Our Product / Services
Our Complete range of products are MM Bench Type Pillar Drill, 38 MM Radial Drill, Hacksaw Machines, 25 MM Radial Drill and All Geared Radial Drill.
| Spindle Travel | 80 | 130 | 130 |
| Spindle Taper | MT-1 | MT-2 | MT-2 |
| No. of Spindle Speeds | 500 - 2825 | 86 - 3360 | 86 - 3320 |
| No. of Feeds | --- | --- | Fine feed /Without |
| WORKING RANGE | |||
| Column Diameter | 46.10 | 73.80 | 87 |
| Max. Dis. Centre to Column | 152 | 200 | 378 |
| Max. Dist. Spindle Nose to Table | 356 | 710 | 585 |
| Max. Dist. Spindle Nose to Base Plate | 510 | 925 | 980 |
| Working Surface of Table | 215 x 222 | 267 x 270 | 395 x 395 |
| Working Surface of Base Plate | 235 x 370 | 495 x 310 | 645 x 375 |
| Electric Motor | 0.5 HP 1440 RPM | 0.75HP 1440 RPM | 1 HP 1440 RPM |
| Overall Dimensions | 725 x 375 x 325 | 1275 x 675 x 425 | 1275 x 725 x 395 |
| Net Weight | 44 Kgs. | 101 Kgs. | 205 Kgs. |
| Wooden Case Dimensions | 775 x 410 x 355 | 1350 x 710 x 465 | 1275 x 725 x 395 |
Standard Accessories Suitable electrical s 3 Phase with Switch and Wiring for AC Supply. Motor Pulley, .V-Belt & square Table Block. Extra Accessories : Coolant Pump, Complete with Assembly, Machine Lamp, Drill Vice, Drill Chuck & Socket.
This cut takes place on the draw stroke & the hydraulically liften out of contact with the workpiece on the forward stroke to prevent wear or the blade & can out metals of all kinds & strength. FEED : Two levers are provided at the pot one regulators the rate of feed while the other enabled the bow slide to be raised or forwarded hydraulically bow raised automatically & motor Switched off on completion of the cut. BED : The bed is of large proportion provided with guide ways for the vice for clamping the material vice is of rigid constructional. One jaw remains fixed & the other can be adjusted according the material to be cut. ELECTRICAL EQUIPMENT : A direct on line push bottom starter can be fitted which incorporates & adjustable trip mechanism which stops the machine as soon as the blade is clear from the work non productive time is reduced to minimum. DRIVE : Power is supplied by a suitable electric motor through Vee-Belts which are full adjustable for tension all drive mechanism being totally enclosed. SPEED : The incorporation of two-speed driving mechanism allows for the most suitable speed to selected for material being cut. COOLANT : The Coolant tank is totally enclosed in the machine base & a Speed Pump supplies coolant to the saw blade through a stay put pipe & top.
| Size | 7" | 8" | 10" | 12" | 14" | 16" | 18" | 20" | 24" |
| Stroke (adjustable) |
5.5" | 5.5" | 5.5" | 5.5" | 5.5" | 5.5" | 5.5" | 5.5" | 5.5" |
| No. of Stroke per min. | 100 to 120 | 100 to 120 | 85 to 100 | 85 to 100 75 to 85 | 75 to 85 | 60 to 85 | 60 to 85 | 60 to 85 | |
| Electric Motor Required | 1 H.P. | 1 H.P. | 1.5 H.P. | 2 H.P. | 2 H.P. | 3 H.P. | 5 H.P. | 7.5 H.P. | 7.5 H.P. |
| R.P.M. | 1440 | 1440 | 1440 | 1440 | 1440 | 1440 | 960 | 960 | 960 |
| Blade Size | 12" to 14" | 14" to 16" | 16" to 18' | 18" to 20" | 20" to 22" | 22" to 24" | 24" to 26" | 28" to30" | 30" to 32" |
| Capacity of Round Bar | 7" | 8" | 10" | 12" | 14" | 16" | 18" | 20" | 24" |
| Capacity of Square Bar | 5" | 51/2" | 8" | 10" | 11" | 13" | 14" | 15" | 18" |
Standard Accessories Box Table, Electric Motors AC/400/440 Volts, Panel Board forCentralised electrical Controls and Limit Switches.
MachineLamp, Coolant Pump Complete with fittings, Set of Foundation Bolt, Instruction Manual, Spare part List & Tool Box Special Accessories : Machine Vice, Boring Attachment, Tapping Attachment, Drill Chuck, Socket & Sleeves & Tilting Table
Rakesh Mittal (Elab Engineering)
F-197/A, ALPHA-2 GREATER NOIDA Gautam Budh Nagar, Uttar Pradesh - 201308, India
Share us via
Write a Review
