Our Product / Services
We are leaders in the market for providing best range of Turbine Trainer, Telephone Trainer, Mobile Phone Trainer, Multi-Process Control Trainer and MIC Trainer
Technical Description Using the pump and turbine unit , an extendable experimental concept for basic experiments in the area of hydraulic fluid-flow machines with PC-Data Acquisition has been realised. Here the forms the basic unit. Equipped with a powerful centrifugal pump and a sealed water circuit with an own supply tank, the module can be used to perform experiments on pumps. Rotational speed, flow rate and back-pressure can be adjusted. The drive power of the pump is determined using the rotational speed and the torque. Modern electronic measuring instruments and digital displays for pressure, flow rate, torque and rotational speed are integrated into the basic unit. The Data Acquisition enables the user to have all measured data on a PC.
The Telephone Trainer presenting by Vinytics is a complete kit to understand the working of telephone instruments with the idea of working of exchange. The trainer has DIP switches to create the faults in the instruments and test points to give the complete idea about the servicing/working of telephone instrument. Based on Basic Telephone Instrument Circuits. 16 Fault creating switches for different sections. Circuit Diagram on board describing different sections in telephone like Line protector, Voltage dropper, Ringer, Dialer, Key matrix, Sound amplifier section etc. Test points to measure the signals in different sections. Can be use as normal telephone instrument. User's manual with fault finding.
Mobile Phone Trainer (GSM) Cellular System : EGSM/GSM 900 Rx Frequency band : EGSM 925.960MHz GSM 900 935 .960MHz Tx Frequency band : EGSM 880 .8790MHz GSM 90 890 915 MHz Output power : +5 +33dBm/3.2 mW .0.2W Channel Spacing : 200KHz Antenna : Loop type, 50W Display : 84x48 pixels On board sections : Antenna, Keypad, SIM, Charging Circuit Clock, User Interface such as Buzzer, Vibrator, LEDs. Features : Screen saver, Ring tones, SMS etc. Accessories included : Battery, Mains cord, Manual, Hands Free Kit CD containing Mobile Phone working. Housed in Attractive cabinet with Protective cover Software : Software CD containing mobile phone working, internal block wise description call route during outgoing & incoming calls.
Multi-Process Control Trainer Technical Description This control trainer is a comprehensive unit featuring only industrial components. It contains a transparent tank for liquid-level and pressure control, a corresponding pipe for flow control, and a two-circuit system with a plate heat exchanger for temperature control. Alternatively, a pneumatically operated control valve or a speed-controlled pump are used as actuator. The parameters of the digital controller can be adjusted over wide ranges so that a large number of different process conditions can be investigated. Electronic sensors measure the individual process values. A three-channel recorder with current inputs is included for recording the control behavior over time. Software for the process visualization and Profibus card are available as an accessory.
We have in store for our clients a quality range of MIC trainer that is available .Our microwave integrated circuit trainer comprises different components and accessories to study the characteristics of various equipment.
Gunn Oscillator Gunn oscillators are used to generate the microwave signal and its micrometer is used to tune the output frequency of gunn oscillator. We are manufacturing gunn oscillator from 4ghz to 110ghz.
Determination of unknown resistances. Determination of the total resistance
of resistors in series,
of resistors in parallel.
Determination of the resistance of a wire as a function of its cross-section.
What you can learn about
Wheatstone Bridge - The Wheatstone bridge circuit is used to determine unknown resistances. The total resistance of resistors connected in parallel and in series is measured.
Add To Cart
Add To Cart
Pump and Turbine Trainer Technical Description Using the Basic Unit, Pump and Turbine Trainer, an extendable experimental concept for basic experiments in the area of hydraulic fluid-flow machines has been realised. Here the forms the basic unit. Equipped with a powerful centrifugal pump and a sealed water circuit with an own supply tank, the module can be used to perform experiments on pumps. Rotational speed, flow rate and back-pressure can be adjusted. The drive power of the pump is determined using the rotational speed and the torque. Modern electronic measuring instruments and digital displays for pressure, flow rate, torque and rotational speed are integrated into the basic unit. Easy to interchange sets with various types of water turbines enable the range of experiments to be expanded to include experiments on turbines.
Rakesh Mittal (Elab Engineering)
F-197/A, ALPHA-2 GREATER NOIDA Gautam Budh Nagar, Uttar Pradesh - 201308, India
Share us via
Write a Review
