Our Products
SAW FRAME : This of regid construction & runs in prismatic guide ensuring a parallel cut. This cut takes place on the draw stroke & the hydraulically liften out of contact with the workpiece on the forward stroke to prevent wear or the blade & can out metals of all kinds & strength. FEED : Two levers are provided at the pot one regulators the rate of feed while the other enabled the bow slide to be raised or forwarded hydraulically bow raised automatically & motor Switched off on completion of the cut. BED : The bed is of large proportion provided with guide ways for the vice for clamping the material vice is of rigid constructional. One jaw remains fixed & the other can be adjusted according the material to be cut. ELECTRICAL EQUIPMENT : A direct on line push bottom starter can be fitted which incorporates & adjustable trip mechanism which stops the machine as soon as the blade is clear from the work non productive time is reduced to minimum. DRIVE : Power is supplied by a suitable electric motor through Vee-Belts which are full adjustable for tension all drive mechanism being totally enclosed. SPEED : The incorporation of two-speed driving mechanism allows for the most suitable speed to selected for material being cut. COOLANT : The Coolant tank is totally enclosed in the machine base & a Speed Pump supplies coolant to the saw blade through a stay put pipe & top.
Standard Accessories : Box Table, Electric Motors AC/400/440 Volts, Panel Board for Centralised electrical Controls and Limit Switches, Machine Lamp, Coolant Pump Complete with fittings, Set of Foundation Bolt, Instruction Manual, Spare part List & Tool Box
MODEL
|
AMI-32 | AMI-40 | AMI-50A | AMI-50B | AMI-50C | AMI-65 | AMI-75 |
DRILL HEAD
|
|||||||
Drilling Capacity (in Steel / Cast Iron) | 32/40 | 40/50 | 50/60 | 50/60 | 50/60 | 65/75 | 75/85
|
Drilling Depth | 140 | 180 | 225 | 225 | 220 | 325 | 355 |
Taper Spindle Nose Socket
|
MT-3 | MT-4 | MT-5 | MT-5
|
MT-5 | MT-5 | MT-6
|
No. of Spindle Speeds & Range (RPM)
|
6(72-1000) | 6(55-665) | 9(45-695) | 9(45-695) | 12(45-1000) | 12(18-810) | 12(18-810) |
No. of Spindle Feeds & Range (mm/rev.) | 2(0.1 & 0.2) | 3(0.1 to 0.2) | 3(0.1 to 0.2) | 3(0.1 to 0.2) | 6(0.125 to 1.25)
|
6(0.125 to 1.25)
|
6(0.125 to 1.25)
|
Drill Power | 1.5 Kw. | 1.5 Kw. | 2.2 Kw. | 2.2 Kw. | 3.7 Kw. | 3.7 Kw. | 5.5 Kw. |
CAPACITY
|
|||||||
Drilling Radius : Maximum (A) | 750 | 1050 | 1100 | 1100 | 1300 | 1700 | 1900 |
Minimum (B) | 350 | 375 | 450 | 450 | 450 | 500 | 600 |
Drilling Head Transverse (C) | 400 | 675 | 650 | 650 | 850 | 1200 | 1200 |
DISTANCE BASE PLATE TO SPINDLE
|
|||||||
Maximum (P) | 835 | 1000 | 1300 | 1300 | 1500 | 1500 | 1750 |
Minimum (M) | 275 | 225 | 225 | 225 | 300 | 300 | 200 |
Diameter of Column Sleeve (D) | 190 | 255 | 310 | 310 | 310 | 355 | 405 |
WORKING SURFACE OF BASE PLATE
|
|||||||
Length x Width | 750 x 650 |
900 x 680 |
920 x 830 |
920 x 830 |
1120 x 830 | 1500 x 1020 | 1625 x 900 |
DIMENSIONS OF BASE PLATE
|
|||||||
Length x Width x Height | 1170 x 670 x 160 |
1480 x 700 x 200 |
1585 x 850 x 200 |
1585 x 850 x 200 |
1800 x 850 x 200 |
2265 x 1040 x 225
|
2650 x 1180 x 225
|
OTHER DETAILS
|
|||||||
Arm Elevating Motor | 0.75 Kw | 0.75 Kw | 1.5 Kw. | 1.5 Kw. | 1.5 Kw. | 2.2 Kw. | 3.7 Kw. |
Standard Box Table (mm) | 400 x 350 x 350 |
400 x 350 x 350 |
550 x 420 x 420
|
550 x 420 x 420 |
550 x 420 x 420 |
600 x 500 x 500 |
600 x 500 x 500 |
Approximate Weight of Machine | 1100 Kgs | 1700 Kgs | 3000 Kgs | 3000 Kgs | 3500 kgs | 4800 Kgs | 6500 Kgs |
Standard Accessories :
Box Table, Electric Motors AC/400/440 Volts, Panel Board forCentralisedelectrical Controls and LimitSwitches, MachineLamp, Coolant Pump Complete with fittings, Set of Foundation Bolt, Instruction Manual, Spare part List & Tool Box
SPECIFICATIONS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
we are leading supplier of this product.
.