrete in depth. It consists of Portland cement, specially treated quartz sand and special chemicals.

• Easy to apply
• Penetrates deeply and seals concrete capillary tracts and shrinkage cracks
• Applicable for either positive or negative side pressure
• Effective under high hydrostatic pressure
• Tear or puncture resistant
• Does not require protection
• Withstands aggressive saline or chemical attack

RITEPOXYTMESG 1200(Epoxy Stain-free Grout) is designed specially for use in filling up joints of ceramic tiles, vitrified tiles and stone joints, where hygiene is of utmost importance such as bathrooms, kitchens, living room, bedroom, hospitals, laboratories, swimming pools and high traffic areas.RITEPOXYTMESG 1200is three component, easy to mix, chemical resistant joint filler and is available in 28 shades.

RITEPOXY GLITTER STARTMGrout is epoxy base tile grout designed specially for floor & wall areas, where aesthetics is of utmost importance such as hotels, restaurants, kitchens, showrooms, living room, swimming pools & Shopping Mails.RITEPOXY GLITTER STARTMis a three component epoxy based grout and easy to mix joint filler available in 24 shades in Gold, Silver and Copper finish.

• For interior and exterior floors and walls
• Colour fast and 100% Stain free
• Available in Gold, Silver and Copper colour finish
• Chemical Resistant with non-toxic properties
• Anti-bacterial and Anti-fungal
• Strong, durable and easy to clean
• Ideal for waterproof grouting

• Clean application area & remove dirt, dust & excess adhesivefrom tile joints.
• Mix Part A & Part B in a bucket thoroughly and slowly add Part C (filler Powder) to make a homogenous mixture.
• Using rubber float fill-up the tile joints.
• Wait for 30-45 mins for joints to harden.
• Begin initial clean-up with water & gently use scrub pad in circular motion to remove excess material from the tile/ stone surface.
• Use plenty of clean water until excess grout is cleared from surface.
• To remove excess material from the tile surface use wet towel at 45 degree to the grout joints.
• Wait for 2-3 hrs before giving smooth finish to grout surface with a sponge & hand-glove finger with mild shampoo water.
• Wait for 24 hrs and finally clean the surface with water to remove the epoxy marks.
• Surface is now ready to use.

• Swimming Pools
• Lounges
• Residential and commercial

• Varies with width and depth of joint.

• Available in 1 kg and 5 kg units

• 24 months from the date of manufacturing.

RITEPOXYTMEIG 2200Industrial Grout is an Epoxy based Grout (100% solid) designed specially for use in application at industrial and commercial areas where high strength, free flow, chemical & temperature resistance is required.RITEPOXYTMEIG 2200is easy to mix joint filler available in four shades (Brilliant white, Terracotta, Natural grey, Jet black).

• High Strength and 100% solid epoxy grout
• High Chemical and temperature resistance
• Abrasion resistance
• Anti-bacterial and Anti-fungal
• Strong, durable and easy to clean
• Acid & Stain resistant

• Clean application area & remove dirt, dust & excess adhesive from tile joints.
• Mix Part A & Part B in a bucket thoroughly and slowly add Part C (filler Powder) to make a homogenous mixture.
• Using rubber float fill-up the tile joints.
• Wait for 30-45 mins for joints to harden.
• Begin initial clean-up with water & gently use scrub pad in circular motion to remove excess material from the tile/ stone surface.
• Use plenty of clean water until excess grout is cleared from surface.
• To remove excess material from the tile surface use wet towel at 45 degree to the grout joints.
• Wait for 2- 3 hrs before giving smooth finish to grout surface with a sponge & hand-glove finger with mild shampoo water.
• Wait for 24 hrs and finally clean the surface with water to remove the epoxy marks
• Surface is now ready to use

• Industrial and Commercial areas
• Hospital OT areas
• Dairies
• Food and Beverage processing units
• Pharmaceuticals
• High traffic areas

• Varies with width and depth of joint.

• 5 kg pouch and 10 kg units

• 24 months from the date of manufacturing.