Our Product / Services
We offer the best product range of Reynolds Apparatus, Bernoulli Theorem Apparatus, ANAESTHESIA APPARATUS MAJOR, Orifice Meter Apparatus and Anaesthesia Apparatus.
Sump Tank: Made of M.S. Powder CoatingM.S. FRP LiningS.S. Unit of suitable size and provided with a small storage tank for supply of colored liquid with tubing and cock. Transparent Glass Tube: A transparent tube of 12mm OD and 8mm ID and 600mm length for flow observation provided with a GM control valve.
Supply Tank: M.S. Powder CoatingM.S.FRP LiningS.S. Unit of suitable size provided with piezo meter for the measurement of total potential head. Variable Cross Section Transparent Duct: A transparent duct made of acrylic and of smooth variable cross section with suitably spaced 0.5m height replaceable high quality graduated glass tubes to measure the pressure head along the duct and a GM flow control valve.
Cat. No. D-AN 1016 INTRODUCTION Anesthesia machines developed by Ramedico are of the highest quality. The technology used in D-AN 1016 is controlled in every way to give a proper dose of the required agent. The anesthesia machine developed by Ramedico has controlled flow of oxygen and nitrous oxide in ranges of 100cc/min and 200cc/min. there are separate gauges to monitor the supply of uoxygen and nitrous oxides. The position of the oxygen unit is located at a convenient position. The ether vaporizer is also of a premium type and of standard quality. The machine comes with a Goldman type halothane vaporizer. The safety measures are of the highest quality in this machine. It has measures to cut off the supply of nitrous oxide if there is an obstruction in the flow of oxygen. It also has a mechanical alarm in case where the oxygen pressure gets reduced. The anesthetic machine developed by Ramedico has provision to fit in with a ventilator. This increases the usage in case of an emergency situation. The machine also has a closed and open system and the changeover can be performed easily. The hardware of the product is also of standard quality along with enhanced Bains circuit.
Piping System: Consisting of Two G.I. Pipe lines, each line fitted with a venture meter and orifice meter of size 25 mm with a gate valve and provided with a set of distribution chamber having isolating cocks to facilitate experiment on individual venture meter or orifice meter.
D-AN 1011 is one of the finest and compact machines developed for anesthetic usage. It comes with the best features in terms of safety to deliver best results in any operation of surgery. The safety of D-AN 1011 has been of the most valuable essence. It comes with a Nitrous Oxide lock and a visual alarm system that controls the flow of the element through the machine. The Rotameter embedded in this machine is designed to control the flow of Nitrous Oxide in a singular way and it allows the flow of Nitrous element only until 1 liter of oxygen has been released. The Rotameter can also be easily removed and cleaned whenever desired. The control knobs have been given specific color for easier identification. They also have a characteristic tactile profile to help the anesthesiologist control the system in a better way. The machine has been designed in a desirable manner and the oxygen knob has been placed before the Nitrous control knob. Also the machine has separate inlet connections to eliminate the chances of interchangeability between the oxygen and nitrous flow. The device comes with an exclusive carrying case. It also has all the required accessories for convenience of carrying around.
We are offering vicat needle apparatus. the apparatus consists of a metallic frame bearing a freely movable and with a cap at top, one vicat mould and glass base plate and one set of needles one each initial needle, final needle and consistency plunger.
We are offering gillmore needle apparatus. a base with a vertical shaft and two horizontal arms. The lower arms is adjustable for height. 1 no. Initial needle 1/12-inch dia ¼ lb. Wt. 1 no. Final needle 1/24 inch dia. ¼ lb. Wt. 1 no. Glass base plate. Complete as above
Simple Demonstrations: Observation of the pressure profile at the various conditions of load and speed. Experimental Investigation: After noting the pressure profile for any chosen conditions the following analysis may be conducted. Plotting the Cartesian and polar pressure curves.
The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800 mm from the centre of the table. There is a projecting lug with a plane face on the upper face of the table beneath which is a stop with a rounded upper surface. The table can be raised and allowed to fall freely on the stop by a cam which is connected to a motor and gearbox through a V-belt an pulleys. The cam rotates at a rate of 60 RevMin. A stroke counter fitted with micro-switch is provided which stops the machine after 60 Jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surmounted by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Suitable for operation on 230 Volts, Single Phase, A.C. Supply. A Digital Preset Counter can be supplied at an extra cost.
The machine facilitates the study of dynamic behavior of cam follower. It consists of a DC Motor coupled to an extension shaft whose and carries a cam. A cam follower, mounted on the end of a vertical bar, is loaded on the cam face by compression spring is retained by a cross bar mounted on two vertical pillars attached to the base plate. Facility is provided to vary the pre compression of spring. The inertia of follower can be altered using weights.
Notch Tank : Notch Tank of suitable size having arrangement to fix replaceable notches with a set of welded mesh baffles for accommodating ¾ "1" crusher stones for steadying the flow of water Notches- (Brass): a. Trapezoidal Notch b. Rectangular Notch-100mm width. Hook Gauge: 30cm range with mounting provision.
This compact and simple apparatus incorporated two features. Firstly, kinematics coupling at the driven and of the shaft to slide freely in longitudinal direction while revolving readily. The directional clamping of this end of the shaft is achieved by and interchangeable chuck without self aligning radial ball bearing. Dia. (MM)
The slump cone in these slump test apparatus is filled with freshly mixed concrete and tamped with a tamping rod in three or four layers. The top of the concrete is leveled off with the top of the slump cone, the cone is lifted vertically up and the slump of the sample is immediately measured. The complete slump test apparatus set comprises of a Steel Octagon Base Plate (8 faces) with carrying handle, Graduated Tamping Rod 16mm dia. x 600mm long with one bullet end, slump cone having base 200mm, height 300mm fitted with handle.
INTRODUCTION The Endometrial Biopsy is the surgical ablation of the inner layer of the uterus or womb, the uterine lining for the microscopic anatomy of the tissues. Surgeons who supervise such operations prefers a Curette more oftenly than other surgical instruments. A curette is a thin metallic tube having an open tip on one side formed in the shape of a small scoop, hook or gouge. A syringe is attached to it and applying suction through the given, tissues is extracted for tissue culture and further progressed by physicians who conclude their diagnosis performing a histologic evaluation on such formed samples. Variously used than cited here, it is for cervical dilation, debriding biological tissue, trimester abortion or removal of jammed ear wax. Endorsed for single use to avoid pestilence, our Ramedico Endometrial Curettes bear unparalleled features and objectives such as:- . Sterile and disposable. . Designed for efficient localized suction . Provides clean and consistent biopsy samples . Shaped with appropriate small diameter. . Designed with a unique combination of rigidity and flexibility. For customer satisfaction, our brand and brand products are assured to be not compromised with any quality conditions. Our product is considered to contain easement and comfort for the medical practitioner as well as the patient. Our Curette Endometrial Biopsy units bear countless unbeatable features, yet, the product is quite competitive in the souk. We understand the cost of life of a human and thus, we have conducted every possible test on the units to supply flawless products to the healthcare centers.
Consists of a torque head adjustable in height by means of a lead screw rotated by a drive wheel to enable the vane to be lowered into the specimen. Rotation of the vane is by means of a hand wheel which operates a worm gear arrangement turning the upper end of a calibration torsion spring, vane dia, rod dia, vane size & vane height are as per IS specifications. The vane shaft is attached through the hollow upper shaft to a resettable pointer, which indicates the angle indicates the angle of torque on a dial graduated in degree the dial reading multiplied by spring factor gives the torque a container for soil sample is also supplied & a sampling tube of 38mm. i.d. & 150mm long can also be used as container . Supplied with set of four springs, one each of approx. 2 kgscm sq., 4kgscm sq., 6 kgscm sq. & 8kgscm sq. complete as above in a wooden carrying case.